相極觸點 的英文怎麼說

中文拼音 [xiāngjíchùdiǎn]
相極觸點 英文
phase pole contact
  • 相 : 相Ⅰ名詞1 （相貌; 外貌） looks; appearance 2 （坐、立等的姿態） bearing; posture 3 [物理學] （相位...
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  1. Having said all these problems of the film, i don t mean this film is totally worthless. lee jung - jae displays his glamors as usual. he constructs the shy and timid image of u - in convincingly, though i still think this character is quite freaky you ll agree with me if you have seen his behavior in the film

    男主角李政宰和觸片一樣內向，但不及該片角色的可愛，相反有點變態，如躲在女廁偷聽別人小便看咸網和合成相自瀆等，是內向得有點可怕的人物，如果極端發展下去很可能會成為偷窺狂和色魔。
  2. Circuit design is the basis of design of demultiplexer. speed, power and chip area are the main factors that should be considered in circuit design. every circuit structure has its merits and drawbacks, e. g. cmos logic family has a slower speed, but lower power, smaller area, scfl ( source couple fet logic ) family has a higher speed, but higher power, larger area. we should choose a proper circuit structure or their mixed structure for certain design to get a good tradeoff among the three factors. flip - flop is the fundamental element of demultiplexer, setup time and hold up time are key factors, which influence the speed of circuit, thus the design aim is how to reduce them. in this thesis we place emphasis on the design of scfl latches

    速度、功耗、面積是電路設計要考慮的主要因素，不同的電路形式具有不同的優缺點，如cmos互補邏輯電路功耗低，面積小，速度相對較慢； scfl （源極耦合fet邏輯）電路速度高，功耗和面積較大。所以要針對具體設計需要選用適當的電路形式或其組合結構，以滿足設計要求。觸發器是分接器的基本組成單元，建立時間和保持時間是影響電路速度的關鍵，所以減小建立時間和保持時間是觸發器設計的主要目標，本文著重介紹了scfl鎖存器的設計和優化方法。
  3. In this new protocol : 1 ) channel reservation decision and the event of hearing rts / cts are separated ; 2 ) channel reservation rules are newly redesigned ; 3 ) two items are added into rts / cts frame for nodes to make a channel reservation decision ; 4 ) a new signaling frame, beam pattern change ( bpc ) frame, is adopted in order to release the protocol aggressiveness

    該協議所做出的改進有: 1 ）通道預留判決不再與是否收到rts / cts幀直接相關; 2 ）通道預留判決的觸發時機以及具體規則被重新設計; 3 ）在rts / cts幀加入了兩項新的內容方便節點做通道預留判決; 4 ）增加了一條新的信令幀bpc （ beampatternchange ）幀，用於進一步釋放協議積極性。
  4. Based on the experimental study and inelastic theory, the ultimate flexural capacity of steel encased concrete composite beams are derived. the difference between steel encased concrete composite beams with full shear connection and beams with partial shear connection, together with the relationship between the inelastic neutral axis of steel parts and concrete parts, are considered in the formulae. the calculation results of the eight specimens with full shear connection and the three specimens with partial shear connection are in good agreement with the experimental data, which validates the effectiveness and efficiency of the proposed calculation methods. furthermore, the nonlinear finite element analysis of the ultimate flexural capacity of the steel encased concrete composite beams is performed. nonlinear material properties and nonlinear contact properties are considered in the finite element analysis. the finite element analytical results also correlate well with the experimental data

    基於外包鋼混凝土組合梁的試驗研究和塑性理論，按照鋼梁和混凝土塑性中和軸相對位置的不同，分別推導了完全剪切連接和部分剪切連接的外包鋼混凝土組合梁的正截面極限抗彎承載力的計算公式，並對外包鋼混凝土組合梁進行了非線性有限元分析，分析中重點考慮了材料非線性和接觸非線性. 8根完全剪切連接和3根部分剪切連接試件的正截面極限抗彎承載力的計算結果及有限元分析結果與試驗結果吻合良好
分享友人
分享到 Line

分享到臉書