直徑損失 的英文怎麼說

中文拼音 [zhíjìngsǔnshī]
直徑損失 英文
loss of working diameter
  • : Ⅰ形容詞1 (成直線的; 硬挺的) straight; stiff 2 (跟地面垂直的; 從上到下的; 從前到后的) erect; v...
  • : Ⅰ名詞1 (狹窄的道路; 小路) footpath; path; track 2 (達到目的的方法) way; means 3 (直徑的簡稱...
  • : Ⅰ動詞1 (減少) decrease; lose 2 (損害) harm; damage 3 [方言] (用尖刻的話挖苦人) speak sarcas...
  • 直徑 : diameter; diam
  • 損失 : 1. (失去) lose 2. (失去的東西) loss; wastage
  1. The position and size of the monochromator, focusing curvature radii and tilting angles of the germanium focusing monochromator under different different take - off angle, size and divergency of the second collimator and intensity loss due to the use of it were determined. the neutron flux at different wavelength, under different reflection and take - off angle of the monochromator and divergency of the first collimator, were given. the simulation on the aperture used for limiting beam size in front of the sample showed that, smaller the size of the aperture and further the distance from the aperture to the sample, greater the loss of the intensity and more serious the spread of the beam along vertical direction at the sample position which makes the practical sampling volume greater than expected

    用蒙特卡羅模擬方法對中子應力衍射譜儀的設計方案進行了優化研究,提出了一系列可供參考的數據:確定了單色器的位置、尺寸、垂聚焦單色器在不同起飛角下的聚焦曲率半和傾角;討論了第二準器的尺寸和發散,以及使用第二準器造成的強度;給出了在不同單色器反射面、起飛角、中子波長和第一準器發散度的情況下樣品處的中子注量率,以及多種組合情況下譜儀的解析度曲線;對限束方孔的尺寸、距離樣品遠近對強度和測量中的影響做了深入研究。
  2. Full - bore : full - bore straight - through type with connection between valve and pipeline or straight pipe, equal sectional area and " 0 " loss of flow

    全通:全通通式,閥門與管道或管連接相通,截面積相等,流量為「 0 」 。
  3. Agricultural futures have long been a way to limit risk with crop prices. futures trading can help protect against losses. companies also buy futures to guarantee costs for materials

    農業期貨一以來都是降低農產品風險的一個途。期貨交易有助於防止的發生。公司也通過購買材料期貨來保本。
  4. Not only does slump loss influence the effect, it constrains the transportation distance and pumping height and distance but also, and these will make the construction harder. and if slump loss is too much, it will be difficult to cast, and these will be such defects as honeycombs and pothotes, and they will reduce the quality of construction

    坍落度不僅接影響到外加劑的使用效果,還大大制約了攪拌站的服務半以及泵送的高度和距離,給施工生產帶來很多不便,另外,坍落度過大還會造成澆築困難,導致混凝土中產生蜂窩、孔洞等缺陷,嚴重影響工程質量。
  5. There is a part of beam loss during the course as the neutralization of high - energy particles dragged from the ion source, the deflexion of charged particle on the beam stream and the scraped beam of exceeding beam waist and low density. it is necessary to analyze the beam loss and bring forward a rational project for absorbing beam stream

    將離子源引出的高能粒子進行中性化,再偏轉掉束流中的帶電粒子,將超過束腰半、密度較小的束流削除,在此過程中有一部分束流,它接影響加熱功率的因素,因此,對束流進行了分析,對束流的吸收提出了吸收方案。
  6. The theorys and the experiments proved that the high _ press direct in _ cylinder injection is one of the effective ways to solve the fuel escapes unburned

    理論和實驗證明,缸內高壓接噴射是解決二沖程汽油機燃油短路的有效途之一。
  7. The bigger the diameter, the high the heat efficiency, but the weak the temperature increasing ability, length has less effect on the heat efficiency, tilt angle has less effect on the flow field and temperature field while it is larger than 30 degree, vacuum degree and emissivity have great effect on the flow field and temperature field while there is a great temperature difference between the liquid in the tube and the surroundings, the furring has less effect on the heat transfer but should be cleaned up in 3 - 5 years because of poor water quality, the higher the solar flux or the more the temperature difference between the liquid and the surrounding, the more the heat loss and the lower the heat efficiency

    分析了各種因素對太陽能真空集熱管流場和溫度場的影響。越大,熱效率越高,但升溫能力弱;長度對熱效率影響不大;傾斜角度大於30后,自然對流已經能夠充分進行,考慮以能夠吸收到最大太陽輻射為主;真空度和發射率對熱效率和溫度場影響很大,尤其是在介質溫度與環境溫度差異比較大時;水垢對傳熱影響較小但由於水質的問題應該被3 5年清洗一次;太陽輻射強度越大,介質溫度與環境溫度差異越大,熱越大,效率越低; 4
  8. Therefore, it is desirable to investigate and enhance the mechanical property of silicon single crystal. in this paper, the fracture property of czochralshi ( cz ) and nitrogen - doped silicon ( ncz ) were investigated at room temperature by three - point bending method

    尤其在當今隨著矽片不斷增大的情況下,提高矽片的機械強度,減少矽片傷、翹曲、位錯及其滑移等帶來的變得十分重要。
分享友人