真空燒制 的英文怎麼說

中文拼音 [zhēnkōngshāozhì]
真空燒制 英文
vacuum firing
  • 真 : Ⅰ形容詞（真實） true; genuine; real Ⅱ副詞1 （的確; 實在） really; truly; indeed 2 （清楚確實） cl...
  • 空 : 空Ⅰ形容詞（不包含什麼; 裏面沒有東西或沒有內容; 不切實際的） empty; hollow; void Ⅱ名詞1 （天空） s...
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 真空 : [物理學] vacuum; empty space; vacuo
  1. Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )

    本研究以武裝直升飛機防護裝甲材料為研究對象，採用真空熱壓粉末冶金燒結工藝制備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料，結合其力學性能、掃描電鏡和界面微區能譜分析結果，分析了sic _ p al復合材料的真空燒結過程中的界面現象，以及材料增強和斷裂機理，並利用hopkinson高速壓桿沖擊實驗系統對其從靜態到動態（應變率為3 . 3 10 ~ （ - 3 ） s ~ （ - 1 ） 5 . 2 10 ~ 3s ~ （ - 1 ） ）的壓縮破壞響應進行了研究，分析了不同體積分數sic _ p al復合材料高應變率壓縮載荷下，材料的變形和微觀損傷機理，以及利用高速沖擊空氣炮測定了改復合材料制備剃度復合板的穿透性能。
  2. At present, our country is the largest producer and consumer in the horniness - alloy scopes. but now, this stove depends on import, hip - sinter stove ’ s self - develop and corresponding control system has important apply value

    目前我國是世界上最大的硬質合金生產與消費國，但生產所需的燒結爐仍主要依賴進口，自主研製低壓真空燒結爐及配套的控制系統無疑具有重要的應用價值。
  3. The sbf cultivation results by different surface modification methods were : nano - tio2 coating > alkali solution treatment > tio2 coatings sintered in normal pressure > tio2 coatings sintered in vacuum

    不同表面改性方法的sbf培養結果比較為：納米二氧化鈦塗層堿液處理方法常壓下燒結二氧化鈦塗層真空下燒結制備的塗層。
  4. The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads

    本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性，並在此基礎上以不同尺寸（ 42 362 m ）的鑄造碳化鎢顆粒為增強體，採用真空熱壓液相燒結技術制備了不同顆粒含量（ 0 45vol . ）的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料；以不同粒度的sic為磨料，在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。
  5. A pressing sequence can be started with or without a vacuum, and the firing chamber can be optionally flooded with protective gas

    在真空或沒有真空的條件下也可以啟動壓制過程，作為選項，焙燒室還可以使用保護氣體吹掃。
  6. So the titanium dioxide coatings were fabricated by cladding substrates to sinter in different work mediums, which included normal pressure and vacuum conditions. the surface morphology and phase constitution of coatings were analyzed

    本研究採用包埋燒結法分別在常壓和真空條件下在鈦合金試樣上制備二氧化鈦功能塗層，並對塗層的表面形貌和相組成進行了分析。
  7. Then, at the base of analysis of the technics process, designed the autocontrol technics flow chart of hip - sinter stove

    然後，在工藝過程分析基礎上設計了低壓真空燒結爐自動控制工藝流程。
  8. This first microprocessor - controlled dental oven with an integrated vacuum pump was only on the market for a short time : the fast evolution in the field of electronics led to its replacement

    它是第一代使用微處理機控制的牙科焙燒爐，並帶有集成真空泵，但推向市場的時間很短：電子設備的迅速發展使它很快退役。
  9. The influence of microstructure on the flashover performance of alumina ceramics has been studied systematically through investigating the flashover performance of different alumina ceramic samples. experimental results reveal that the flashover performance is affected by the grain sizes and its dispersiveness. the smaller grain size is, the higher flashover performance ; the less dispersiveness of grain sizes is, the higher flashover performance

    3 .通過研究用不同工藝制備的氧化鋁陶瓷絕緣子（同一材料配方不同燒成工藝、同樣氧化鋁含量不同添加劑）在沖擊電壓作用下在真空中的沿面閃絡特性和表面帶電特性，首次深入系統地探索了材料微觀結構對陶瓷材料沿面閃絡性能的影響規律。
  10. In this work, un - doped and nano sic doped mgb2 / fe tapes and wires were fabricated by the powder in tube ( pit ) technique, and the short samples were synthesized through two different routes of the traditional vacuum sintering and the sparking plasma sintering ( sps ). the sintering parameters were optimized in both sintering methods

    本文採用粉末套管法（ powderintube ）原位（ in - situ ）制備了非摻雜和納米sic摻雜的mgb2 / fe超導線帶材，分別採用常規真空燒結和放電等離子燒結（ sps ）兩種方式合成mgb2超導相，優化了燒結工藝參數。
  11. Application characteristics ： it ' s made bronze or iron powder, mold pressed under high pressure and then sintered under high temperature, and oil is soaked into the homogeneously spreaded tiny pores of the metal under vacuum

    應用特點：該產品是以銅粉或鐵粉為原料，經模具壓制、高溫燒制、真空浸油后加工而成。
  12. According to control system requirements of hip - sinter stove, the thesis selected plc of s7 - 300 series of siemens as main controller to autocontrol produce process, and the industry person computer which produced by advantech ltd. and hmi which produced by proface ltd. as the monitor computer, which composed plural computer control system

    根據低壓真空燒結爐控制系統需求分析，選用了西門子公司的s7 - 300系列plc作為主控制器對生產過程進行過程自動控制，以及研華工控機和proface公司觸摸屏作為監控計算機，構建了一個低壓真空燒結爐兩級計算機控制系統。
  13. Abstract : in this paper, the porous - metal nickel was prepared by filling pore - forming material and vacuum sintering process. the influence of pore - forming material on the properties of porous - metal nickel was discussed

    文摘:採用添加造孔劑、真空燒結工藝制備了多孔金屬鎳材料，並主要討論了造孔劑含量對材料性能的影響。
  14. At the base of participating in the system design and debug of the dy - 500 hip - sinter low - pressure and vacuum sinter stove which is investigated by the zigong horniness - alloy ltd. this paper conclude the practice and work, according to the sense and the embed analysis, this paper including : aim at hip - sinter stove, analyse technics principle of the dewaxing, the vacuum sintering and the hot isostatic pressing by low pressure

    在參與自貢硬質合金有限責任公司研製的dy - 500型低壓真空燒結爐自動控制系統設計和調試的基礎上，本論文對實踐工作進行了總結與提高。根據現場經驗和深入分析，論文的主要內容有:針對低壓真空燒結爐，分析脫蠟、真空燒結、低壓熱等靜壓工藝原理，並論述了溫度、真空度、壓力三個主要因素對生產過程的影響。
  15. According to the types select of sensor and transducer and the satistic mount of i / o of the control system of hip - sinter stove, the thesis configured and select the types of control system hardwares. then, designed the plc autocontrol program of hip - sinter stove by the step 7 v5. 2 software and the monitor program of montor computer by the wincc v6 monitor conifigure software. consequently, it improved the whole performance of the stove a lot

    根據低壓真空燒結爐控制系統i / o的統計和傳感器的選型，對控制系統硬體進行了配置和選型，並採用step7v5 . 2軟體編制了低壓真空燒結爐plc自動控製程序以及利用winccv6監控組態軟體完成了監控計算機上的監控軟體開發，大大改善爐子的整體性能。
  16. Damping properties of aluminum foams produced by pressing - dissolution - vacuum sintering process

    真空燒結法制備泡沫鋁的阻尼性能研究
  17. Limn2o4 films made under these conditions showed good performances, so synthesizing limn2o4 film at low sintering temperatures was realized

    最後對真空燒結進行初步探討，在較低的燒結溫度下制備出了電性能較好的limn204薄膜，實現了低溫合成limn2o4薄膜電極。
  18. In this paper, firstly, monolithic materials cosb3 and bi2te3 were prepared by sparkle plasma sintering ( sps ) respectively, and at the same time the microstructure of cosb3 and bi2te3 were studied by sem ; the seebeck coefficients and electrical conductivities of monolithic materials were measured by standard - four - probe method ( ulvac zem - 700 ) in a he atmosphere simultaneously, and their thermal conductivities were investigated by laser flash method ( tc - 7000 ) in vacuum. secondly, the junction temperature of graded bi2te3 / cosb3 thermoelectric materials was optimized based on the thermoelectric transport properties of monolithic materials, also when graded materials were used in the temperature difference ranging from 300k to 800k, the length ratio of monolithic materials cosb3 and bi2te3 were optimized in theory. thirdly, graded bi2te3 / cosb3 thermoelectric materials were prepared by two - step sps sintering, and the relationship between its average seebeck coefficients and temperature were calculated by theory mo del

    均質材料cosb _ 3和bi _ 2te _ 3的電導率和seebeck系數採用標準四端子法于he氣氛下在zem - 1上同時進行測量；熱導率採用激光微擾法（ tc - 7000 ）于真空狀態下進行測量；其次，在對均質材料cosb _ 3和bi _ 2te _ 3熱電傳輸特性研究的基礎上，對結構梯度bi _ 2te _ 3 cosb _ 3熱電材料的界面溫度進行了優化；為了使結構梯度bi _ 2te _ 3 cosb _ 3熱電材料在300k至800k的溫度范圍內具有最佳的熱電性能，本研究同時對梯度結構熱電材料當中均質材料cosb _ 3和bi _ 2te _ 3材料的長度進行了優化設計；第三，通過兩步放電等離子燒結的方法制備出了結構梯度bi _ 2te _ 3 cosb _ 3熱電材料；採用理論計算的方法研究了梯度結構熱電材料平均seebeck系數和溫度的關系；同時為了驗證設計的結果，本論文對結構梯度bi _ 2te _ 3 cosb _ 3熱電材料的開路輸出電壓和熱端溫度之間的關系及梯度材料在300k至800k的溫度范圍內使用時的功率輸出進行了相應的研究。
  19. The experimental techniques ( such as sedimentation equipment, controlling the size and size distribution of powders, the concentration of suspension ) have been devised subtly. on the basis of theoretical and densification design, the w - mo - ti fgm has been obtained by particle settling and hot pressing sintering. the structures of specimen were observed by electron probe

    通過對實驗工藝，如沉降設備、原料粒度及粒度分佈的控制、懸浮液濃度等方面進行精細的設計，在理論設計和緻密化研究的基礎上，通過顆粒共沉降得到梯度沉積體，並通過真空熱壓燒結得到w - mo - ti功能梯度材料。
  20. In this paper, ti3sic2 material and ti3sic2 / sic composites, which were fabricated by non - pressing sintered and hot - pressing sintered methods are mentioned and the effects of the synthesis conditions on the phase composition, microstructure and mechanical properties were investigated

    本文通過無壓真空燒結和熱壓燒結制備了ti _ 3sic _ 2材料和ti _ 3sic _ 2 sic復合材料，研究了工藝制度對復合材料物相組成、顯微結構和力學性能的影響。
分享友人
分享到 Line

分享到臉書