環面蝸桿傳動 的英文怎麼說

中文拼音 [huánmiàngǎnzhuàndòng]
環面蝸桿傳動 英文
enveloping worm drive
  • 環 : Ⅰ名詞1 （環子） ring; hoop 2 （環節） link 3 （姓氏） a surname Ⅱ動詞（圍繞） surround; encircle;...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 蝸 : 名詞[動物學] （蝸牛） snail
  • 桿 : 桿名詞（桿子） pole; staff
  • 傳 : 傳名詞1 （解釋經文的著作） commentaries on classics 2 （傳記） biography 3 （敘述歷史故事的作品）...
  1. The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly

    研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。
  2. Planar double - enveloping worm gearing terminology

    平面二次包絡環面蝸桿傳動術語
  3. Planar double - enveloping worm gearing accuracy

    平面二次包絡環面蝸桿傳動精度
  4. Analyses on the length of contact lines and the contact area of a double enveloping wormgearing with planar generating surface

    平面二次包絡環面蝸桿傳動接觸狀況分析
  5. On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs

    考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示
  6. The meshing efficiency of the drive is studied and analyzed in theory. the different formulas for meshing efficiency of drive are introduced on different conditions when stator or worm is fixed respectively

    從理論上研究分析了滾錐齒超環面行星蝸桿傳動的嚙合效率，推出了在定子固定和蝸桿固定兩種情況下滾錐齒超環面行星蝸桿傳動嚙合效率的計算公式。
  7. It can be regard as the theoretical basis to optimize the drive. according to the gear meshing theory, the meshing equations, the contact line equations and tooth profile equations are given. it gives a base for 3d modeling the drive

    按照齒輪嚙合理論，推導出了滾錐齒超環面行星蝸桿傳動的接觸線方程、嚙合方程及各輪輪齒的齒面方程，為滾錐齒超環面行星蝸桿傳動的三維建模奠定了基礎。
  8. On the base of deducing meshing theory, by simplifying the parameters and using software, the 3d model of the rolling cone - type toroidal drive is given. and the parametric models are realized. the assemble chart of drive is given

    在嚙合理論推導的基礎上，通過對滾錐齒超環面行星蝸桿傳動的各參數進行簡化處理，利用計算機軟體對滾錐齒超環面行星蝸桿傳動進行了三維實體參數化建模，實現了模型的參數化，給出了該傳動的裝配圖，並進行了動態模擬。
  9. By means of the optimization method - punishing function method and taking the sum of the planet gear radius and center distance as the target function, the parameters of drive are optimized. by using the optimization program, the initial serial studies of drive are completed, the best serial parameter value of the drive is given

    採用外點罰函數優化方法，通過取行星輪半徑和中心距之和作為優化目標函數，對滾錐齒超環面行星蝸桿傳動進行了參數優化，運用此優化程序，初步完成了對該種傳動的系列化研究，給出了傳動系列的最佳參數取值。
  10. The process has an advanced principle. the involute hourglass worm drive can realize the design machining of gear form and direction, and the internal meshing honing gear has high efficiency. this process has all merits mentioned above, and also has the advantages of quality stability, high productivity for rude and finish machining

    該工藝原理先進，它集有利於實現齒形、齒向設計加工的漸開面環面蝸桿傳動與高效的內嚙合珩齒的優點與一體，對齒輪的粗、精加工都有質量穩定、生產效率高的優點。
  11. The motion of the drive is also demonstrated. the paper mainly concludes the following works : the paper introduces the meshing theory of rolling cone - type toroidal drive and the motional relations of all parts, gives the formula of transmission radio. the relation between tooth numbers and helix angle of every parts is found out, and the assemble relation among all the parts is also given

    本論文主要包括以下內容：介紹了超環面行星蝸桿傳動的傳動原理及各構件間的運動關系，分蝸桿固定和定子固定兩種情況，給出了這種新型傳動的傳動比計算公式，得出了各輪齒數與計算圓處螺旋升角間的關系和各構件間的裝配關系，從而為該傳動的優化打下理論基礎。
  12. The keep with bounds were be fuzzy by the method of oblige line. this program not only has been used to optimization the pdew but also could used to control the fuzzy factor that could change the strength of fuzzy. when the fuzzy factor equal to one, the fuzzy optimization program could change to a general optimization program

    該優化設計程序不僅適應于平面二次包絡環面蝸桿傳動的模糊優化，而且可以改變模糊因子的大小，控制約束條件的模糊程度，甚至變換為常規的優化設計程序，程序的適用范圍較廣。
  13. Larger loading capacity under the same specification ; easily establishing lubricant oil film, smaller friction coefficient, higher transmission efficiency, saving energy ; highest accuracy up to grade 3 of din standard ; smoother functioning, lower noisiness and longer service life

    平麵包絡環面蝸桿與普通圓柱蝸桿傳動相比具有更大的承載能力，易於建立動壓油膜摩擦系數小，傳動效率高節省能源具有可磨削性，能達到din標準三級，面粗糙度優于ra0 . 4而且具有運行平穩噪音低壽命長等優點。
  14. Planar double - enveloping worm gearing geometrical data symbols

    平面二次包絡環面蝸桿傳動幾何要素代號
  15. The states of motions and victories and forces of the worm engaging point were been analysis. the motions and forces of the worm engaging point have been initiate by the program with matlab. the 3d motions of plane double enveloping worm has been emulated with solidege and flash

    應用solidege三維實體造型軟體，進行平面二次包絡環面蝸桿傳動的運動狀態的動態模擬，模擬了平面二次包絡環面蝸桿傳動的運動狀態，再現了蝸桿嚙合的運動狀態的模擬。
  16. In order to improve the level of automation design for the plane double - enveloping worm - gear reducer, this paper developed a cad prototype system for the reducer. the cad prototype system included two parts : 1 ) the optimization design software of the parameter for the worm gear was written by visual basic 6. 0 ; 2 ) the parameter modelling software for the reducer was developed by using autocad2000 / vba

    為了提高平面二次包絡環面蝸桿減速器的自動化設計水平，針對目前國內還沒有平面二次包絡環面蝸桿減速器的計算機輔助設計軟體這一現狀，本文研究和開發了平面二次包絡環面蝸桿減速器cad原型系統：用當今比較流行的可視化軟體visualbasic6 . 0開發專門用於平面二次包絡環面蝸桿傳動的優化設計系統；用autocad2000 / vba開發的中心距從80mm到710mm的平面二次包絡環面蝸桿減速器的參數化建模軟體系統。
  17. Main products : standard series of plane enveloping toroidal worm tp worm for short reducers and worm gear sets. center distance is a loo - 500mm

    標準系列平麵包絡環面蝸桿減速器及其蝸桿副：中心距a 100 - 500mm ，傳動比10 - 63按用戶要求設計製造非標平麵包絡環面蝸桿減速器及其蝸桿副：中心距： a
  18. Abstract : calculation of the length of contact lines of a double enveloping wormgearing with planar generating surface and finding out the size of contact area are th e foundation of strength analyses of wormgearing

    文摘:計算平面二次包絡環面蝸桿副的接觸線長度和了解蝸輪齒面接觸區域的大小是蝸桿傳動強度分析的基礎。
  19. Design of multi - target optimization for planar quadratic ring eveloped worm gear drive

    平面二次包絡環面蝸桿傳動多目標優化設計
  20. This thesis reviewed the mesh theory of plane double - enveloping worm gearing : the equations including the first enveloping equation, the second enveloping equation, contact line equations of the first enveloping and the second enveloping, boundary equations of the first enveloping and the second enveloping, the equations of relative velocity and absolute velocity

    本文介紹了平面二次包絡環面蝸桿傳動的嚙合原理基礎：第一次包絡嚙合方程和第二次包絡嚙合方程，相對速度、相對角速度方程，第一次包絡的接觸線方程，第二次包絡的接觸線方程，以及第一次、第二次包絡的一界線方程和二界線方程。
分享友人
分享到 Line

分享到臉書