環向間隙 的英文怎麼說

中文拼音 [huánxiàngjiānxì]
環向間隙 英文
radial clearance
  • 環 : Ⅰ名詞1 （環子） ring; hoop 2 （環節） link 3 （姓氏） a surname Ⅱ動詞（圍繞） surround; encircle;...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 隙 : 名詞1 （縫隙; 裂縫） crack; chink; crevice 2 （空閑） gap; interval 3 （漏洞; 機會） loophole; op...
  • 間隙 : （空隙） interval; gap; freedom; space; [機械工程] clearance; separation; stricture; clear; inter...
  1. The derivation of the leakage flow rate formula of the special annular clearance between the piston and cylinder under condition of variable viscosity in the axial piston pumps was carried out. at same time, considering the questions of the eccentricity and the variable sealing length of piston friction pair, the modified coefficient of the calculation formula of the flow - rate of the leakage was given

    在變粘度、柱塞偏心以及變密封長度條件下，對軸向柱塞泵中柱塞與缸孔之間的特殊圓環縫隙的泄漏流量公式進行推導，得到了該計算公式的修正系數； 6
  2. Meanwhile it retains evenness on lift force to prevent leakage of residue that is caused by installation clearance error or changes in welding criteria, flow off molten iron as well as break - over welding, so that the ideal fosion depth and finishment have been fulfilled

    在需原動力的條件下，該機利用彈性夾角變化，隨著筒體轉動，使墊層焊劑始終緊貼筒體外側環向焊接區，並保持托力均勻防止因裝配間隙誤差或焊接規范變化而引起漏渣，鐵水下淌及焊穿現象，達到理想的熔深度和光潔度。
  3. In view of the problems in the design of the large andmedium - sized indoor substations built by guangzhou power bureau in recent years, points for attention in the design of indoor substations are expounded in terms of ventilation, cable channel, reservation of hangers and space for transportation and installation, ground wire, lighting for the whole substation, etc

    僅僅推力頭軸、孔存在間隙時，推力頭其它零件製造質量與安裝質量達到設計要求，是不會影響精確徑向定位的.爾王莊泵站9機組出現的環鍵與平鍵斷裂情況，可能不是由軸、孔間隙過大引起，而是其它尚未查明的原因
  4. To ensure the charging pump working reliably, the following measures should be adopted : ( 1 ) adopting modified circular casing to reduce the radial force of the impeller and decrease the seal clearance ; ( 2 ) using radical ribs on impeller and helical sealing on shaft to realize minor pressure differential ; ( 3 ) using back pressure stuffing box to ensure sealing under small packing force ; ( 4 ) adopting self - lubricant flexible graphite stuffing for absorption of solids entering in the graphite in case of leaking

    為確保灌注泵可靠工作，提出改進措施： （ 1 ）採用改型環形泵體降低葉輪的徑向力，減小軸封間隙，抑制泄漏； （ 2 ）採用背葉片降低葉片根部壓頭，獲得微壓，使軸封兩端承受較小壓差； （ 3 ）採用螺旋密封降低軸封兩端壓差，在保持微壓的同時避免出現負壓，密封效果更好； （ 4 ）採用反壓式填料密封結構，在很小的壓緊力下，即可保證密封； （ 5 ）採用具有潤滑功效的柔性石墨填料，即使發生軸封泄漏，進入石墨內部的固相顆粒也將隨著石墨的消耗而被鉆井液吸收。
  5. It was found that the ultra - fine powder can flow smoothly in a spouted bed with a draft tube under some sorts of design parameter and operating condition, thus a new effective method to improve fluidization quality of the ultra - fine powders is obtained ; at higher supplied gas velocity, an increase in the solid circulation rate is observed ; the extent of the distance between the nozzle and the draft tube inlet result in the promotion of the solid circulation rate ; the solid circulation rate increase with increasing the draft tube diameter or the bed mass ; the gas bypassing is nearly zero in the present work ; and the solid flow in the annulus is observed as a moving bed

    結果表明：在一定的床層結構和操作條件下，超細粉可以在導向管噴動床中實現平穩流化，從而為改善超細粉的流化質量提供了一種有效的新方法；固體循環速率與噴動氣流量、導向管直徑、導向管底部與噴嘴出口間距以及床層裝填量成正比；氣體則基本上不存在「旁路」現象；環隙區中的顆粒流動表現為一移動床特徵。
  6. The calculation to the eddy current on the contact surface and axial magnetic field of contact surface and center surface of contact gap are carried out while the current is at zero. after the iron core of ring type is put in, the eddy current on the contact surface will be increased, the axial magnetic field that the eddy current creates will be also increased

    對電流過零時觸頭表面的渦流和觸頭表面及觸頭間隙中心平面上的縱向磁場進行了計算，加入圓環型鐵芯后觸頭表面的渦流增大，渦流產生的縱向磁場增大，在鐵芯中開槽后渦流的平均水平降低，縱向磁場平均值降低。
分享友人
分享到 Line

分享到臉書