燒結骨料 的英文怎麼說
中文拼音 [shāojiēgǔliào]
燒結骨料
英文
aggloporite-
The material was sintered at 1050 for three hours to get the porous artificial bone, that its apparent porosity was54 %, its volume density was 1. 28 g / cm3, and its bending strength was 13. 25mpa. the results showed that the sintering temperature was reduced by adding bioglass
本研究採用含生物玻璃前驅體粉末原料，添加檸檬酸造孔劑，模壓成型，在1050燒結保溫3小時，獲得了顯氣孔率為54 、體積密度為1 . 28s cm ~ 3 、抗彎強度為13 . 25mpa的多孔hap人工骨材料。The results show that : the fillers of sio2 based investment consist of sio2, al2o3 and mgo, and the binder is nh4h2po4 for sio2 based investment, the bulk density and the compression strength decrease, the apparent porosity and the thermal expansion increase, when the specimens are heated to 900 ; the fillers of al2o3 based investment consist of al2o3 and mgo, and the binder is nh4h2po4 ; for al2o3 based investment, the bulk density decreases and the apparent porosity increases when the specimens are heated to 900 ; the fillers of mgo based investment consist of mgo and al2o3, and the binder is ca cement ; for mgo based investment, the compression strength decreases and the thermal expansion increases greatly when the specimens are heated to 900
結果表明：氧化硅系包埋料的骨料是氧化硅、氧化鋁、氧化鎂，結合劑為磷酸二氫銨，其900鍛燒后顯氣孔率增加，體積密度下降，耐壓強度降低，熱膨脹增大；氧化鋁系包埋料的骨料是氧化鋁和氧化鎂，結合劑為磷酸二氫銨，其900燒后顯氣孔率增加，體積密度下降，熱膨脹變化不大；氧化鎂系包埋料的骨料是氧化鎂和氧化鋁，結合劑是鋁酸鈣水泥，其900燒后耐壓強度明顯降低，熱膨脹明顯增大。In this paper, the alumina ceramic was prepared under normal pressure and low temperature, the mechanical properties, micromorphology, microstructure of grain boundary and phase composition of the alumina ceramic, and the precision shaping and cold processing of the femoral head were systematically studied ; the effects of the additives, the relation between microstructure and mechanical strength, the sintering mechanism of the material and the influence factors of the structure and properties of the alumina ceramic were discussed also
本文在常壓低溫條件下制備了氧化鋁陶瓷，系統研究了氧化鋁陶瓷材料的力學性能、微觀形貌、晶界顯微結構、相組成和股骨頭的精密成型、冷加工，並討論了添加劑的作用、材料顯微結構與力學強度的關系、材料的燒結機理及影響氧化鋁材料結構與性能的因素。Based on analyzing sintering and infiltration processes, the effect of infiltration temperature on microstructure and properties of the material was studied when the ratio of w - cr, the porosity of green compact and the sintering process of w - cr skeleton were fixed. the differences of microstructure and properties of the composites with different composition were investigated by same sintering and infiltration processes. the composites were prepared in h2, n2, ar and vacuum conditions respectively
基於對wcr cu復合材料的燒結和熔滲過程的分析，研究了cr - w配比、壓坯緊實率、骨架燒結工藝相同的情況下，不同熔滲溫度對材料的組織形貌和性能的影響；研究了燒結-熔滲工藝相同的情況下，不同配比對材料組織和性能的影響；研究了h _ 2 、 n _ 2 、 ar和真空四種燒結氣氛下材料組織和性能的變化。The preparation, mechanical properties of alumina material and machining of femoral head for bioceramic - metal articulated partial hip joint prostheses were studied in this paper, which provided the research results being worth theoretical reference and practical use for the solving of technical problems of sintering and machining of alumina ceramic
本文研究高性能氧化鋁生物陶瓷?金屬配伍型人工半髖關節股骨頭材料的制備、力學性能及假體的成型加工工藝，為解決氧化鋁陶瓷燒結、機加工等技術難題提供具有一定理論參考和實際應用價值的研究結果。分享友人