砂處理 的英文怎麼說
中文拼音 [shāchǔlǐ]
砂處理
英文
sand conditioning-
Application of partial exchangeability measurement on quality control of bevel gears
多變量統計在砂處理過程中的應用This dust catcher fits for purifying air in the foundry workshop, especially place with high content of powder, high temperature and high demand on purification, such as sand shakeout clean and sand treatment
該除塵器運用於鑄造車間氣體的凈化,尤其是粉塵含量高氣體溫度高及凈化要求高的場合,如落砂清理砂處理工布等。Especially developed touch - up primer on blasted areas both below and above waterline
特別開發的底漆,通用於水線上下的噴砂處理部位。The surface finish for the castings we can provide with are sa the following ; backing. zinc plating. chrome plating and nickel plating for the carbon steel and the low alloy steel castings ; tumbling. hand dull polishing. mirror polishing, electrolytic polishing and passivation treatment for the stainless steel castings and sandblasting. including glass bead blasting. corundum - sand blasting and quartz - sand blasting for all the steel castings
我公司有能力對鑄件表面作如下精整處理,對于碳鋼和低合金鋼,可以作發黑、鍍鋅,鍍鉻,鍍鎳處理,對于不銹鋼,可作研磨,手工拉絲拋光及鏡面拋光,電拋光,純化處理,所有鋼種可作噴砂(玻璃砂,鋼玉砂,石英砂)處理。The surface finish for the castings we can provide with are as the following : blacking, zine plating, chrome plating and nichel plating for the carbon steel and the low alloy steel castings ; tumbling, hand dull polishing, mirror polishing, electrolytic polishing and passivation treatment for the stainless steel castings and sandblasting, including glass bead blasting, corundum - sand blasting and quartz - sand blasting form all the steel castings
我公司有能力對鑄件表面作以下精整處理,對于碳鋼和低合金鋼,可以作發黑、鍍鋅、鍍鉻、鍍鎳處理;對于不銹鋼,可作研磨、手工拉絲拋光及鏡面拋光、電拋光、鈍化處理;所有鋼種可作噴砂(玻璃砂、鋼玉砂、石英砂)處理。According to different backing materials, we can choose the suitable grain size to sanding - blast treating and shape hard chromium plating that isn ' t shaping after being plated, which is the key to solve hard chromium plating like pear ' s skin
根據不同的基材選擇合適的砂型進行噴砂處理和鍍后沒有修飾的一次電鍍硬鉻成型工藝是解決電鍍梨底硬鉻的關鍵所在。Sand treatment craftwork equipment
砂處理工藝設備Dust catching hole is set on the top which can be directly connected with ventilation system for sand treatment to lower dust of used sand and enhance quality of moulding sand
在頂部設置吸塵口,可以在砂處理通風系統中直接聯網,降低舊砂粉塵量,提高型砂質量。The influence of some problems with dust system design for sand treating section on dust cleaning effect was described : 1
摘要介紹了砂處理工部除塵系統設計中幾個問題對除塵效果的影響。According to some workpieces ' usage demands of the rough degree on the surface of hand chromium plating, through a serial of experiments, we have satisfied the requirements of the using workpieces ' hard chromium layer ' s consistence and rough degree through adding sand - blast treating to the workpieces ' which are not dealt after polishing and adopting some effective control ways to the plating frock and craft, thereby carrying out plating hard chromium like pear ' s skin
摘要根據某些工件對電鍍硬鉻層表面粗糙度的使用要求,經過一系列的試驗,通過機件毛坯拋光后增加噴砂處理及時電鍍工裝、工藝採用一些有效的控制手段進行電鍍梨底硬鉻,滿足了工件使用中對硬鉻層硬度和粗糙度的要求。Machine body fully sand blasted
全機表面玻璃砂噴砂處理。To be used as a pre - fabrication primer on blast - cleaned steel surfacees in automatic shop - priming plants to protect steel during transport, storage and production
作為預處理底漆用於噴砂處理鋼材,保護鋼材在運輸,儲存和生產中不受損害。適用於車間自動流水線施工。This machine fits for dispersing moulding sand on wet type moulding mechanical sand treatment production line or crushing used sand after falling. this machine can equalize moisture of used sand after water spraying, cooling effect can be increased if it is matched with used sand cooling equipment
該機用於濕型造型機械化砂處理流水線上對型砂進行鬆散,或對落砂后的舊砂進行破碎該機可使噴水后的舊砂水分均勻化,與舊砂冷卻設備配套使用時可增加冷卻效果。Dressing of the molding sand
模砂處理Preparation of steel substrates before application of paints and related products. surface roughness characteristics of blast - cleaned steel substrates. part 2 : method for the grading of surface profile of abrasive blast - cleaned steel. comparator procedure
塗料和有關產品使用前鋼基片的制備.噴丸處理鋼基片的表面粗糙度特性.第2部分:噴砂處理表剖面的定級方法.比較程序Condensation resin sand treatment equipment
冷凝樹脂砂處理設備Automatic sand plant
自動鑄砂處理設備Abstract : based on plenty practical experiences many years , both application and problems in all kinds of green sand preparation equipment and auxiliary devices have been expounded personal point and suggestion have been put fouth against problems occurring in technology
文摘:筆者根據多年積累的豐富實踐經驗,分別闡述了各種濕型砂處理設備及輔助裝置的使用情況及存在的問題;並對砂處理工藝中出現的諸多問題提出了自己的看法和改進建議。Roughness comparison specimens - specification for spark - eroded, shot - blasted, grit - blasted, and polished specimens
表面粗糙度比對試樣.第2部分:電火花加工噴丸處理噴砂處理及拋光試樣規范20 200m3 h mechanical clay sand treatment line turn - key project
20 200m3 h機械化粘土砂處理線交鑰匙工程分享友人