燒燒 的英文怎麼說

中文拼音 [shāoshāo]
燒燒 英文
incineration
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  1. " for it would be fire that consumes to abaddon, and would uproot all my increase

    伯31 : 12這本是火焚燒、直到毀滅、必拔除我所有的家產。
  2. Fried superior shark s fin w abalone sauce ( 2. 5 teals )

    鮑汁干燒大排翅（二兩半）
  3. Spectro - analysis of gas breakdown in laser - induced plasma during laser ablating metal

    激光燒蝕金屬靶時氣體電離分析
  4. Ablating heat shield

    燒蝕熱防護
  5. Laser marking is a kind of technique using heat effect of laser to ablate meterials on object surface so as to leave over permanent press

    激光打標是利用激光的熱效應燒蝕掉物體表面材料從而留下永久標記的技術。
  6. Super - hard amorphous carbon films were deposited on such substrates as single - crystalline silicon and k9 glass by pulse laser ablating graphite target

    本文研究用脈沖激光燒蝕石墨靶方法在單晶硅、 k9玻璃等襯底上生長超硬非晶碳膜。
  7. The charter i introduced the schematics of the experimental setup, the model of pulsed laser ablating solid target ( s - n model ) and the subplantation model for film growing proposed by y. lifshitz

    第一章簡要介紹了實驗裝置、激光燒蝕固體靶的s - n模型和y . lifshitz提出的次表面生長模式。
  8. Study on numerical simulation of laser ablation

    連續激光燒蝕效應數值模擬方法研究
  9. Ablation performance of c c composites with different preforms

    炭復合材料燒蝕性能
  10. Ablation performance and mechanism of 3d c c composites

    復合材料的電弧駐點燒蝕及機理分析
  11. Improvement on ablation and erode of mechanized gun evacuator

    自行火炮抽氣裝置防燒蝕腐蝕的改進試驗
  12. Ablative thickness transducer sensor

    燒蝕厚度傳感器
  13. Abstract : in this paper, two tests are described on air leakage of sinter machine in 2 sintering plant of xiangtan iron and steel co. according to the test results, on the base of analysis and discussion, a series of measures on decreasing air leakage of sinter machine are putted forwored from sealed devices, lubricating oil system, maintenance and management etc. an effective and feasible way is supplied for energy saving and increasing production, decreasding production cost, increasing economy benefit of sintering process

    文摘:通過對湘鋼二燒燒結機漏風率的兩次測試和結果分析，從密封裝置、潤滑系統、附件結構的改進等方面提出了一系列降低漏風率的對策，為燒結工序的增產節能，降低生產成本，提高經濟效益提供了一條行之有效的途徑。
  14. I don't have to do anything except cooking a little and earn my goddam living.

    我呀，燒燒飯，掙口飯吃，沒別的更多的想頭了。
  15. This paper probed into the composition of sanitary ware refire glazes and the repairing process of the flaw on the surface of sanitary ware glaze. investigated the effect of sanitary ware refiring process to the quantity of product and proposed the firing curves of sanitary ware refiring based on it

    探討了衛生陶瓷重燒釉的組成，衛生陶瓷釉面缺陷的修補工藝，研究了衛生陶瓷重燒燒成工藝對產品質量的影響，在此基礎上提出了衛生陶瓷重燒的燒成曲線。
  16. I have pair of little hands, one on left, one on right. . little hands. little hands, with ten fingers on two hands

    原來游游唱的是：我有一雙小小手，一隻左呀，一隻右. . .被老師洋腔洋調的教成：烏央一沙燒燒熟. . . .了。
  17. Left you this way still you pray, you never stray never taste of the fruit

    但是你的心燒燒冷冷哦情哦我看是真難收成
  18. " let the irons be heated, " said the doctor ; " but really it is a useless precaution.

    「那麼，去把烙鐵燒燒拿來， 」醫生說道， 「不過這樣做實在沒有必要。 」
  19. Portable fan - assisted air heaters ; lpg - fired air heaters with heat - exchanger ; safety requirements, testing marking

    便攜式風扇輔助空氣加熱器.帶熱交換器的燒燒液化石油
  20. The optimized preparation conditions were pre - sintering temperature of 910, sintering temperature of 1100 and keeping temperature duration for 6 hours. for sno _ 2 ceramic target, the optimized preparation conditions were pre - sintering at 1100, sintering at 1500 and keeping temperature duration for 6 hours

    其最佳工藝條件為: 910預燒， 1100燒結並保溫6小時;而制備透明導電薄膜sno _ 2陶瓷靶材的最佳工藝條件為:預燒、燒結溫度分別為1100和1500同時保溫6小時。
分享友人
分享到 Line

分享到臉書