燒蝕時間 的英文怎麼說

中文拼音 [shāoshíshíjiān]
燒蝕時間 英文
ablation time
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 蝕 : Ⅰ動詞1. （損失; 虧耗） lose 2. （腐蝕） erode; corrode Ⅱ名詞（天體現象） eclipse
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 時間 : time; hour; 北京時間十九點整19 hours beijing time; 上課時間school hours; 時間與空間 time and spac...
  1. It has a good high tenperature flow ability short setting time, rignersintered strcngth and high corrosion resistance

    該產品具有良好的高溫流動性，較短的硬化時間，較高的燒結強度優質的耐侵蝕性能。
  2. Relation between size - uniformity of si nanoparticles and oscillating stabilization time of the mixed region during laser ablation

    激光燒蝕過程中密度交疊區振蕩穩定時間與晶粒尺寸均勻性的關系
  3. Abstract : by means of analysing the difference of fuel feature of organic solid wastes and coal ， this paper discusses low pollution ， low corrosion and high efficiency technology of organic solid waste incineration from several factors including controls of technology ， temperature ， residence time, air ratio and the use of the additives and flue gas

    文摘:通過分析固體有機廢物與煤的燃料特性的不同及其對燃燒的影響，從工藝控制，溫度控制，停留時間選擇，送風控制，添加劑以及煙氣循環使用等方面探討低污染、低腐蝕、高效固體有機廢物的焚燒技術。
  4. The simulations results show that the spoiler is available to make the fuel and the oxidizer coming from the former to stay in the cavity for a long time, to let the fuel and oxidizer mix and burn completely. since there is a high temperature zone forming by vortex in the middle of the motor, it required a restricted thermal protection. the plate with holes decreased the vortex function in the cavity, which could not promote the combustion efficiency, but to decrease temperature in the cavity and be benefit to thermal protection of the wall

    計算結果分析表明:擾流板可以使燃料和氧化劑在擾流腔內的滯留時間加長，促進燃料與氧化劑的摻混燃燒，提高燃燒效率，但由於渦流在發動機的中間部位形成了高溫燃燒區域，致使局部燃料和絕熱層燒蝕速率增大，加大了熱防護的難度;孔板結構減弱了擾流腔內迴流區的漩流作用，不能增加推進劑燃燒效率，但可以使擾流腔內的溫度降低，給壁面熱防護帶來好處。
  5. Abstract : in one sintering plant, its no. 1 wagon tipper ' s track sur face occurred corrosive pitting and stacking only after short application, and th is effect the normal production seriously. in order to diagnose the plastic defor mation of the track surface, we made test and fem analysis to it, found the re ason of failure, and put out improving measure

    文摘:某燒結廠1號翻車機在使用較短時間后，導軌表面出現點蝕和堆邊現象，嚴重影響正常生產.針對這一問題，對導軌表面塑性變形進行了實測和有限元分析，從而找出了故障原因並提出了改進措施
分享友人
分享到 Line

分享到臉書