燒結材料 的英文怎麼說

中文拼音 [shāojiēcáiliào]
燒結材料 英文
char forming material
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 材 : 名詞1 （木料） timber 2 （泛指可以直接製成成品的東西; 材料） material 3 （供寫作或參考的資料） ma...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 材料 : 1. （原料） material 2. （資料） data; material 3. （適于做某種事的人才） makings; stuff
  1. Taking the andalusite from south africa and alumina fiber as raw materials, adding aluminum sulphate as binder, fabrication and properties of alumina fiber reinforced andalusite composite was studied through wet dispersion, mould pressing and sintering processes

    以紅柱石和氧化鋁纖維為原料，用硫酸鋁作為結合劑，經過分散、混合、半干法成型、高溫燒成工藝，對氧化鋁纖維增強紅柱石基復合材料的制備及性能進行了研究。
  2. Results show that : ( 1 ) for each particle size of andalusite, variation tendency of the properties of the material is generally the same : the maximum of bulk density, compressive strength and rupture strength appears in the range of 5 % - 10 % content of fiber, these properties of the material remarkably decrease as the fiber content exceed 10 % ; while at the same fiber content, the properties of the material increase with the increase of firing temperature

    結果表明： （ 1 ）對于不同粒度的原料，性能變化規律大致相同：在同一燒成溫度下，體積密度、常溫耐壓強度、常溫抗折強度在5 10之間出現峰值，加入量超過10之後材料的性能明顯下降；在相同的纖維含量下，隨著燒成溫度的提高，試樣的各項性能均有所上升。
  3. ( 2 ) the properties of the material with finer andalusite particle size are superior to those of coarse particle size at lower temperature, but properties of material of fine and coarse particle size have little difference at higher temperature. this illustrates that the andalusite particle size can lower the sintering temperature and that it brings forth not remarkable influence on the property of the material when the material is sintered completely

    （ 2 ）對于不同粒度的原料，在燒成溫度較低的情況下，粒度小的材料性能明顯高於粒度大的材料，但在燒成溫度較高的情況下，兩者差別不大，說明原料粒度減小能降低製品的燒結溫度，但在制品均完全燒結的情況下對材料性能影響不大。
  4. We also attainted mosi2 / sic composite by using melting mosi2 infiltrated sic body which shaped by sic powder. the result show that the diameters of sic particle and shaping methods have effect on the composite ' s microstructure and properties

    另外，嘗試了用mosi _ 2在2050下浸滲直接由sic粉體成型的坯體制備mosi _ 2 / sic復合材料。採用sic顆粒的級配有利於提高坯體密度，但是降低燒結體的緻密度。
  5. Sintered bimetal material - determination of shear strength

    燒結雙金屬材料剪切強度的測定方法
  6. The material was sintered at 1050 for three hours to get the porous artificial bone, that its apparent porosity was54 %, its volume density was 1. 28 g / cm3, and its bending strength was 13. 25mpa. the results showed that the sintering temperature was reduced by adding bioglass

    本研究採用含生物玻璃前驅體粉末原料，添加檸檬酸造孔劑，模壓成型，在1050燒結保溫3小時，獲得了顯氣孔率為54 、體積密度為1 . 28s cm ~ 3 、抗彎強度為13 . 25mpa的多孔hap人工骨材料。
  7. The modification effects of wollastonite on the properties of the sls part were investigated

    研究了硅灰石對尼龍12燒結材料的填充改性作用。
  8. It is investigated in the paper the correlation between the microstructure and the mechanical properties, that is, the effect of the content of free carbon, free silicon, pore and granule size on the bending strength of the material. under 1800, we obtain material with a density of 3. 12 g / cm3, bending strength of 522mpa. it is considered that the increase of the bending strength of the material obtained upon the traditional rbsc material by 50 % is mainly owing to a higher density and a lower porosity than the rbsc material

    研究了高溫燒結材料中游離si含量，晶粒尺寸以及游離c和氣孔對材料強度的影響，對比了所得材料與傳統rbsc材料的顯微結構和力學性能的差別，在高溫燒結下制備了密度為3 . 12g / cm ~ 3 ，強度為525mpa的材料，比傳統rbsc材料提高了50 ，材料中更低的氣孔率和更高的密度是強度提高的主要原因。
  9. Case and the shift fork all adopt the aluminum alloy, part of components adopt the sinter material, which realize the light

    殼體、換檔撥叉全部採用鋁合金，部分零件採用燒結材料，實現產品輕量化。
  10. Investigation of wear behavior on nitriding sinter metal materials

    氮化處理粉末燒結材料耐磨性研究
  11. Research and progress of yield criterion for sintered powder materials

    粉末燒結材料屈服條件研究和進展
  12. Railway rolling stock. disk brake linings made of sintered materials

    鐵路車輛.金屬粉末燒結材料制盤式制動襯片
  13. Sintered metal materials ; sint - testing procedures ; part 0 : explanatory notes for spn

    燒結金屬材料. wlb燒結材料規范.第0部分: spn的說明
  14. Study of mechanism of black liquor from banknotes making in high volume fly ash sintered materials

    造紙黑液在大摻量粉煤灰燒結材料中的作用機理研究
  15. To have dewaxing and degreasing systems, the bond in sintering materials can be removed efficiently

    配置脫蠟脫脂裝置，可有效去除燒結材料中的粘合劑等成分。
  16. Sintered metal materials ; werkstoff - leistungsbl ? tter sint - material specifications ; part 2 : materials for filters

    燒結金屬材料. wlb燒結材料規范.第2部分:過濾器用材
  17. Sintered metal materials ; werkstoff - leistungsbl ? tter sint - material specifications ; part 1 : explanatory notes for wlb

    燒結金屬材料. wlb燒結材料規范.第1部分: wlb的說明
  18. Sintered metal materials ; werkstoff - leistungsbl ? tter sint - material specifications ; part 6 : hot - forged sintered steels for structural parts

    燒結金屬材料. wlb燒結材料規范.第6部分:異型件用燒
  19. Spark plasma sintering ( sps ) is a kind of new sintering technology for materials synthesis and processing, it has such advantages as high sintering speed, low sintering temperature, it also can retain the origin state of the sintered materials, as such make the sintered materials keep the state of un - equilibrium in this paper, sps was conceived of treating iron covered silicon powder to keeping the origin state of the powder

    放電等離子燒結（ sparkplasmasintering簡稱sps ）是一種材料快速制備新技術，它具有燒結速度快，燒結溫度低，使燒結材料處于遠離平衡狀態，並能保持材料的原有狀態等重要特點。本文設想制各出鐵硅包覆粉末，再利用sps進行遠離平衡狀態的處理，來獲得保持原始粉末自然狀態的合金塊體。
  20. A successive transformation of the sintering material from powder morphology to high - temperature liquid phase and, afterwards, to continuous solids was simulated by using a “ birth and death ” element technique of the ansys software

    利用「生死」單元技術，模擬了燒結材料由粉末態轉變為高溫液態繼而轉變為連續實體的過程。
分享友人
分享到 Line

分享到臉書