硬性離合器 的英文怎麼說

中文拼音 [yìngxìnglígěqì]
硬性離合器 英文
positive clutch
  • 硬 : 形容詞1 （堅硬） hard; stiff; tough 2 （剛強; 堅定; 強硬） strong; firm; tough; obstinate 3 （勉...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 離 : Ⅰ動詞1 （離開） leave; part from; be away from; separate 2 （背離） go against 3 （缺少） dispens...
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 硬性 : hardness; rigid; stiff; inflexible
  • 離合器 : clutch; throw out; ratcheting; clutch coupling離合器操縱桿 clutch operating lever;離合器齒輪 clut...
  1. Performance for a piezoresistive transducer pressure sensor to thermal and pressure environments can be predicted by finite element method. a simplified 1 / 8 model, considering silicon dioxide and nitride process as well as stack anodic bonding and adhesive bonding processes, was developed. the fem results were found to be comparable to experimental data. case studies suggested that pyrex stack induces certain amount of non - linearity, while it isolates hard epoxy nonlinear effect. flexible epoxy bonding or soft adhesive bonding is preferred to the packaging process. the viscoelasticity and viscoplasticity of bonding material will result in hysteresis and drift errors to sensor output. however, soft adhesive s influence on sensor can be ignored under relative stable environments. more over, detailed design and process information will help to improve modeling application

    熱、壓環境下壓阻變換壓力傳感器的性能可以通過有限元方法預測.這里研究了簡化的1 / 8模型，模型考慮了二氧化硅和氮化硅生成過程及堆陽極鍵合和膠粘結合過程.結果發現有限元預測結果和實驗數據具有可比性.範例研究表明，硼硅堆導致產生一定的非線性，但它隔離了硬環氧樹脂的非線性.在包裝過程中最好使用柔性環氧黏合或軟黏膠性結合.黏合材料的黏彈性和黏塑性將會導致傳感器輸出的滯后和漂移誤差.然而，在相對穩定的環境下，軟黏合劑對傳感器的影響可以忽略.此外，詳細的設計和過程信息有助於提高模型的適用性
  2. In hardware design, the intactness of the camera ’ s original structure has been maintained to the very extent, the facility of assembling and disassembling devices have been achieved. the remote control has been realized by the separation of active devices from passive devices. in software design, vc + +, keil c51 and matlab are employed, bringing an easy way to communicate with the system

    在硬體設計方面，最大限度地保證了相機原始結構的完整性，並且保證了器件易安裝易拆卸，有源無源器件的分離更實現了遠距離控制;軟體設計方面，選用了vc + + 、 keilc51和matlab ，通過精心的設計合理地實現了人機對話。
  3. The work of this paper originates from the momentous project of science and technology in fujian province, “ study on supporting technology of tele - medicine information sharing platform based on pacs and broadband network ”. firstly, the system of networking is the foundation of platform construction, so the author design the hardware structure of interface server based on the physical isolation technique and the network system of platform based on the technique of vpn ( virtual private network )

    本論文結合福建省重大科技項目? ? 「基於pacs和寬帶網的遠程醫療信息共享平臺及其支撐技術的研究」的設計，完成了以下幾個方面的工作:首先，網路系統是平臺建設的基礎，作者以網路物理隔離技術為核心對介面服務器系統的硬體架構以及平臺網路建設進行深入分析，並結合實際設計了基於vpn技術的高安全性能的平臺網路系統實現方案。
  4. Microprocessor ' s i / 0 is the seria1 interface chip, making the system simplified and reliability increased. the state and seat of throttle. clutch and brake, the rotates speed of engine, the direction of motive force etc are the paraneters

    自動控制系統硬體電路以at89c52為核心，沒有外擴ram 、 rom ， i / o介面晶元採用串列工作方式，接線簡單，可靠性高；設置油門、離合器、剎車狀態和位置，發動機轉速，動力流向等傳感器獲取運行參數。
分享友人
分享到 Line

分享到臉書