瞬態誤差 的英文怎麼說

中文拼音 [shùntàiwùchā]
瞬態誤差 英文
transient error
  • 瞬 : Ⅰ名詞（眼珠一動; 一眨眼） wink; twinkling Ⅱ動詞（眨眼） wink
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 瞬態 : transient; instantaneous condition; transient state
  • 誤差 : error
  1. This thesis aims to design one instrument to measurement of the fluid thermal conductivity by used the hot - wire method ( hwm ). firstly expatiated on the theory of this method, got the academic solution by analyzing the ideal model, and then amended the ideal solution to satisfy the factual situations

    本文重點討論瞬態熱線法測量液體的導熱系數，從理論與實驗及數值模擬的角度分析探討瞬態熱線法測量液體導熱系數原理及其實現過程，並分析理論與實際測量過程中的誤差產生原因及誤差避免與校正。
  2. Abstract : the hot wire anemometer and the ensemble average method are used to measure and study the dispersion turbulent transient feature in a closed cylindrical explosion bomb. the comparison of the dispersion turbulent parameters from different shapes of closed explosion bombs is presented. the relation between errors and numbers in dispersion turbulent measurement with the ensemble average metod is discussed

    文摘:採用熱線風速儀和系綜平均法測定和研究了封閉圓柱形粉塵爆炸罐內揚塵湍流的瞬態特性，並與球形爆炸容器內已測定的揚塵湍流瞬態特性進行了比較，對系綜平均法用於揚塵湍流的測量誤差與測量次數的關系進行了探討。
  3. However, the accuracy and instantaneity of the most used mark post measurement method are not good and the errors of five - wheel measure device with contacting measurement principle are serious when it is used in soft and undulated surface field

    但是，常用的標桿法測量精度和瞬態性較差，接觸式測量的五輪儀法用於田間松軟、不平的地況誤差較大。
  4. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  5. The transient mathematical equations are addressed for the coupled heat and moisture transfer by taking account of moisture accumulation procedure. an analytical method by means of the transfer function is proposed to predict the transient distributions of temperature and moisture content at different interfaces in walls. a numerical analysis approach based on an efficient finite - difference method is developed to deal with the procedure of coupled heat and moisture transfer in a multilayer wall with nonlinear boundary conditions considered

    建立了考慮濕積累過程的瞬態熱濕耦合模型，在方程中引入了濕積累項；發展了一種傳遞函數解析方法進行墻體內不同剖面處溫度和含濕量的動態預測；首次提出了一種基於有效有限差分法預測非線性邊界條件下多層多孔結構內的傳熱傳濕過程的數值分析方法，求解過程中考慮了瞬態邊界條件，從而避免了通常處理中由於邊界條件設定為常數而給計算帶來的誤差，對于多層結構每一層物性參數的非連續性，則採用了有效的有限差分逼近處理。
  6. That test part of the software is primarily used to complete the test of some parameters, such as time base, time - expand, time interval, voltage interval, vertical, stable state, transient state and scanning linearity. the result of the test needs to be analyzed and judged. clear user interface and timely warnings for mistakes of testing process inside because of the user ' s fault operating make whole test process more easier than it did on a time

    該軟體的測試部分主要用於完成對示波器掃描時間系數、擴展掃描時間系數、 t時間測量、 v電壓測量、垂直偏轉系數、頻帶寬度、校準信號、脈沖瞬態響應、掃描線性誤差時等參數的測試檢定任務，並對測試結果進行及時的分析和判斷，由於界面清晰，而且對測試過程中由於用戶的誤操作都有及時的錯誤提示，使得整個測試過程簡單易行，對于用戶來講掌握起來也更為方便些。
  7. One - cycle control method is a nonlinear control method. by controlling the switch duty - ratio, it can make the average value of a switched variable equal to or proportional to the control reference in each cycle, so the stationary and transient errors are eliminated

    單周控製法是一種非線性控製法，它通過控制開關占空比，使在每個周期內開關變量的平均值與控制參考信號相等或成一定比例，從而消除穩態和瞬態誤差。
  8. One - cycle control technique is conceived to control the duty - ratio d of the switch in real time such that in each cycle the average value of the chopped waveform at the output diode of the switch rectifier is exactly equal or proportioned to the control reference. it can eliminate automatically instantaneous error in every one cycle and the error belonging to the former cycle ca n ' t be brought to next cycle

    單周期控制技術的基本思想是控制開關的占空比，在每個周期內強迫開關變量的平均值與控制參量相等或成比例，它能在一個開關周期內自動消除瞬態誤差，前一周期的誤差不會帶到下一周期。
  9. The same conclusion as derived from the original pda under approximate condition is concluded this way without any approximations. the second method is the instant - state performance prediction based on the hyca method. this method not only gives the off - line recursive error variance relation, but also gets a series of performance measurement such as track life

    然後應用兩種方法對其進行性能估計和預測，一是基於riccati方程的穩態性能估計，其結果與pda演算法近似條件下得出的結論相同；二是基於hyca方法的瞬態性能預測，不僅給出了誤差方差的離線遞推關系，而且得到了航跡壽命等一系列性能指標的估計值。
  10. On the basis of the principle of direct torque control, a control strategy of the grade of errors for induction motor has been proposed to improve the performance of powertrain system of hybrid vehicle in this thesis. the stator flux error, electric magnetic torque error and flux position angle are considered as control variables, and the switching states are determined by the control rules of the direct torque control

    本文在直接轉矩控制系統的基礎上提出了一種基於誤差等級的直接轉矩控制dtc策略，它以電機定子磁鏈誤差、電機電磁轉矩誤差及磁鏈位置角作為控制變量，然後根據直接轉矩控制原理制定控制規則來選擇開關狀態，進而提高系統瞬態時的轉矩響應。
  11. The paper proves that in the 2d non - linear case, the coulomb gauge is been meet naturally. in the paper, the second - order isoparametric fem is adopted in the non - linear transient magnetic field simulating excited by current source and the results of transient field and static field solved by the second - order isoparametric and linear fem are compared and analyzed, besides, the effect of the eddy currents in the magnetic materials of the different conductivity is analyzed, it is obtained that the magnetic material of high magnetic conductivity and low loss should be chosen in designing of pma

    文中採用二次等參元有限元法推導出在電流源激磁下的非線性瞬態磁場的計算方法和編制了相應的計算程序，並採用二次等參元有限元法和雙線性有限元法分別對瞬態場和靜態場進行了計算，並對計算結果進行了誤差分析，此外，還對不同電導率的導磁材料中渦流產生的影響進行了分析，得到結論設計永磁操動機構時，應選擇導磁性能好，損耗低的導磁材料。
分享友人
分享到 Line

分享到臉書