相交軸 的英文怎麼說

中文拼音 [xiāngjiāozhóu]
相交軸 英文
concurrent axes
  • 相 : 相Ⅰ名詞1 （相貌; 外貌） looks; appearance 2 （坐、立等的姿態） bearing; posture 3 [物理學] （相位...
  • 交 : Ⅰ動詞1 （把事物轉移給有關方面） hand over; give up; deliver 2 （到某一時辰或季節） reach （a cert...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 相交 : 1 （相交叉） intersect: ab與cd兩直線相交於e點。 the lines ab and cd intersect at e ; the line ab ...
  1. An axial electron pair meets at right angles with 3 neighboring pairs.

    軸向電子對與三個相鄰的電子對相交成直角。
  2. One new type double backspin rotor type sand mixing machine passes technique appraisal of qingdao tianheng machinery co., ltd. this machine adopts double rotor configuration researched internationally ; the rotor is installed on different output axis of same reducer, which produces comparative cross cutting speed by using rotors with different speed that makes sands get strong cutting and friction force. therefore, it can reduce clay and quicken sand mixing

    一種新型雙逆轉子式混砂機在青島天恆機械有限公司通過技術鑒定，該機採用國際首創的雙轉子結構，其轉子安裝在同一減速器的不同輸出軸上，利用兩個軸的不同轉速使轉子間產生相對交叉剪切速度，使砂子受到的沖剪及搓擦力加強，從而減少粘土團，加快砂子的混合。
  3. So far, the main frame of the conjugation of betrand are established, on the basis of which, it is given that the primary condition the directrix line must be satisfied, the relative curvature of the conjugating surfaces, the relations between non - interventional condition and curvature axle of the directrix line, and so on. the transmission of normal circular - arc gear is a typical bertrand conjugation. in order to promote the transformation from theory to technology, the general principle of this kind of transmission is studied

    為了使研究更加貼近於工程，便於解析處理，提出準面的概念，並確立由準面到準線的研究路線，給出了各種傳動形式下準面與準線的具體特徵，證明了共軛準面上兩準線的誘導測地曲率等於零的這一不干涉條件，進而指出，當準面為平行軸和相交軸傳動的節曲面時，不干涉條件自然滿足。
  4. All planes perpendicular to the solar axis intersect the solar sphere along circles of latitude.

    所有垂直於太陽軸的平面和太陽球面相交成緯度圈。
  5. Earlier in this section, we noted that the tails of the normal distribution approach but never touch the horizontal axis.

    本節前面已經指示，正態分佈的兩個尾端趨近於橫軸，但永遠不與橫軸相交。
  6. All of the hydraulic structures are arranged in the right bank and four underground seepage tunnels are arranged parallel in horizon, and the axle wires intersect with syncline axis almost perpendicularity, and with rock formation obtusely. complex underground tunnels are formed under such formidable conditions, and each of seepage tunnels crosses nuclear of syncline and comes up against interlaminar sharing disturbed belt at different footage

    四條引水發電隧洞在平面上平行布置，軸線方向與本區構造線方向近於垂直，與巖層走向大角度相交，構成一復雜地下洞室群，並在不同洞段通過沙金壩向斜核部，且遭遇多條層間剪切錯動帶。
  7. Obtain these chief research achievements. ( 1 ) the method of hydraulic fracturing, kaiser effect experiment and the finite element numerical simulation computation results, the direction of maximum horizontal principal stress intersect the small - angle of tunnel axial line, it is favorable to the stability of tunnel peripheral rock ; according to the test rust of field stress - relief method, at the present time, zhe gu mount tunnel have n ' t access to high crustal stress site, maximum principal stress magnitude is 17mpa ~ 20mpa

    主要獲得以下研究成果： （ 1 ）綜合水壓致裂法、室內巖石kaiser效應試驗和有限元數值模擬計算研究成果，最大水平主應力方向與隧道洞軸線小角度相交，對隧道圍巖穩定性有利；根據現場應力解除法測試結果，目前鷓鴣山隧道尚未進入高地應力段，最大主應力量級為17mpa 20mpa 。
  8. Empowered by robust technological strength and sound development platform, we produce cdqc ua series, m2ua series and uabp series three - phase universal frequency conversion variable speed motors, ubpt series three - phase main shaft three - phase frequency conversion variable speed motors, ubps series three - phase main shaft long and thin motors, ubpd series special motors for washing machines, ubpg series three - phase main shaft frequency conversion high speed motors, ut series special motors for oil pumps ， sks ac servo motors, fd series special motors for escalators, ta series three - phase permanent - magnet synchronous motors, lk series three - phase asynchronous motors and tp series three - phase permanent - magnet frequency conversion variable speed motors

    德驅馳憑借其雄厚的技術實力和良好的開發平臺，推出了「德驅馳」牌ua系列、 m2ua系列、 uabp系列三相通用變頻調速電機、 ubpt系列三相主軸變頻調速電機、 ubps系列三相主軸低慣量電機、 ubpd系列水洗機專用電機、 ubpg系列三相電主軸變頻高速電機、 ut系列油泵專用電機、 sks交流伺服電機、 fd系列扶梯專用電機、 ta系列三相永磁同步電機、 lk系列三相異步電動機、 tp系列三相永磁變頻調速電機。
  9. As a consequence, the mmf due to the armature current is along the aixs midway between the two adjacent poles, called the quadrature ( or q ) aixs

    因此，由電樞電流所產生的磁動勢沿著相臨的兩個磁極，並稱為正交軸。
  10. The algorithm, basing on convolution filtering technique and the fringes " gray values max - min distribution, can automatically and accurately carry out space frequency spectra shifting without spectra analysis and spectrogram in the technique of phase method of projected grating for 3 - d object shapes measurement. the new algorithm makes image processing much caster and the technique of object shapes measurement more automated. the phase error caused by filtering and the crossed - optical - axes geometry setup is also discussed

    本文採用投影光棚相位法和數字卷積濾波技術：根據柵線的條紋灰度值分佈具有極大極小分佈的特性，提出卷積濾波形貌光學自動檢測的圖像處理方法，有效地實現了頻譜自動移位，從而進一步提高了圖像處理的速度和形貌測量技術的自動化程度；同時對採用兩光學主軸相交，且非遠心投影系統所產生的誤差進行了分析，並提出了修正方法。
  11. Gear pair with intersecting axles

    相交軸齒輪副
  12. The spiral bevel gears are widely utilized in the intersecting axis transmission with its transmitting smoothly and higher strengthen, such the machinery as transports, machine tool, helicopter, mining and so on

    弧齒錐齒輪在相交軸傳動中，由於傳動平穩、強度高而被廣泛應用於交通運輸、機床、直升飛機、礦山機械、工程機械等工業產品。
  13. Then the non - interventional condition is that the relative geodesic curvature is zero. furthermore, for the transmission of the parallel or crossing axles, if the datum surface is the pitch one, the non - interventional condition is naturally satisfied

    考慮到平行軸的法向圓弧齒輪傳動已臻成熟，論文重點研究了相交軸與交錯軸條件下法向圓弧齒輪傳動的基本方案。
  14. 4. to get the motor ' s performance by calculation with known formulas, as a result an adjustment for the motor ' s configuration can be practised. when a combined method of altering the length of armature, the number of turns in the winding and the dimension of permanent magnet is used. 5. to get the motor ' s performance when it is driven by the power converter. finally, the calculated data are compared with the experimental measurements, so as to verify the rationality and reliability of the method

    Q採用數值分析直軸負載磁場和交軸電樞反應磁場的方法來計算，得到較為準確的結果；根據電機工作特性的計算公式計算電機性能，由計算結果調整電機的結構，而調整工作使用改變電機鐵心長度、繞組匝數和永磁體尺寸相結合的方法，這樣可以得到較為理想的結果；對變頻電源供電時電機的工作特性進行計算，以檢驗其變頻時的性能。
  15. Geometry analysis on the ultraright point of intersection curve of two cones with intersectant axes

    關于軸線相交的兩圓錐相貫時最右點的解析分析
  16. This paper brings forward and proves a rapid interval test for resolving intersection tests between bounding volumes. it determine two bounding volume do not overlap by checking if one of their bound intervals on direction axis defined by the fix direction set does not overlap

    文中提出並證明了一種快速區間測試法以解決兩個固定方向凸包包圍盒間的相交測試問題，通過查找兩個包圍盒在由固定方向集合所定義的方向軸上的范圍區間是否存在不重疊的情況，來判斷它們是否不相交。
  17. Dd862 and dd862a single phase electic meter are in duction meter. it is used in calculating 50hz single - phase ac active electrical energy. it is compaosed of electromagnetic element. moving disc, bearing, damping magnet steel, counter and regulator and regulator equipment. the meter has high precision, high over - load, long lifetime and so on features

    ： dd862型和dd862a型單相電度表是感應式儀表，用於計量器頻率為50hz的單相交流有功電能。它主要由電磁元件轉動圓盤軸承阻尼磁鋼計度器和調整裝置等組成，本表具有高精度高過載長壽命等特點。
  18. In underground engineering, the cavity axis should be designed to intersect fractures with large - angle ( 90 ) as it traverses fault and joints

    摘要在地下工程中，當洞室穿越斷層、節理等破碎帶時，應盡可能使洞軸線走向與破裂面的走向呈大角度相交（ 90 ） 。
  19. At last, the paper did a detailed analysis on the measurement principle, measurement method, measurement data and measurement precision. explicit the purpose and meaning of measuring the static precision of turn table. after comparison the author decided the reasonable and fitting method to measure the turn table ’ s static precision which include turn table ’ s angular error, intersection and perpendicularity

    最後，本文將重點放在了轉臺機械臺體的靜態精度測試方面，明確對轉臺機械臺體靜態精度測試的目的，指出靜態精度測試包含的三個內容，即轉臺的回轉精度測試、軸系相交度測試和軸系垂直度測試。
  20. There is short of specific and simple calculating method to obtain the cavity axis ' orientation, especially for the rocks with many fractures

    然而如何設計洞室軸線走向與破裂面走向大角度相交，一直缺乏具體而簡易的計算方法，尤其在破裂面較多且產狀明顯不同時，這個問題更為突出。
分享友人
分享到 Line

分享到臉書