燒成制度 的英文怎麼說

中文拼音 [shāochéngzhìdù]
燒成制度 英文
burning schedule
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 燒成 : baking
  1. ( 2 ) the properties of the material with finer andalusite particle size are superior to those of coarse particle size at lower temperature, but properties of material of fine and coarse particle size have little difference at higher temperature. this illustrates that the andalusite particle size can lower the sintering temperature and that it brings forth not remarkable influence on the property of the material when the material is sintered completely

    （ 2 ）對于不同粒度的原料，在燒成溫度較低的情況下，粒度小的材料性能明顯高於粒度大的材料，但在燒成溫度較高的情況下，兩者差別不大，說明原料粒度減小能降低製品的燒結溫度，但在制品均完全燒結的情況下對材料性能影響不大。
  2. For the ceramic materials, the effects of additives such as pbo, b2o3, co2o3, mno2, cr2o3, sb2o3 on the electrical properties of bismuth - free zno - glass varistor were studied. the glass phase formed mainly by pbo and b2o3 during sintering process could decrease the sintering temperature, improve grain uniform growth and inhibit grain second growth. nonlinear property could be improved by properly adding co2o3, mno2, and cr2o3

    對瓷料而言，系統研究了非bi系zno -玻璃料配方體系中pbo 、 b2o3 、 co2o3 、 mno2 、 cr2o3 、 sb2o3等添加劑對壓敏電阻電性能的影響規律，其中， pbo 、 b2o3在燒結過程中形成的玻璃相，可降低燒結溫度，促進晶粒均勻生長，抑制晶粒二次長大， co2o3 、 mno2 、 cr2o3做為非線性添加劑，適量添加可提高樣品的非線性， sb2o3做為改性添加劑，在燒結過程形成的尖晶石相可細化晶粒，抑制晶粒二次生長，改善樣品的綜合電性能。
  3. The influence of burning system on the properties and structure of the ceramic capacitors has been studied under the certain temperature system, the optimum sintering temperature of the ceramics was primarily decided by the content of bi2o3 ? 3tio2. the sintering temperature dropped with the adding of bi2o3 ? 3tio2. at the range of suitable sintering temperature, slow heating and low temperature sintering can obtain fine grain and dense structure. it results in the improving of the breakdown voltage for the middle - high voltage ceramic capacitors

    研究了燒成工藝制度對電容器陶瓷性能和結構的影響，結果表明：在一定的升溫保溫時間下，瓷料的最佳燒結溫度主要取決于組成中bi _ 2o _ 3 ? 3tio _ 2的含量， bi _ 2o _ 3 ? 3tio _ 2含量的增加將降低燒結溫度；在合理的燒結溫度范圍內，慢速升溫和低溫燒結將有利於得到細晶緻密結構，從而改善中高壓陶瓷電容器的耐壓強度。
  4. The raw materials, the composition, the time of milling, the calcining temperature, the different additives, the sintering temperature and the sintering parameters were investigated. the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties, we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature. the lower calcining temperature made the permeability higher, and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite, it is necessary to add effective additives. in this dissertation, the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature, the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites

    研究結果表明:採用高純度的fe2o3有利於獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體，需要嚴格控制配方中各種原材料的含量，優化配方;由於粉體活性受預燒條件的影響，所以對不同要求的鐵氧體選擇的預燒條件就不一樣，適當降低預燒溫度有利於獲得較高的起始磁導率，而為了獲得良好的頻率特性可以適當地提高預燒溫度;根據對粉體顆粒粒徑的不同需求，可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件，本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝，適宜的燒結工藝可以獲得理想微結構和組成，從而得到高性能的鐵氧體材料;而從材料的微結構上來看，要提高材料的截止頻率，就要適當地細化晶粒、增加晶粒內部的氣孔。
  5. The results show that it is an effective method for acquiring better electrical properties that the pressed bodies were sintered at 1150 in furnace with the temperature raised dilatorily, heat preserved for 2. 5 hours and furnace cooled to room temperature

    研究結果表明，氧化鋅壓敏閥片的最佳燒成制度為：隨爐連續緩慢升溫至1150進行燒結，保溫2 . 5小時后，隨爐緩慢冷卻。
  6. Begin with the comparation of two widely used methods producing the strontium titanate, the oxalate decomposition method shows its advantage hi the microstructure and future performance. the effect of caco3 is studied, and so is the effect of the donor dopant, such as nb2o5, y2o3 and la2o3. the dopant of tio2 is also considered, which involve ti / sr ratio, sintering temperature, oxygen partial pressure, donor dopant, grain growth and future electric performance

    從對比草酸鹽分解法和固相合成法這兩種制備srtio _ 3主晶相的方法開始，在予合成料的制備過程中分析了施主nb _ 2o _ 5 、 y _ 2o _ 3 、 la _ 2o _ 3以及caco _ 3所產生的影響；在tio _ 2摻雜的問題上，綜合考慮了ti / sr比、燒結溫度、氧分壓、施主摻雜、晶粒的微觀生長與成瓷后的元件宏觀電性能等之間的相互關系。
  7. The experimental data has been used to validate pdm and low temperature sintering mechanics. the advantage and disadvantage of pdm have been discussed also. for the first time, the pdm is used to study the low temperature sintering mechanics of uo _ 2, and the research results indicate : 1

    3 、基於燒結頸長大速率與緻密化動力學方程得出，影響二氧化鈾低溫燒結的因素有原始粉末粒徑、粉末堆積方式、坯塊原始密度、燒結溫度、燒結時間、燒結氣氛等;粉末壓坯一定時，燒結溫度、燒結時間和燒結氣氛就成為控制低溫燒結的關鍵因素。
  8. The preparation of metal - supported mullite and zro2 / batio3 ceramic membranes was studied. the influences of ceramic composition, sintering temperature and carbon content on the properties of ceramic materials ( porosity, pore diameter and strength, etc. ) were investigated. alkali corrosion resistance and electrolytic experiment results of these ceramic membranes were compared to those of asbestos and al2o3 porous ceramic membranes

    研究金屬支撐平板陶瓷膜的制備工藝技術，陶瓷膜的組成、燒成溫度、碳含量對材料性能（孔隙率、孔徑、強度等）的影響，比較幾種材料的陶瓷隔膜堿蝕量與電解實驗結果。
  9. One - step synthesization made the electrical properties more stable, controling the reducing sintering temperature and retention time can adjust the electrical properties in a certain scope, changing the oxidation temperature made the varistor ’ s voltage v10ma changed, using the special double - layer silver plasm can eliminate the voltage - direction problem

    一次配料得到的樣品電性能一致性更好;控制還原氣氛燒結溫度和保溫時間，可以在一定范圍內調節鈦酸鍶壓敏電阻器的電性能，改變氧化溫度可以獲得不同的壓敏電壓，從而得到系列化產品;採用雙層銀漿工藝成功消除了壓敏電壓的方向性問題。
  10. Samples with various compositions were prepared through different calcined temperature, sinter temperature and different maintained time at sinter temperature. the structure, density, shrinkage, and piezoelectric properties were investigated

    選取部分組成點，採用不同的預合成溫度、燒結溫度和保溫時間制各樣品，測試各樣品的晶體結構、體積密度、線收縮率和壓電性能。
  11. One is about of temperature - dependence of luminescence of eu3 + and tb3 + doped in oxide glass and nanocrystalline y2o3 ; the other is about of light - induced luminescent and structural change in nanocrystalline y2o3 : tb. the creative works are as follows : ( 1 ) euand tb doped nanocrystalline y2o3 with different sizes were prepared by combustion synthesis. dependences of particle size, crystallinity and fluorescence characteristic on ratio of gly / y ( no3 ) 3 and annealing temperature were studied

    本文以變溫與光輻照為實驗方法研究了eu與tb摻雜y _ 2o _ 3納米晶及氧化物玻璃中發光性質隨溫度的變化關系和光誘導y _ 2o _ 3 ： tb納米晶發光性質及結構的改變過程，得到如下創新性研究成果： （ 1 ）用燃燒法制備了稀土摻雜y _ 2o _ 3納米晶，研究了甘氨酸與硝酸釔的反應比例（ g n ） 、退火條件對稀土摻雜y _ 2o _ 3納米晶顆粒尺寸、結晶狀況及發光特性的影響。
  12. The parameters of impregnation are as follows : ph is about 3, the range of temperature is from 20 to 45, and the time is about 2 to 6 hours. after the necessary treatments, zirconia cloths had the optimal strength when the diameters of zirconia fibers were controlled in 4um to 7um, and the sizes of zirconia grains were in 50nm to 100nm. the affec - ting factors were discussed and the liner regression analysis of the cloths was made, from w hich they show that the diameters and grain sizes have the significant influences on zirconia cloths. the obtained zirconia cloths have been accepted for use in nickel - hydrogen batteries by practical use

    研究結果表明：粘膠類纖維布最適合制備氧化鋯纖維布的前軀體；鋯液濃度以飽和溶液為宜；浸漬工藝參數為ph值3左右，溫度20 45 ，時間2 6小時；多餘鋯鹽的去除、浸鋯液后纖維布的整平處理及平燒施應力燒成有利於氧化鋯纖維布的柔軟及平整; 200 600燒成溫度段應緩慢燒成，控制氧化鋯纖維直徑在4 7 m ，氧化鋯晶粒尺寸50 100nm時氧化鋯纖維布的強度最好。
  13. According to the structural characteristics and process requirement of ceramic kiln, we design the control system based on personal computer and single micro controller, realizing the control system and control over temperature and pressure and medium

    根據陶瓷窯爐的結構特點和生產工藝要求，本文採用上下位機相結合，設計了陶瓷窯燒成過程式控制制系統，實現溫度、壓力和氣氛的在線測量和監控。
  14. The thesis emphasis the way and arithmetic of the key equipment of walking reheating furnace : loader machine, unloader machine, walking system, series transfer roll, control system of burning and tracking of steel billet, . make use of the system, we can carry out the function of transferring measuring and weighting, detecting, loading and unloading tracking the steel billet, we can control process of burning and exchange data each other to track the steel billet and manage the process over all of product line. goals of reheating furnace ' s producing process such as high yield, low consuming and pollution, automatic operating mode are achieved

    本文著重研究了步進式加熱爐關鍵設備如：裝鋼機、出鋼機、步進梁、爐前爐后輥道、燃燒控制、板坯物流跟蹤等控制對象的具體控制軟體流程、速度控制曲線、行程計算等具體控制策略和演算法，完成了攀鋼1450熱軋加熱爐基礎自動化系統（ l1 ）和熱工儀表的一級控制，實現板坯輸送、測量、裝出料、物流跟蹤、加熱爐燃燒控制以及板坯庫的數據信息交換，通過plc和二級計算機系統進行順序、定時、聯鎖與邏輯控制，實現了操作自動化與物料系統的全線跟蹤管理。
  15. The influences of the burning system on the microstructure and denseness of the dielectric ceramics have been studied with sem. different burning systems lead to different microstructure and denseness, so the dielectric properties is different

    用掃描電鏡分析技術研究了燒成制度對瓷介材料結構、緻密情況的影響，發現不同燒結制度對瓷介材料的結構、緻密情況不一樣，因而介電性能也就不同。
  16. During preparation added mgo etc as mineralization were added to decreases sintering temperature of al2o3, control the mineral composion and microstructure, optimize the performance of heat and mechanics, etc, resulting in its use in regenerative combustion field

    在制備過程中，引入mgo等礦化劑來降低氧化鋁的燒結溫度，促進氧化鋁陶瓷的燒結，調整材料的礦物組成，控制材料的顯微結構，優化材料的熱學性能和力學性能等，使其能夠應用於高溫蓄熱燃燒領域。
  17. In the section of non - pressing sintered, the influence of different raw material system and sintered temperature on the phase composition of the material were studied. and two conclusions were achieved. the one is that it is good for phase composition design and control because the final phase composition of the material fabricated by ti, sic and c raw material system is comparatively stable

    在無壓燒結階段，研究了原料體系與工藝制度對材料物相組成的影響，結果表明使用ti 、 sic 、 c的原料體系得到的材料最終物相組成比較穩定，有利於進行材料組成設計與控制； 1500得到的材料中的雜質相含量較少，是比較合適的反應溫度。
  18. The thesis mainly investigated the bati _ 4o _ 9 ( bt _ 4 ), which has the lowest dielectric loss in ba - ti system, and ( ba, sr ) tio _ 3, the a position substitute compound of batio _ 3. the dielectric properties of bt _ 4 / bst with different preparation way and different elements doping were investigated. a archimedes method, xrd, sem, impedance analyzer, network analyzer and hakki - coleman method were used to investigate the density, phase formation, microstructure, dielectric properties and doping mechanisms

    本論文以在ba - ti系中具有最低介電損耗的bati _ 4o _ 9 （ bt _ 4 ）高頻介質陶瓷和batio _ 3a位sr取代而得的（ ba ， sr ） tio _ 3 （ bst ）高頻介質陶瓷作為研究對象，對不同粉體制備方法制備的bt _ 4 / bst高頻電介質材料進行不同元素的摻雜，運用阿基米德方法， x射線衍射分析儀，掃描電子顯微鏡和阻抗分析儀，網路分析儀， hakki - coleman法等方法手段和測試儀器測試燒成樣品的密度，相組成情況，微觀結構和介電性能，探討造成介電性能起伏的形成機理。
  19. It was found that there was a close relationship between the adhesion strength of the bg coating and the surface roughness of the titanium alloy and the firing temperature. the chemical state of the elements ti and si at the coating interface varied. the chemical bond and the mechanical occluding make the bg coating form a strong adhesion with the titanium alloy

    通過研究發現， bg塗層與基體的結合強度與基體表面的粗糙度以及燒成溫度密切相關，塗層界面處ti元素和si元素的化學狀態發生了變化， bg與基體強結合的機制為化學鍵和機械嵌合兩種力共同作用。
  20. In the process of making 95 alumina ceramics, selected five kinds of alumina powder and studied the influence of different alumina powder on the sintering properties and mechanic properties of 95 alumina ceramics, moreover, selected the most agreeable alumina powder according to the apparatus for granularity analysis and scanning electron microscope ( sem ). the influence of different sintering temperature on the sintering mechanic properties, the microstructure of 95 alumina ceramics were investigated by adding y2o3 and la2o3 as two kinds of rare earth additives in alumina ceramics. the results indicated that the additive of la2o3 could improve the properties of 95 alumina ceramics more effectively and could get fine grain and tabular alumina that can enhance the strength of the material

    選用了五種al2o3粉料，研究了其對95al2o3瓷燒結性能和力學性能的影響，並結合粒度分析儀sem對al2o3粉料進行優選；通過添加y2o3 、 la2o3兩種稀土添加劑，研究了不同燒成溫度對95al2o3瓷的燒結性能、力學性能及顯微結構等的影響，結果表明：添加la2o3可以有效提高95氧化鋁瓷燒結性能和力學性能，形成細晶和板狀氧化鋁瓷的顯微結構；通過對比不同氧化鋁粉料制備氧化鋁瓷燒成溫度曲線與燒結性能的關系，確定最佳的燒成溫度范圍為1570 ~ 1600 。
分享友人
分享到 Line

分享到臉書