爐膛構造 的英文怎麼說

中文拼音 [lútánggòuzào]
爐膛構造 英文
hearth construction
  • 膛 : 名詞1. （胸腔） chest; thorax 2. （器物的中空部分） inside cavity; chamber
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 造 : Ⅰ動詞1 （做; 製作） make; build; create; produce 2 （假編） cook up; fabricate; concoct 3 [書面語...
  • 構造 : structure; construction; constructional detail; tectonic; structural; makeup; anatomy; constituti...
  1. The experimentation of cool and hot diagnosis reflected the structure and disposal of combustor, slag bonding and smirch of hearth are the main factors of hearth ' s outlet overheat and output of boiler decline

    冷、熱態診斷試驗反映出爐膛結焦、粘污及燃燒器的結構和布置等因素是造成爐膛出口煙溫偏高，鍋爐出力下降的主要因素。
  2. This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation

    本文針對該鍋爐在實際運行中存在的問題：在額定負荷下，爐膛出口超溫、低溫段過熱器前煙溫高達936 ，遠遠超過815的設計值；噴燃器四周水冷壁結焦嚴重，過熱器管壁溫度超標，無法帶上額定負荷；甚至有時因燃煤質量的變化，必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中，燃燒器的結構、布置，水冷壁的粘污、結垢，過剩空氣系數、一次風溫、煤種及其濃度變化等許多因素都會偏離鍋爐的設計工況，從而影響爐內的傳熱和燃燒，造成爐膛出口超溫、水冷壁結渣等問題。
  3. The reform scheme of no. 1 boiler in fengtai company is confirmed on the basis of cold / hot tests, theoretical discussions and calculations. in the process of field retrofit, it is indicated in the operation of the improved furnace that without the change of furnace structure, the transform of the burner angle has shrunk the tangential diameter and prevented flames burning on furnace walls, and the burning state of furnace has been bettered, simultaneously, lowering the slagging wi in furnace, thus laying sol id foundation for the safe and economic operation of generating units. wuyanrong ( power plant thermal power engineering ) directed by prof

    本論文通過冷、熱態試驗，經過論證和計算，確定了豐泰公司~ # 1爐燃燒器的改造方案，並進行了現場改造，改造后實際運行狀況表明：在無法改變爐膛結構的情況下，改變燃燒器角度，縮小切圓直徑，使火焰不貼壁，改善了爐內燃燒工況，同時降低了鍋爐結渣的程度，為機組的安全經濟運行奠定了必要的技術基礎。
  4. These results show that since the existent defects of combustion device structure and its hypothetical circle of contact, these make a poor primary and secondary wind rigidity in operation and a too big actual circle of contact. in addition, the coal used is extreme prone to burn and reside in boiler. under such a condition, the coal powder ignites earlier in a short time and short distance when it leave the jet - combustioning device, and splashes the water cooler, eventually this results in a burned coal residue in boiler

    針對宏偉熱電廠410t / h燃煤鍋爐嚴重結渣問題，對燃煤的結渣性、爐內溫度工況及空氣動力工況等進行實驗研究，由於燃燒器結構和假想切圓選擇的缺陷，使得鍋爐在正常運行時，一、二次風剛性較差，實際切圓過大，加上目前燃用煤質屬于極易燃、易結渣煤質，致使煤粉在離開噴燃器很短的時間、較短的距離內開始著火，並沖刷水冷壁，最終造成爐膛結渣。
分享友人
分享到 Line

分享到臉書