燒結質量 的英文怎麼說

中文拼音 [shāojiēzhíliáng]
燒結質量 英文
sintering quality
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 質 : Ⅰ名詞1 （性質; 本質） nature; character; essence 2 （質量） quality 3 （物質） matter; substance;...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 質量 : 1 [物理學] mass 2 （產品或工作的優劣程度） quality 3 economy （離子源的）; 質量標準 quality level...
  1. In recent years at iron - making plant of pangang, the coke ratio of pig iron has reduced evidently by insisting on “ burden preparation ” course, improving quality of sinter, raising wind temperature, increasing rich oxygen quantity and injecting abundant pulverized coal into bf. the solid fuel consumption of sinter has been decreased greatly through insisting on using high - quality calces, practising high feed sintering, actualizing many techniques in solving key problems. at the same time, the energy source base management has been strengthened, and energy - saving work has made great progress, profits generated by energy - saving have exceeded a hundred million yuan

    近年煉鐵廠通過堅持「精料」方針，改善燒結礦質量，提高風溫，增大富氧，實施大噴煤，使入爐焦比有明顯下降；燒結堅持用好生石灰，推行厚料層燒結，實施多項技術攻關，固體燃耗大幅度下降；同時加強能源基礎管理，節能工作取得長足進步，節能創效益1億元以上。
  2. The simulation results suggest that, at the end of the scanning line, the dissymmetric temperature field and the great temperature gradient result in the balling phenomenon and great thermal stress, which could lead to the destruction of the sintering samples in this region. because of the coupling effect between scanning lines, the balling phenomenon is increased as the increase of the scanning lines, thus the over short scanning lines should be avoided in the sintering process. different scanning strategies have significant influence on the sintering

    模擬結果表明，掃描端點溫度場的不對稱及較大的溫度梯度造成了端點球化現象，並在端點處產生較大的熱應力，使燒結成形試樣易在此處破壞;激光掃描線間的耦合作用使端點球化現象隨掃描線的增加而逐漸顯著，燒結時應避免過短的掃描線;不同掃描策略對燒結成形有很大影響，交替掃描會影響燒結試樣的質量，實際製造時應採用單向掃描策略。
  3. Study on the synthesis of corundum - mullite - gahnite multiphase materials by two - step sintering process using kaolinite as raw material showed that impurities introduced by kaolinite mainly increased the liquid amount at high temperature, which can assist sintering of specimen. the experiment results indicated that the samples with lower gahnite content had better sinterability than others. however, if the gahnite content was relative high, the promoting effect on sinterability caused by kaolinite was not significant

    採用天然原料高嶺土二步煅燒合成剛玉?莫來石?鋅鋁尖晶石復相材料研究發現：天然原料中帶入的雜質主要是增加液相量，促進高溫下試樣的燒結；當尖晶石含量較低時，試樣在1300保溫2h時，在1600燒后試樣燒結性能相比之下較好；而當鋅鋁尖晶石含量較高時，天然料對試樣的促燒作用不是非常明顯。
  4. At last, the conclusions of the whole thesis are drawn, and it is put forward that the future research emphases on the infrared radiation absorption ct technology should focus on : instantly get the absorption projections are the crucial factor to utilize the technology industrially ; on the basis of the hypothesis that the gas is ideal gas, species concentration of particular gas medium can be measured at the same time, which must be helpful to comprehend combustion essence ; if laser source to replaces blackbody stove, for irradiant flame, interferometric projection can be attained, and its temperature distribution will known

    最後，對全文進行了總結，並指出今後研究工作重點。指出：瞬時得到各方向的投影是此技術實用化關鍵；在獲得溫度分佈信息基礎上，進行必要的假設和推導，能同時得到火焰中某特定組分濃度的分佈，這必將進一步我們對燃燒本質的理解；利用方向性好，輻射強度高的激光源代替常規的黑體爐，能得到輻射干涉投影圖像，這樣就能測量所介紹系統不能測量的發光火焰溫度分佈。
  5. Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer

    超聲波由於其空化機理及對液體的流變性影響等特性，在燃油霧化燃燒中逐步引起人們的重視，尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性，但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨，將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手，討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響，並通過具體的實驗，根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律，以便找到超聲霧化的一些規律，豐富對超聲霧化機理的研究，對超聲霧化噴嘴的設計具有一定的指導意義。
  6. This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation

    本文針對該鍋爐在實際運行中存在的問題：在額定負荷下，爐膛出口超溫、低溫段過熱器前煙溫高達936 ，遠遠超過815的設計值；噴燃器四周水冷壁結焦嚴重，過熱器管壁溫度超標，無法帶上額定負荷；甚至有時因燃煤質量的變化，必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中，燃燒器的結構、布置，水冷壁的粘污、結垢，過剩空氣系數、一次風溫、煤種及其濃度變化等許多因素都會偏離鍋爐的設計工況，從而影響爐內的傳熱和燃燒，造成爐膛出口超溫、水冷壁結渣等問題。
  7. Meanwhile, based on the magnetic material theory, a complete analysis and summary are carried out on the three crystal structure and technology theory ; especially the ingredient analysis is made on the microscopical morphology and x - ray diffraction and its mixtures existence and relevant metallurgy about the typical second resource such as coldrolling iron and oxide red, steelmaking sludge and feso4 based on the practeal investigation of the pre - burning materials in domestic products plant, especially the analysis on the domestic markets and components, and connecting with reality and material characters in panzhihua iron and steel ( group ) cmpany, we established the product orientation and developing direction in panzhihua iron and steel ( group ) company ; after carrying out the technology reform on the old no. 1 magnetic product plant of enterprise company, making a detailed study on the various conditions for establishing a plant, the feasible research report is formed of 1400 tons ( per year ) feo preburning material and 3000 tons ( per year ) middle and high quality magnetic products ; so a necessary and reliable supports are provided both theoretically and practically for the development of the magnetic industry in panzhihua iron and s teel ( group ) cmpany

    同時，對磁性材料的理論基礎，尖晶石、磁鉛石、石榴石三大晶系結構以及其工工藝理論進行了較為全面的歸納、分析和總結；尤其針對攀鋼產生的二次資源如冷軋鐵紅、煉鋼污泥、硫酸亞鐵等三種典型原料分別作了成分分析、微觀物理形態以及x光衍射分析、其夾雜物的存在形式及相應的金相分析。對國內鐵氧體磁性材料的預燒料及磁件生產廠家的工藝、設備、技術、成本、質量狀況進行了實地的調研，特別是對國內磁性材料的市場及競爭對手進行了詳盡的分析，在此基礎上，結合攀鋼實際及原料特點確立了攀鋼發展磁材產業的產品定位及發展方向；對企業公司原有磁件一廠進行了技術工藝改造，對建廠各項條件進行了詳細的分析，形成了了年產14000噸年鐵氧體預燒料以及3000噸年中高檔磁件產品的可行性研究報告，從理論上和實踐上為攀鋼磁性產業的發展提供了必要的可靠的依據。
  8. And the impact of processing conditions on the electrochemical performance of the porous sn - cu alloys was investigated. results showed that it was good to add more verdigris and to make the annealing time longer for improving the performance. however, the problem of capacity fading can not be solved completely by this method

    並對制備合金材料過程中所添加物質的種類和比例、燒結時間等工藝參數對合金的性能的影響進行了分析，發現添加堿式碳酸銅，並且增大添加比例以及延長燒結時間對電極材料的循環壽命有利，但是不能根本解決容量衰減的問題。
  9. Based on the analysis of the characteristics of the raw mix slurry preparing process in alumina sintering production process, firstly, a mechanism model based on material balance principle was established as the master - rule model for the quality prediction ; secondly, considering the problem that the alkali liquor composition was unstable and its real - time measurement was difficult, a nn ( neural networks ) prediction model for the prediction of the alkali liquor composition was set up and nesting - integrated with the mechanism model ; finally, using the gray theory for the information mining from the errors of the mechanism model, a gm ( 1, 1 ) compensation model was put forward and parallel - connection - integrated with the mechanism model, achieving a raw mix slurry quality prediction model

    摘要針對燒結法氧化鋁生產過程中生料漿配料工藝的特點，根據物料平衡的原理建立機理模型，作為生料漿質量預測的主規律模型；針對堿液成分波動大且難以實時檢測的問題，對堿液成分含量建立了神經網路預測模型，並和機理模型進行嵌套集成；利用灰色理論對機理模型的偏差數據進行信息挖掘，建立了gm （ 1 ， 1 ）補償模型，並與機理模型進行並聯集成，獲得生料漿質量預測模型。
  10. The experiments showed that wc and vc can dissolve mutually in the carbonizing reaction. when wc ' s content exceeds vc ' s, vc will dissolve into wc and make wc ' s crystal lattice bring aberrance and become wc1 - x, contrarily when vc ' s content exceeds wc ' s, wc will dissolve into vc and also make vc ' s crystal lattice bring aberrance. the surface cermet composite has high rigidity and well wear - resistance

    （ 7 ）採用鑄造燒結技術，通過加入毗顆粒和v班一vc的原位放熱反應成功制取了碳化物陶瓷質量百分數超過60 %的表面金屬陶瓷材料，實驗證實wc與高溫碳化反應生成的vc相互可以很好的固溶，當wc的含量超過vc時， vc可以固溶到wc中，使wc的晶格發生畸變，成為昵卜: ，反之當vc的含量超過wc的含量時， wc可以固溶到vc中，也會造成vc的晶格畸變。
  11. The company possesses advanced machinery and equipment as well as testing instrument, for example, hip sintering furnace, 1000 tons press, high precision grinding machine for roll ring, ultrasonic no damage detector and so on

    公司擁有國際先進的熱等靜壓燒結爐1000噸壓機高精度輥環磨床無損探傷儀等專業化生產設備和檢驗儀器，保證產品質量。
  12. Abstract : in order to optimize sintering operation, pneumatics, mass and heat transportation in sintering process and the effect on the process will be discussed in this paper

    文摘:通過討論燒結過程中的氣體力學、質量和熱量傳輸問題其及對燒結過程的影響，以對燒結工藝進行優化。
  13. The researching work include three aspects : 1 ) after selecting primary material system, the polymer coating process were optimized. the polymer - coated high - temperature alloy powder has been developed on the basis. 2 ) based on sintering and orthogonal experiments, the influence of the prototyping elements on prototyping properties have been initially studied, and the optimal prototyping parameters of this material has been obtained finally

    本文主要研究內容為： （ 1 ）選擇合適的包覆材料體系，對鉬粉的包覆工藝進行了優化實驗，在此基礎上開發了適合於激光燒結成型用覆膜高溫合金粉末材料； （ 2 ）通過激光燒結成型實驗，運用正交實驗方法，系統地研究了燒結工藝參數對成型質量的影響關系，在此基礎上確定了覆膜高溫合金粉末最佳燒結成型工藝參數； （ 3 ）對激光成型件進行了后處理工藝實驗，得到了優化的后處理工藝規程，並製作了合格的后處理樣件。
  14. In the alumina process with sintering, the slurry comes out from the grind with low quality because of lots of uncertainty factors and the delay of composition analysis, the qualified raw mix slurry is commonly gained through arranging

    摘要由於燒結法氧化鋁配置生料漿過程中不確定性因素多，成分分析滯后，造成生料漿出磨合格率低，一般需經調配使生料漿質量指標符合工藝要求。
  15. Purpose : the equipment is used for mensurating the change of weight of materials at different atmosphere during heating process

    用途：高溫熱重氣氛燒結爐用於測量樣品在不同氣氛環境里被加熱過程中質量的變化。
  16. Using advanced welding technology insure high quality and high intensity, high stability

    利用良好燒結技術確保質量優異和高強度高穩定度。
  17. Abstract : the effects of sodium hydroxide concentration and chlorination temperature on effective chlorine content of calcium hypochlorite were tested. the effects of mesh number of standard sieve on effective chlorine content of calcium hypochlorite were tested. the retrieval technology of effective chlorine in mother liquor of calcium hypochlorite was researched, and the effects of cycle number on effective chlorine content of calcium hypochlorite were tested. the results indicate that when sodium hydroxide concentration is 333. 3 g / l, and chlorination temperature is 20, the effective chlorine content of calcium hypochlorite is highest, that when mesh number of standard sieve is 180 mesh, the effective chlorine content of calcium hypochlorite is higher, but the passing sieve rate is not too low, that the cycle number has no remarkable effect on the effective chlorine content of calcium hypochlorite, and the effective chlorine content of calcium hypochlorite is basically above 80 %

    文摘:測試了燒堿質量分數和氯化溫度對漂粉精有效氯含量的影響，測試了分鹽用標準篩目數對漂粉精有效氯含量和過篩率的影響.研究了漂粉精母液中有效氯的回用工藝流程，並測試了循環次數對漂粉精有效氯含量的影響.結果表明，燒堿質量分數為25 、氯化溫度為20時，漂粉精的有效氯含量最高；標準篩目數為180目時，漂粉精的有效氯含量較高而過篩率不太低；循環次數對漂粉精有效氯含量沒有顯著影響，並且漂粉精有效氯含量基本上可以達到80以上
  18. The effects of sodium hydroxide concentration and chlorination temperature on effective chlorine content of calcium hypochlorite were tested. the effects of mesh number of standard sieve on effective chlorine content of calcium hypochlorite were tested. the retrieval technology of effective chlorine in mother liquor of calcium hypochlorite was researched, and the effects of cycle number on effective chlorine content of calcium hypochlorite were tested. the results indicate that when sodium hydroxide concentration is 333. 3 g / l, and chlorination temperature is 20, the effective chlorine content of calcium hypochlorite is highest, that when mesh number of standard sieve is 180 mesh, the effective chlorine content of calcium hypochlorite is higher, but the passing sieve rate is not too low, that the cycle number has no remarkable effect on the effective chlorine content of calcium hypochlorite, and the effective chlorine content of calcium hypochlorite is basically above 80 %

    測試了燒堿質量分數和氯化溫度對漂粉精有效氯含量的影響，測試了分鹽用標準篩目數對漂粉精有效氯含量和過篩率的影響.研究了漂粉精母液中有效氯的回用工藝流程，並測試了循環次數對漂粉精有效氯含量的影響.結果表明，燒堿質量分數為25 、氯化溫度為20時，漂粉精的有效氯含量最高；標準篩目數為180目時，漂粉精的有效氯含量較高而過篩率不太低；循環次數對漂粉精有效氯含量沒有顯著影響，並且漂粉精有效氯含量基本上可以達到80以上
  19. Abstract : some small blast furnace in tanshan district, which based on the resource predominance, make effort to burden material preperation, increase the qualities of sinters and pellets, optimize the burden structure, so there technico - econonic indeces were improved, and the cost of pig iron decreased to 700yuan / t

    文摘:唐山地區的一些小高爐憑借資源優勢狠抓精料，提高燒結礦和球團礦質量，優化爐料結構，從而改善了小高爐的技術經濟指標，使生鐵成本降到接近700元/ t的水平。
  20. The convective term is solved by ausm + ( a sequel to ausm which means " the advection upstream splitting method " ). the 7 species 8 steps model and 7 species 7 steps model of hydrogen / air is used in the hydrogen reacting flowfield, the 9 species 5 steps model of methane, the 10 species 10 steps model of ethane and the 10 species 13 steps model of kerosene are used in the hydrocarbon reacting flowfield, the results of the distributions of velocity, mach number, pressure, static temperature, total temperature, species mass fraction and the combustion efficiency are gained, and the numerical results of the pressure of hydrogen and methane are compared with those of the experiment

    計算中通量項採用ausm +通量分裂格式，氫反應流場採用氫/空氣的七組元八方程模型和七組元七方程模型，碳氫反應流場採用甲烷的九組元五方程模型、乙烯的十組元十方程模型和煤油的十組元十三方程模型，得出了超燃發動機燃燒室流場的速度、馬赫數、壓力、靜溫、總溫和組元質量分數分佈及燃燒效率等性能參數，其中氫和甲烷的計算壓力分佈與實驗結果進行了比較。
分享友人
分享到 Line

分享到臉書