相對耐磨性 的英文怎麼說

中文拼音 [xiāngduìnàimóxìng]
相對耐磨性 英文
relative wear resistance
  • 相 : 相Ⅰ名詞1 （相貌; 外貌） looks; appearance 2 （坐、立等的姿態） bearing; posture 3 [物理學] （相位...
  • 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
  • 耐 : 動詞（受得住; 禁得起） be able to bear or endure
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 相對 : 1. （面對面） opposite; face to face 2. （非絕對的） relative 3. （比較的） relatively; comparatively
  • 耐磨 : abrasion resistant; anti friction; wear resistant; wear resisting; wearproof耐磨材料 high abrasiv...
  1. Standard test method for relative resistance to deep abrasive wear of unglazed ceramic tile by rotating disc

    使用轉盤的無釉陶瓷磚相對深層耐磨性的標準試驗方法
  2. Products function : put our “ sun shine ” brand carbon steel fiber evenly seep into concrete to form steel fiber reinforced concrete and it can decrease the thickness of reinforced concrete by half, it not only shorten the project time, save the material and manpower expense, bring distinct economic benefit, but also increase the performance of crack resistance, percussion resistance, tensile strength, bend resistance. scosspr resostamce amd wear resistance of the reinforced base materials. if the weight ratio of 2 % steel fiber seep into the concrete, it can solve the brittleness problem of the concrete, in the condition of 60 % ralative air humidity, after 21days air - dry, even 520 days air - dry, it ' s difficult to find any crack by eyesight, the bend resistance for the steel fiber concrete is 140 times stronger than the concrete without steel fiber, the capability of impact resistance increase 10 times

    產品功能：將本公司「雙興」牌碳鋼纖維系列產品均勻地摻入混凝土中，形成鋼纖維增強混凝土，可使工程中鋼筋混凝土的施工厚度降低一半，不僅縮短了施工工期，節省了材料和人工費用，帶來顯著的經濟效益，且增強了基體的抗裂、抗沖擊、抗彎、抗剪、耐磨擦等性能，如摻入本公司2 %鋼纖維的混凝土，不僅解決了混凝土的脆性問題，在空氣相對濕度60 %的條件下風干21天後，甚至在風干520天，肉眼很難發現裂縫，摻入鋼纖維后的增強混凝土比不摻鋼纖維的混凝土抗彎強度提高140倍，耐沖擊荷載提高10倍。
  3. However the microstructures of the reaction existed before the heat treatment remained untouched. the heat treated fe - cu - c alloy - based composite sintered at 1100c was found to be a kind of ideal wear resistant material

    1100燒結的fe - cu - c基復合材料進行熱處理后可以得到既具有良好的強度性能，又具有優良耐磨性的相對理想耐磨材料。
  4. From the viewpoint of the characteristics of two - phase liquid sand slurry wear, combined with the examination and study on easily damaged workpieces, the wear failure ' s basic rules are pointed out, of the pump shell and the cutter - piece on service, and the general principles of material wear - resistant designs put forward. the sand slurry abrasion tester has been designed and developed which can simulate general dredging conditions. summarized and presented are the position - exchange measuring method of sand slurry abrasion test and the experiment specification of sand slurry wear test of dredging conditions

    文中系統論述了作者在疏浚工況泥沙磨損機理及其耐磨新材料課題研究中的工作成果，主要研究內容和創新點如下：總結分析了磨損研究動態和提高材料耐磨性的方法；從兩相流泥沙磨損的特點出發，結合對失效易損件的考察研究，分析指出了現役泥泵殼和絞刀片磨損失效的基本規律，提出了材料耐磨損設計的基本思想；設計研製了能模擬疏浚工況的泥沙磨損試驗機，總結提出了泥沙磨損試驗換位測試法和疏浚工況泥沙磨損試驗規范。
  5. Test method for relative abrasiveness of synthetic turf playing surfaces

    人造草皮運動場表面相對耐磨性的試驗方法
  6. Standard test method for relative abrasiveness of synthetic turf playing surfaces

    人造草皮運動場表面相對耐磨性的標準試驗方法
  7. The vc - fe surface composite shows high wear - resistance, it ' s wear - resistance is 4. 20 times as that of chilling respectively. with the content of v increasing, it ' s rigidity and wear - resistance increases continually. more vc grains gained, and well distributed, better wear - resistance the vc - fe surface composite will show. ( 7 ) surface cermet composite was formed by the means of cast - sintering technique, with the help of adding wc grains and the quantity of heat sent out from the reaction v + c vc, the carbide cermet quality percent exceeds 60 %

    在重載干滑動摩擦條件下， vc一fe表面復合材料顯示了很高的耐磨性，其相對耐磨性是可淬硬鑄鐵的4 . 2倍:隨著含v量的增加， vc一fe表面復合材料的鑄態硬度和耐磨性不斷提高， vc顆粒越多，分佈越均勻，表面復合材料的耐磨性就愈好。
  8. In light of great harm from alkali - aggregate to concrete, the alkali activation of the limestone to be used as the aggregate for the concrete in the construction of zhangfeng reservoir is fully tested with petrographic method, accelerated mortar bar method and autoclave expansion test etc., so as to ensure the durability of the anti - abrasion concrete therein

    摘要堿骨料對混凝土的危害很大，為保證抗沖磨混凝土的耐久性採用巖相法、砂漿棒快速法、壓蒸法等4種方法對陽城下川灰巖進行檢驗，以充分揭示張峰水庫混凝土粗骨料是否存在堿活性。
  9. Secondly, choose the sample component, as different particle match of tungsten carbide and specifically heat treatment craftworks of solution and aging manufacture test piece, watch metallurgical structure of the test piece and do the tests of hardness and tension, at last do the abrasive wear test on the dynamic load abrasive wear test machine, analyze test datum, from the test data, conclusions are arrived that the hardnees of composite - alloy can be improved and wear - resistance be better by adding cr and other elements according to a given ratio

    本文對rp中速磨煤機耐磨件進行了運行與磨損情況分析，研究、提出了制備磨輥和盤瓦復合合金成分配比；並對製作的試件進行了固溶、時效等特定的熱處理工藝，觀察試件金相組織，進行機械強度試驗，最後做磨料磨損試驗，對磨損失效機理進行了深入的研究分析，對其耐磨性能與低合金鋼、高鉻鑄鐵進行了對比。
  10. The article developed the self - compensation repairing lubrication additives which endowed with new function to old lubrication oils according to the theory of self - compensation repairing theory by aided financially from china nature science fund ( ratification number : 59975039 ). the first, the article studied the tribological effect of several kinds of lubrication additives by single - phase, two - phase and three - phase mixture by four - ball machine. the article studied the effect of the mixture ratio and the additive concentration on tribological effect - antifriction, wear - resisting and bearing capacity

    論文首先以四球法，對新合成的幾種潤滑添加劑的單相和雙相、三相復配后的摩擦學特性進行了較系統地研究，研究了復配比例和添加量等對其摩擦學性能?減摩、耐磨、承載性能的影響，在此基礎上優選了es12和esm122兩種潤滑添加劑，對其進行了較系統的磨損自補償修復效應及其摩擦學效應研究和對四種成品潤滑油的適應性研究，並對摩擦表面的自補償膜進行了紅外光譜分析。
  11. With the hardness tests, it is indicated the hardness of the nano alumina or nano silicon carbide coating is improved to 1. 6 - 2. 5 times as that of the plasma spraying coating. with the wearing tests, it is indicated that low laser power employed, the wearing performance of the coating without nano material increase to 1. 3 times as that of the plasma coating, at the same time, the wearing performance of the coating with nano material increase 2. 3 - 6 times as that of the plasma spraying coating, the wearing mechanism is further analyzed. with the erosion tests, it is indicated that the erosion performance of the coating with nano material increase five times as that of the plasma spra

    與相應等離子噴塗層相比，硬度測試表明，含納米al _ 2o _ 3或sic的各種復合塗層硬度提高了0 . 6 - 1 . 5倍左右；耐磨性測試表明，小功率下單純的激光重熔耐磨性提高了30 ，而納米滲入后塗層的耐磨性提高了1 . 3 - 5倍左右，對耐磨性提高的機理作了進一步的探索和分析研究；耐蝕性測試表明，經激光熔覆納米滲入后的各種塗層耐蝕性能提高了4倍以上，同時塗層厚度、表面質量對腐蝕性能有影響。
  12. It is believed that the formation of a1n is not only helpful for improving the properties of samples, but also helpful for bonding. bn and al. sem photos show the river pattern which is bond with tough fracture, bn particles and cnts are also observed. hardness measurement, frictional wear test results reveal that the contents of bn and cnts have apparent influence on the properties of specimens

    單獨添加bn和cnts時，樣品的硬度和耐磨、減摩性能都有不同程度的提高；同時添加bn和cnts浙江大學碩士學位論文時，兩者之間表現出明顯的相互作用:樣品的性能可能高於bn和cnts影響的簡單加合，也可能低於對比樣品（無bn和cnts ）的性能。
分享友人
分享到 Line

分享到臉書