磨粒磨損 的英文怎麼說

中文拼音 [mólìmósǔn]
磨粒磨損 英文
abrasive wear
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 粒 : Ⅰ名 （小圓珠形或小碎塊形物） small particles; grain; granule; pellet Ⅱ量詞（用於粒狀物）
  • 損 : Ⅰ動詞1 （減少） decrease; lose 2 （損害） harm; damage 3 [方言] （用尖刻的話挖苦人） speak sarcas...
  • 磨損 : wear and tear; abrasive wear; abrase; abrade; detrition; wear; scuff; wear out; fray; battering; ...
  1. The pulse pneumatic conveying system has been a important transporting method for grain material, because of lower velocity, higher ratio of blend and a littler gas, as well as shattering less materiel, abrasing pipeline and easy recovery

    脈沖氣力輸送裝置以其低速、高混合比、低耗氣量等一系列持點，並由此帶來的被輸送物料破碎少、管道磨損小、產生粉塵少並且易於回收等優點，成為新一代粉粒料氣力輸送設備，並且被廣泛使用。
  2. Erosion of pipes and vessels from abrasion by particles can be serious.

    由於固體顆粒的磨蝕作用，管子和容器的磨損嚴重。
  3. For measuring abrasion of catalyst particles, three basic attrition test apparatus are used.

    為了測定催化劑顆粒的磨損，可使用三種基本磨損測試裝置。
  4. Abrasive wear may be defined as damage to a surface by a harder material.

    磨粒磨損可定義為較硬的材料對一個表面的破壞。
  5. This control requires knowledge of attrition kinetics and cyclone effectiveness.

    這種控制要求顆粒磨損動力學和旋風分離器效率的知識。
  6. The research results show that, from the viewpoint of second phase morphologies, there exist quite differences between the grain - type materials ( such as wc / bcu brazing deposit material, wrs1000 and 1zt tungsten carbide strengthening overlaying material, as well as the wear - resistant material of polymer adhesive coating etc. ), and the aggregation - type as well as dispersion - type ones ( such as zg35simn, wrd - 1 and khc - k2 depositing material ) in the wear - resistance and sand slurry abrasion mechanism. the sand slurry abrasion mechanisms are brought forward, of new wear - resistant materials with the features of grain - type second phase morphologies

    研究發現，與聚合型、彌散型第二相的材料（如zg35simn 、 wrd ? 1和khc ? k2熔敷材料等）相比，顆粒型第二相的材料（如wc bcu釬焊熔敷耐磨材料、 wrs1000型耐磨材料、 1zt碳化鎢顆粒增強熔敷材料及ktc ? 1耐磨膠粘塗層材料等）在耐磨性能和磨損機理等方面均有不同，總結提出了以「顆粒型第二相」為特徵的耐磨新材料泥沙磨損機理。
  7. In this paper, the principle of debris monitoring and analysis system ( dmas ) is introduced in detail, and the realization of the micrograph collection system and the wear fault integrated diagnostician system is also studied

    本文主要研究dmas磨粒監測與分析系統的工作原理以及顯微圖像採集系統和磨損故障綜合診斷專家系統的具體實現，以工程應用為背景，主要開展了以下方面的研究工作。
  8. Through the analysis of debris shape micrology, this paper constructed a describing system of fractal parameters and identified them effectively

    摘要主要介紹基於形態學方法的磨粒顯微分析與綜合識別技術，及其在發動機磨損狀態監測與故障診斷中的應用。
  9. When incorporation content of nano - al2o3 is 20 phr, fillers show conglomeration, which reduces the ability of fillers to link the molecular chain of pa6

    因此，為了提高填充粒子與基體的結合能力，有效的降低材料的磨損，對填充粒子作有機化處理是必要的。
  10. Conglomeration of fillers also easily fall off from the matrix, and all these result in wear mass loss increasing. the worn surfaces of the composites having 5 phr, 10plir, 20 phr nano - al2o3 are respectively studied by using the scanning electron microscopy ( sem )

    另外，在相同滑動條件下，隨著粒徑的增大，尼龍6 / a120 :復合材料的磨損量上升，納米級粒子填充的復合材料較微米粒子填充的復合材料耐磨性能要好。
  11. Effect of secondary flow on erosion from solid particles in 90 curved duct of quadrate section

    彎管內二次流對固粒磨損壁面的影響
  12. Development of abrasive wearability surfacing electrode based on tic - vc

    的抗磨粒磨損堆焊焊條
  13. The method can be adopted to research micro dynamic behavior and changing of friction surface and to show mechanism of abrasive wear

    為研究摩擦表面上的微觀動態行為與變化，認識磨粒磨損機理，提供了一種基於微觀數值模擬的途徑和方法。
  14. Standard test method for carbon black, pelleted fines and attrition

    碳黑球狀細粒磨損的標準試驗方法
  15. Analysing the wear mechanism of abrasive. adhesive wear. 2

    對磨粒磨損和粘著磨損的磨損機制進行分析。
  16. In order to analyze a micro cutting process of abrasive wear by means of molecular dynamics simulation, the principle, model and solving algorithm of molecular dynamics simulation of micro cutting process were discussed

    摘要針對磨粒磨損中微觀切削過程，研究了分子動力學模擬的基本原理、磨粒微觀切削過程的分子動力學模擬模型和數值模擬勢法。
  17. This paper analyzes the causes for the leakage of low temperature economizer in no. 7 boiler, and that was mainly due to ashes wear, secondly economizer design and installation of the existence smoke corridor, so that the wear is intensified

    摘要通過7 #鍋爐低溫省煤器泄漏的原因，指出主要是灰粒磨損所致，其次為省煤器設計安裝時存在煙氣走廊使磨損加劇。
  18. Fluid machinery in these areas is damaged due to cavitation and sand abrasion, which has threaten directly the safety operation of hydraulic and hydroelectric engineering, causing huge economic losses. the research, therefore, on the combined effect of cavitation and sand abrasion is of great significance. the researchers at home and abroad have done a lot of work on this issue

    我國許多河流的含沙量較大，如著名的黃河幹流年均含沙量達37 . 9m ~ 3 / s ，黃河三門峽的年平均輸沙量達16億t ，這些地區使用的泵、水輪機等許多流體機械都在夾沙水流的作用下，受到了沙粒磨損與空化剝蝕的聯合破壞，這種破壞直接危害了水利水電工程的安全運行，造成了巨大的經濟損失，因而對含沙水流條件下空化剝蝕與泥沙磨損聯合作用進行研究有著很大的工程實際意義。
  19. Microstructure and properties of abrasive wearability hardfacing welding based on tic - vc

    耐磨粒磨損堆焊的顯微組織與性能
  20. Volume of wheel grain wear

    磨輪顆粒磨損體積
分享友人
分享到 Line

分享到臉書