稱量槽 的英文怎麼說
中文拼音 [chènliángcáo]
稱量槽
英文
weighing tank-
2 ) the structure elements should be laid out symmetrically and uniformly when designing steeve - arch structure, what ' s more, the reasonable selection of section geometric size near the arch foots of first beams is paid attention to and the arrangement difficulties of steel bar due to the big eccentric pressures 2, the analyses of anti - seismic features on transverse direction of the aqueduct l ) the method of adjusting the elements " mass can be harnessed in order to even the layout of seismic loads
2 ）設計吊桿式拱架支承結構時，各部分構件應當均勻對稱布置。另外，還應注意頭道梁拱腳附近截面的尺寸擬定，克服地震內力造成的大偏心受壓狀態給結構配筋設計增加的困難。 2 、橫槽向抗震性能分析1 ）可利用調整構件質量的方法，使得結構的某些構件的地震荷載分佈均勻一些。Abstract : a new waveguide which can change the wide wall of a rectangular waveguide into a symmetric arc wall is named as a cam - rectangular waveguide. comparing to sectoral waveguide, the new waveguide has the same voltage characteristics and is easier to be produced and fixed. an approximate formula of the dominant mode fields and the normalized conductance of a longitudinal resonant slot cut in the curved wall of a cam - rectangular waveguide are given. a resonant slot linear array in c & x band is designed, in which the slot voltage distribution is equiphase and the input is matched. the input voltage stationary ware ratio and the h - plane pattern of the antenna are measured. the experimental results show the conformance with theoretical results
文摘:把常用的矩形波導一個寬面改成圓弧形構成的波導稱為圓突-矩形波導.這種波導與扇面波導相比：電性能相當；波導管結構更加簡單，容易加工，便於安裝.文中給出圓突-矩形波導中主模場，圓曲面上縱向槽歸一化諧振電導近似公式.設計了c和x波段波導曲面縱向諧振縫隙線陣，縫隙電壓相位為同相分佈，輸入端匹配.實際測量了天線輸入端電壓駐波比和h面方向圖，理論與實驗相吻合This dao is estimated to be around 60cm long ( very short, it can ' t be measured accurately without ruler at home ) and two fingers wide ; intact scabbard and fittings with perfect appearance ; no collapse on blade, little rust ; stretchy ; there ' s buff pattern - shape rust spots appeared after polishing several minutes which should be so - called pattern steel ; regular and symmetrical blood groove
該刀刀長估計只有60公分左右（很短小，家裡沒尺不能準確的量） 、寬兩指；刀鞘和裝具完整且品相極佳；刀刃無崩口、卷刃、銹很少（任何地方都可以削鉛筆） ；彈性十足；磨了以後幾分鐘即出現淺黃色銹斑，呈花紋狀，應是所謂花紋鋼；血槽非常工整、對稱。Based on in - depth analysis on characteristic and function principles of psd, combined with characteristic of measured object, this article presents an new real - time measurement for symmetrical degree, guiding - groove, twining angle, inside radius of long direction pipe ; completes designing work for hardware of function module and application software ; and gives analysis and computation on error sources and uncertain - degree of measure result. based on above work, this article develops a parameter - auto - chosen, integrated and automatic measurement device for beeline degree, guiding - groove symmetrical degree, twining angle and inside radius of long direction pipe
本文在深入分析研究psd的特點和工作原理的基礎上，結合被測量對象的特點，首次提出了長定向管導槽對稱度、纏角、內徑等實時自動化測量的一種新方法；完成了硬體功能模塊及應用軟體的設計工作；並對測量結果的誤差源及不確定度進行了分析和計算；在此基礎上研製了長定向管的直線度、導槽對稱度、纏角及內徑等參數自動、實時綜合測量設備。With the siemens plc s7 - 300 and the corresponding programming software step7, that helps in control software programming, the proportioning system meets the requirements of automatic proportioning, weighing, loading and weight compensating. the design work uses wincc, that is also a product from siemens, to configure the supervisory software, realizing the real - time data - logging, supervising and controlling, as well as various visual hmi with windows features such as real - time weighing, record checking, alarming, dynamic simulation
該項目採用的是德國siemens公司的s7 - 300系列plc ，運用與之相配的step7編程軟體，通過stl和lad兩種編程語言編制了下位機的控製程序，從而使該槽下配料系統可以按要求自動完成配料、稱量、裝料全過程，並自動實現稱量補償。分享友人