碳化鎢合金 的英文怎麼說

中文拼音 [tànhuàwūgějīn]
碳化鎢合金 英文
carbon tungsten alloy
  • 碳 : 名詞[化學] （非金屬元素） carbon （c）
  • 鎢 : 名詞[化學] （金屬元素） tungsten; wolfram（w）
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 金 : Ⅰ名詞1 （金屬） metals 2 （錢） money 3 （古時金屬制的打擊樂器） ancient metal percussion instrum...
  1. Composite welding of the diamond and tungsten carbide

    金剛石與碳化鎢的復合堆焊
  2. Technical conditions of steel - bonded tungsten carbide

    碳化鎢鋼結硬質合金技術條件
  3. In the investigations on laser cladding, experiments and analyses of laser clad nickel - based alloys and nickel - based ceramal composite alloys on steel substrates were performed to improve wear - resistance and corrosion - resistance properties of the coatings

    以提高材料表面的耐磨、耐蝕等性能為目的，採用預置和送粉熔覆工藝方式，對常用的鎳基合金和鎳基碳化鎢金屬陶瓷合金塗層進行系統研究。
  4. It is reported that hard alloy scrap is treated by electroosmosis and electrolysis together taking sulfuric acid as electrolyte in order to recover cobalt metal and tungsten carbide

    報道了以硫酸為電解質，同時用電溶法和電滲析法處理廢硬質合金、回收金屬鈷和碳化鎢的原理和方法。
  5. The particles distributed hi the matrix of grey cast iron, but some contact each other. the composite layer extend gradually into the substrate. when volume fraction of wc is 36 wt % and 27 wt %, the matrix of the composite is high chromium cast iron, consist of white carbide bars and the austenite. wc particles distributed uniformly, retaining approximately quondam granular form in the composite layer which has an evident interface area with the substrate, with good bonding strength

    對不同碳化鎢體積分數的灰鐵和低鉻鑄鐵基復合材料的微觀組織結構分析表明：碳化鎢體積分數為52時，復合層內基體為灰口鑄鐵組織，顆粒直接分佈在灰鐵基體上，部分碳化鎢顆粒有相互接觸的現象，基材與復合層之間沒有明顯的過渡；碳化鎢體積分數為36 、 27時，復合層內基體為高鉻鑄鐵，由面塊狀的奧氏體和白條狀碳化物組成，碳化鎢顆粒表面固溶於基體組織中，粒形基本保持完整，分佈均勻，與基體構成冶金結合，基材與復合層之間存在一個明顯的平緩過渡區。
  6. The strength and wear resistance of diamond drill bits for petroleum exploitation will be increased considerably when cast tungsten carbide is applied and adheres to the substrate firmly with cast tungsten carbide of 80 - 200mesh as the skelton and copper alloy as the soldering material in a process of non - pressure immersion

    石油鉆探行業用的金剛石鉆頭，用粒度為80 ? 200目的鑄造碳化鎢粉作骨架，採用無壓浸漬工藝，以銅合金作釬焊料，將鑄造碳化鎢與基體牢固結合，強度、耐磨性大大提高。
  7. In 1958, ganzhou concentration plant was established and started its production. after 1963, tungstic acid, apt, w powder, wc powder and cemented carbide could be produced too

    1958年，贛州精選廠建成投產。 1963年以後，進一步發展到生產鎢酸、鎢酸鈉、仲鎢酸銨、鎢粉、碳化鎢粉、硬質合金等。
  8. The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads

    本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性，並在此基礎上以不同尺寸（ 42 362 m ）的鑄造碳化鎢顆粒為增強體，採用真空熱壓液相燒結技術制備了不同顆粒含量（ 0 45vol . ）的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料；以不同粒度的sic為磨料，在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。
  9. Main product : tungsten carbide powder, roll ring, anvil and cylinder, mining button bit, dies nib for various application : cold heading dies, drawing dies and non - magnetic carbide dies. all of the products mentioned above could be offered in blank or finishing product

    公司主要產品有：碳化鎢粉硬質合金輥環頂錘和壓缸冷鐓模無磁合金礦山柱拉絲拉管模棒材板材非標模具及硬質合金精密加工產品等，廣泛應用於鋼鐵標準件金剛石粉末冶金石油礦山磁性材料機械加工電子等行業。
  10. The results show that the composites were more wear resistant than the matrix, contributing to the " volume effect " and " size effect ", the wear resistance increases with the particle content and size. the composite shows better wear resistance than high chromium cast iron material especially in low load and fine abrasive test condition. the results also indicate that the composite strengthened by ageing treatment was more wear resistant than as - cast composite

    磨損試驗結果表明，鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料具有比較高的抗磨料磨損能力，而且其耐磨性隨著鑄造碳化鎢顆粒體積分數及尺寸的增大而提高，表現出了強烈的「體積效應」及「尺寸效應」 ，尤其是在低載荷、細磨料磨損條件下，復合材料表現出更好的而寸磨性，即使與高鉻鑄鐵（ cr28 ）相比也有很大程度的提高。
  11. Tungsten - carbide drawing die

    碳化鎢拉絲模硬質合金拉線模
  12. Tungsten carbide drill steel

    碳化鎢硬質合金鋼釬
  13. Technical conditions of steel - bonded tungsten carbides

    碳化鎢鋼結硬質合金技術條件
  14. Steel bonded tungsten carbides - determination of impact toughness

    碳化鎢鋼結硬質合金沖擊韌度的測定
  15. C a steel bonded tungsten carbides - determination of rockwell hardness scales c and a

    碳化鎢鋼結硬質合金洛氏硬度
  16. Steel bonded tungsten carbides - determination of transverse rupture strength

    碳化鎢鋼結硬質合金橫向斷裂強度的測定
  17. Reseach on microstructure of steel bonded tungsten carbide by electroslay melting and casting

    電冶熔鑄碳化鎢鋼結硬質合金的微觀組織研究
  18. Raw and auxiliary materials : iron powder, copper powder, tungsten powder, tungsten - carbide powder, stainless ( high - speed ) steel powder, magnetic material, ceramic material, nanophase material and other metal powders and alloy powders

    原輔材料類：鐵粉、銅粉、鎢粉、碳化鎢粉、不銹（高速）鋼粉、磁性材料、陶瓷材料和鈉米材料及其它元素金屬粉末及合金牌號的粉末等。
  19. Tungsten carbide - copper alloy

    碳化鎢銅合金
  20. An ultra fine cemented carbide with tungsten powder and binder cobalt

    一種由碳化鎢和粘結金屬鈷組成的超細顆粒硬質合金。
分享友人
分享到 Line

分享到臉書