環形聯結器 的英文怎麼說

中文拼音 [huánxíngliánjiēqì]
環形聯結器 英文
ring type hitch
  • 環 : Ⅰ名詞1 （環子） ring; hoop 2 （環節） link 3 （姓氏） a surname Ⅱ動詞（圍繞） surround; encircle;...
  • 聯 : Ⅰ動詞（聯結; 聯合） unite; join Ⅱ名詞（對聯） antithetical couplet
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 環形 : annular; ringlike; ring form; bight; annularity環形癌 annular carcinoma; 環形電路 [訊] loop circu...
  • 聯結 : bind; tie; join; jointing; anastomosis
  1. There is difference frequency measurement requirement for every part of pid regulating, difference between dynamic quality and static quality in response time and accuracy. according to these, it use the interrupt functions and high - speed counter of the simens s7 - 200 plc cpu226 basic unit and some peripheral circuit to measure frequency ; in software designed, the procedure frame of hydraulic - turbine governor and disperse process of parallel pid are analyzed, an improved pid algorithm is adopted to realize a pid regulation mode with variable structure and parameters ; the mechanical liquid - pressure system of the hydraulic - turbine governor is with electric - hydraulic converter unit of step motor. according to the drive character of five phase of response step motor, a variable frequency regulated voltage driver unit is designed in order to realize interface between plc and driver of step motor

    本文利用s7 - 200plc自身的特點設計了頻率測量單元，根據pid調節各個環節的特點，以及調速器動態特性、靜態特性對頻率測量的實時性和精度要求的不同，利用s7 - 200plc基本單元中內置的高速計數器以及相應的外圍放大整形、分頻電路，實現了水輪發電機組頻率的測量；在軟體上，對微機調速器的整個程序框架、並聯pid的離散化過程進行了分析，選用改進的pid演算法實現了變參數、變結構的pid調節模式；調速器的機械液壓隨動系統具有步進電機電液轉換元件，採用五相反應式步進電機，根據其驅動特性設計了變頻調壓驅動器，實現plc與步進電機驅動器之間數字介面。
  2. In this paper, the microstructure changes of polypropylene induced by a complex combination of shearing, compression, stretching and friction actions during single pan - milling or co - milling with iron, uhmwpe and waste tire rubber chips ( wtr ) were studied and the stress induced effects were revealed. the structure and morphological development of iron particulates and wtr during pan - milling and co - milling with polypropylene were also characterized. the properties of pp / fe, pp / wtr and pp / wtr / fe composites prepared through pan - milling techniques were investigated

    本文利用磨盤型力化學反應器對被碾磨材料施加強大的剪切、環向應力、擠壓、拉伸和摩擦作用，研究聚丙烯碾磨和共碾磨粉碎過程微觀形態結構和性能的變化，以及聚合物在碾磨過程中呈現的力化學現象，並將其應用拓展至金屬、橡膠等體系，研究碾磨粉碎在聚丙烯鐵超微粉體的制備、高交聯密度彈性材料廢舊輪胎橡膠（ wtr ）的超微粉碎，以及pp fe ， pp wtr材料的性能與碾磨作用的關系。
  3. By combining the system developing levels with the application environment, the redundancy level was positioned in the model - level redundancy, a / d connected in series with the master as the redundant unit, the bi - processor models drive on outer model

    結合系統開發層次與使用環境，將冗餘級別定位於模塊級冗餘，提出了以a d與主機串聯形成的處理器模塊為冗餘單位、雙處理器模塊共同驅動一套外設的模型。
  4. Hardware interface and theory of digital controller and velocity output are emphasized in hardware design section ; pwm wave producing module closely related chip structure is emphasized in software design section

    硬體設計部分重點介紹了數字控制器和速度輸出環節的硬體介面和工作原理；軟體設計部分重點介紹了與晶元硬體結構緊密聯系的pwm波形產生程序模塊。
分享友人
分享到 Line

分享到臉書