穩度力臂 的英文怎麼說
中文拼音 [wěndùlìbèi]
穩度力臂
英文
stability lever-
Lifting and lowering of the pringting arm of this machine is vertical, therefore, in case of half - tone printing, presence of screen wire and consistency of aberration are improved ; in case of spot printing, stability and uniformity of inking are enhanced ; fine adjustment and lock of the worktable is independent of each other, so positioning error caused by lock of the worktable can be controlled ; height and pressure of the printing blade and ink - returning blade can be stepless - regulated separately, which improver printing quality and service life of half - tone ; printing travel and half - tone fixing mechanism can be fast adjusted, which is suitable for printing area with different size
本機印刷大臂升降為垂直升隆式，網線版印刷時網線表現率為色差一致性得到提高，實地版印刷的施墨穩定性及均勻性得以加強；工作臺微調與鎖緊獨立，因工作臺鎖緊而帶來的定位誤差得以控制；印刷刀、回墨刀高度及壓力均可單獨無級調節，提高了印刷質量和網版的使用壽命，印刷行程和網版固定機構大小可快速調節，方便不同規格的印刷面積。For a project instance, it computes and analyzes the structure of madian radial gate with fem, which achieves the result of gate ' s structural stress, stiffness and surpport - bar ' s stability and gives comparative analysis
作為工程實例，對馬甸弧形閘門的結構進行了有限元計算和分析，得到了閘門的結構應力、剛度以及支臂穩定的計算結果，並給予了比較分析。In this part, it is also found that the equivalent prismatic column, which is obtained based on the equal elastic critical load as the non - prismatic member, is not actually equivalent to the tapered column in inelastic stability, and the latter has higher load carrying capacity. finally, the behavior of tapered beam - column acted by combined axial load and transverse load has been investigated. a bending - thrust interaction curve is established which is similar to the ones for the design of prismatic members
三是研究了楔形變截面懸臂構件在大端固定，小端同時承受橫向及軸向荷載共同作用下的強度和彎矩平面內的穩定，同時參考等截面構件的設計公式，得到了用大端截面來表示的軸力p與彎矩m的之間的相關關系。The theoretical analysis shows that mz - ifog can be used to detect the rotation rate of moving objects. a systematic analysis of transfer characteristics of mz - ifog is made. performance - limiting factors, including the path - length difference, the disturbance of temperature fluctuation and stress from working environment, the quality of light source, are all discussed along with methods to reduce their effect on the output signal
本文用系統的方法分析了mz型干涉式光纖陀螺儀的光傳輸特徵，指出了其較大的非互易性因素-臂長差的存在，分析了工作環境因素（溫度，應力） 、光源質量（輸出光束中心波長、光功率波動及偏振態波動）對系統工作性能的影響，並指出了減少系統非互易因素、抑制噪聲、提高檢測穩定性的措施。Lever of weight stability
重量穩度力臂Standard for minimum splitting strength and compressive strength of cement - treated aggregate is suggested based on laboratory testing results of material and mechanical analyses with bisar software during construction
摘要根據水泥穩定碎石混合料的室內試驗結果及其在路面結構和施工階段的受力狀況分析，提出了水泥穩定碎石基層的最低臂裂強度和抗壓強度建議標準。Improvement on pupils ' attention by the application of a hand and arm stability machine
應用手臂穩定度儀提高小學生注意力的實驗研究In addition, aerodynamic stiffness and aerodynamic damping on the system are already obtained in the condition of fluid - structure interaction. it is known that aerodynamic loads are associated with blade vibration. the systematic eigenvalues are used to judge whether the flutter occurs so as to find the stable operating range of a wind turbine
本文把風力機葉片簡化為懸臂梁，對梁截面的二維葉型建模，完整推導了二維葉型的線性運動微分方程和流構耦合條件下系統的氣動剛度和氣動阻尼，此時氣動載荷與結構的位移矢量以及速度矢量是相互耦合的，再利用系統的特徵值來判斷葉片顫振是否發生，從而獲得風機的穩定工作范圍。This paper conducts a study of nonlinear stability behavior of a long - span prestressed concrete rigid - frame bridge at cantilever construction stage respectively by means of buckling, collapse theories and 3d nonlinear digital models, discusses the stability characteristics of other similar bridges at the same construction stage, and also generalizes some helpful conclusions
摘要分別採用屈曲理論和壓潰理論，利用三維非線性數字模型，研究了懸臂施工階段大跨度預應力混凝土剛構橋的非線性穩定行為，探討了同類橋梁懸臂施工階段的穩定性，得出了一些有益的結論。分享友人