磨損物 的英文怎麼說

中文拼音 [mósǔnwù]
磨損物 英文
wearer
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 損 : Ⅰ動詞1 （減少） decrease; lose 2 （損害） harm; damage 3 [方言] （用尖刻的話挖苦人） speak sarcas...
  • 物 : 名詞1 （東西） thing; matter; object 2 （指自己以外的人或與己相對的環境） other people; the outsi...
  • 磨損 : wear and tear; abrasive wear; abrase; abrade; detrition; wear; scuff; wear out; fray; battering; ...
  1. The pulse pneumatic conveying system has been a important transporting method for grain material, because of lower velocity, higher ratio of blend and a littler gas, as well as shattering less materiel, abrasing pipeline and easy recovery

    脈沖氣力輸送裝置以其低速、高混合比、低耗氣量等一系列持點，並由此帶來的被輸送物料破碎少、管道磨損小、產生粉塵少並且易於回收等優點，成為新一代粉粒料氣力輸送設備，並且被廣泛使用。
  2. Frosting occurs when two fibers differing in both color and abrasion resistance are combined in a fabric.

    兩種顏色和耐磨損性能不同的纖維組合的織物也會出現霜花色。
  3. Resistant to wear, impact, salt water and aliphatic hydrocarbons

    可耐磨損、碰撞，耐海水和脂肪烴類物質。
  4. Frictional behavior is modified by colloidal silica or starch deposition.

    耐磨損性能可以通過在織物上沉澱膠狀硅或澱粉一類物質而得到改善。
  5. The shortage of this kind of system is that the mechanical frictional waste and noises are n ' t neglectable. this results in the low efficiency and the short life of the equipment so that it ca n ' t guarantee the reliability of the system for long term running

    過去，物流傳輸系統由旋轉電機驅動，其缺點是機械磨損和噪音較大，這使得設備的效率不高，使用年限不長，無法保證系統長期運行的可靠性。
  6. Daily drivers are exposed to day - in, day - out wear and tear as well as exposure to inclement weather, road grime, air - borne pollutants, and other contaminants that land and settle on the paint surface etc

    白天開車的司機天天都有磨損，更何況是惡劣的天氣、公路的瀝青、空氣的污染物和其它污物都能導致漆面的損傷等等。
  7. Geotextiles and geotextile - related products - abrasion damage simulation sliding block test

    土工織物及相關製品.磨損模擬
  8. Geotextiles and geotextile - related products. abrasion damage simulation sliding block text

    土工織物及其相關產品.模擬磨損
  9. It is believed that the exposure of highly reactive surfaces during the wear process along with the high temperatures at asperity contacts act to " polymerize " the fluid, forming a viscous sludge, which inhibits bearing rotation

    研究表明，高溫下的金屬表面在磨損過程中會產生粘稠的「聚合物」物質，形成粘稠的油泥，阻礙了軸承旋轉。
  10. When fillings is other materials ( unprocessed montmorillonite, powder coal ash, co - composite of powder coal ash and organo - montmorillonite, co - composite ofcarbonizing calcium and organo - montmorillonite ) in the binder and content of organo - montmorillonite in the binder is five percent decided by tensile - shear experiment, tensile - shear strength of binder is up to tiptop ; at the same time, this paper carries out abrasion experiment, and, by comparison, concludes abrasion property of coating is optimum when content of organo - montmorillonite in the binder coating is five percent, and observes abrasion sample under set

    當膠粘劑中填料為其它物質（未處理蒙脫土、粉煤灰、粉煤灰和有機化蒙脫土共復合、碳化鈣和有機化蒙脫土共復合）時，通過拉伸剪切試驗確定膠粘劑中有機化蒙脫土含量為5時，膠粘劑的拉伸剪切強度最高；同時進行了沖蝕磨損試驗，通過比較得出，當膠粘劑塗層中有機化蒙脫土含量達到5時，塗層的耐沖蝕磨損性能最佳，並對沖蝕磨損試樣在掃描電子顯微鏡（ set ）上進行觀察。
  11. The highlights of this paper include : hoop toughness criterion for longitudinal heat checking of tool joint was introduced firstly ; failure criterion for crescent - shaped wear casing was established according to the results of full - scale collapse tests ; new - typed alloy for hardbanding of tool joint was developed, its property has showed good performance in the tests

    本文的主要創新點在於：以現場失效案例分析為基礎，提出了鉆桿接頭縱向熱裂的橫向韌性判據；通過對已磨損套管的實物擠毀試驗研究，確定了不均勻磨損套管的擠毀失效準則；設計出了具有獨立知識產權的鉆桿接頭硬化帶用新型耐磨減摩合金的成分，經實驗室試驗表明其性能可以達到或超過國外同類產品。
  12. The variation of friction coefficients of pa6 composites with loading also accords with the friction behaviors of elastic materials under lower load ( p < 100 n ) ; for cu counterface, the friction coefficients of pa6 composites increase with the increasing of filler contents at the same load

    我們認為，聚合物材料的摩擦系數變化除了與材料本身性能有關外，還與摩擦副的硬度有關。納米al _ 2o _ 3的加入，尼龍6的磨損量下降，但是對于尼龍6而言，存在一個最浙江
  13. Testing coated fabrics - method 16 - methods for determination of colour fastness to wet and dry rubbing and determination of resistance to printwear

    塗覆織物試驗.方法16 .濕摩擦和干摩擦色牢度及印花耐磨損性測定方法
  14. The degrees of crystallinity of pure ptfe under the different conditions of water cooling, air cooling and furnace - varying cooling were made comparison by xrd. the thermal stability of pure ptfe and solid lubricant was analyzed by dsc - tg ; the composition and valence state of elements in the surface of carbon fiber, solid lubricant before and after friction test and lubricant transfer film were characterized by xps ; the frictional property of solid lubricant was tested by pin and disk test rig. the frictional wear property of solid lubricant between embedded bearing sleeve and steel axle friction pair ring was tested by special simulate test machine, the hardness of solid lubricant was tested by pm ; the compression strength of solid lubricant was tested by material test machine

    用sem表徵原料微觀結構、摩擦表面及潤滑轉移膜表面形貌：用xrd進行原料物相分析，及比較水冷卻、空氣冷卻、隨爐冷卻三種工藝條件下的純聚四氟乙烯樹脂的結晶度；用dsc - tg分析純聚四氟乙烯樹脂及固體潤滑劑的熱穩定性；用xps表徵碳纖維表面、固體潤滑劑摩擦前後表面、潤滑轉移膜表面的元素組成、價態變化；用銷盤式摩擦磨損試驗機對固體潤滑劑進行摩擦性能測試；採用專用的臺架模擬試驗機對固體潤滑劑鑲嵌軸承套與鋼軸摩擦副間的摩擦磨損性能進行測定；用萊次偏光顯微鏡（ pm ）測試固體潤滑劑的硬度；用材料試驗機測試固體潤滑劑的抗壓強度等。
  15. Cutaneous : most about 95 percent anthrax infections occur when the bacterium enters a cut or abrasion on the skin, such as when handling contaminated wool, hides, leather or hair products especially goat hair of infected animals

    以下是疾病控制中心列出的各種炭疽熱的癥狀：皮膚性炭疽熱：大約95 %的炭疽熱患者是通過皮膚接觸感染病菌的，炭疽熱桿菌通過被切開或磨損的皮膚進入生物體內。
  16. We manufacture wear - proof especially used in cfbboiler where environment is badly corrosion at high temperature and rapid scouring of inflamer, plenty of advantages lies in against sulfur, fine coke - resistant, high temperature - resistant and wear - proof

    我公司針對cfb鍋爐高溫強腐蝕燃燒物劇烈沖刷等特殊環境，研製生產的專用耐磨熱電偶，具有耐硫耐焦粉耐高溫耐磨損性能。
  17. Diamond - like carbon gradient film on ti6a14v alloy substrate have been prepared by means of plasma source ion implanted - ion beam enhanced deposition ( psii - ibed ). for potential applications as artificial joint materials and artificial cardiac valve materials, its trobological performance and hemocompatibility has also been evaluated in the present ph. d. thesis

    本研究採用等離子源離子注入?離子束增強沉積技術（ psii - ibed ）制備了鈦合金基類金剛石梯度薄膜材料，對類金剛石梯度薄膜這一新型人工關節材料和人工心臟瓣膜材料的生物摩擦學性能和血液相容性進行了研究和評價，研究了摩擦磨損對材料血液相容性的影響。
  18. Implants for surgery - wear of total knee - joint prostheses - loading and displacement parameters for wear - testing machines with displacement control and corresponding environmental conditions for test

    外科植入物.全部膝關節假肢的磨損.帶位移控制和相關試驗環境條件的磨損試驗機械的負載和位移參數
  19. Implants for surgery - wear of total knee - joint prostheses - part 1 : loading and displacement parameters for wear - testing machines with load control and corresponding environmental conditions for test

    外科植入物.全膝關節假體的磨損.第1部分:試驗用有負荷控制和相應環境條件的磨損試驗機的負荷和位移參數
  20. The progress in the research on the mechanical properties, mechanism of tribological wear, biological compatibility and microstructure of carbon fiber ( cf ) reinforced polyether - ether - ketone ( peek ) composite is reviewed in this paper

    摘要綜述了碳纖維增強聚醚醚酮（ peek ）復合材料在機械力學性能、摩擦磨損機理、生物相容性、微觀結構等方面的研究進展。
分享友人
分享到 Line

分享到臉書