穿透速率 的英文怎麼說

中文拼音 [chuāntòusùlǜ]
穿透速率 英文
penetrating rate
  • 穿 : Ⅰ動詞1 （破; 透） pierce through; penetrate 2 （通過孔、隙、空地等） pass through; cross; go thro...
  • 透 : Ⅰ動詞1 （滲透; 穿透） penetrate; pass [seep] through 2 （暗地裡告訴） tell secretly; let out; lea...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 穿透 : （貫穿） penetrate; pierce through; pass through; penetration; transmission; piercing
  • 速率 : speed; rate; tempo
  1. The results showed that the torque ratio and efficiency curve are almost not affected by width ratio, whereas the torque capacity performance changes especially when the speed ratio is less than 0. 6

    結果表明，隨寬度比減小變矩比和效率基本不受影響，而透穿性則由正透穿逐漸變為混合透穿，在速比大於0 . 6時傳動性能基本沒有差異。
  2. Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )

    本研究以武裝直升飛機防護裝甲材料為研究對象，採用真空熱壓粉末冶金燒結工藝制備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料，結合其力學性能、掃描電鏡和界面微區能譜分析結果，分析了sic _ p al復合材料的真空燒結過程中的界面現象，以及材料增強和斷裂機理，並利用hopkinson高速壓桿沖擊實驗系統對其從靜態到動態（應變率為3 . 3 10 ~ （ - 3 ） s ~ （ - 1 ） 5 . 2 10 ~ 3s ~ （ - 1 ） ）的壓縮破壞響應進行了研究，分析了不同體積分數sic _ p al復合材料高應變率壓縮載荷下，材料的變形和微觀損傷機理，以及利用高速沖擊空氣炮測定了改復合材料制備剃度復合板的穿透性能。
  3. Although skin can be a relatively impermeable barrier, a few drugs have just the right physical and chemical characteristics to cross it at reasonable rates

    雖然皮膚是相當不易穿透的障礙，但少數藥物的物理化學特性，恰好能讓這些藥物以合理的速率穿過皮膚。
  4. Compared with conventional weld methods, electron beam welding possesses such advantages as high power density, strong penetrability, precise, high speed, good control ability, good protection effect and high quality

    與常規的焊接方式相比，電子束焊接具有功率密度高、穿透能力強、精確、快速、可控性好、保護效果好、焊縫質量高等優點。
  5. This machine is flowing and continuous type drying equipment firstly made by our factory. the machine is used for drying the piece, tape and particle state materials with good ventilation. the machine is suitable for the materials, such as de - watering vegetable. herbal medicine of traditional chinese medicine and others, for which the water content rate is high and the high temperature is not allowed. the machine owns the advantage, that its drying speed is fast, the evaporation strength is high and the product quality is good. the de - watering filtering cake state paste material, after the particle making or bar making, can be dried also

    該機是穿流連續式乾燥設備，用於透氣性較好的片狀、條狀、顆粒狀物料的乾燥，對于脫水蔬菜，中藥飲片等含水率高，而溫度不允許高的物料龍為合適；該系列乾燥機具有乾燥速度快，蒸發強度高，產品質量好的優點，對脫水濾餅狀的膏狀物料，需經造粒或製成棒狀后亦可乾燥。
  6. The result of the experiment indicated that the capability of adsorption decrease with ultrasound intensity, while the rate of the extraction and adsorptin increase. the model resulst also showed that the theoretical value of the homogeneous model considering intrapartical diffusion and outside - surface diffusion with freundlich phase equilibrium equation are agfeeable with the experimental value

    在吸附實驗中，測定了不同強度超聲場下梔子甙與1300樹脂上吸附平衡曲線、靜態吸附動力學曲線、動態穿透曲線。實驗結果表明，吸附容量隨著超聲波強度的增加而減少，而浸取、吸附速率隨著超聲波強度的增加而增大。
  7. Abstract : a previously proposed approximate quasi - static theoretical method is employed herein to examine the deformation and perforation of a simply - supported circular plate struck by a flat - faced projectile at normal incidence. based on the principle of virtual work, static load - displacement relationships are first obtained and then used to predict the energy - absorbing capacity of the plate subjected to relatively low speed impact. it is shown that good agreement is obtained between the theoretical predictions and the available experimental data, provided that adiabatic shear plugging failure does not occur, but the influence of strain rate sensitivity is taken into account

    文摘:採用準靜態近似理論方法分析簡支圓板在平頭彈丸正撞下的變形和穿透.首先基於虛功原理得到了靜態荷載位移關系，並將其用於預測低速沖擊下圓板的能量吸收能力.當考慮了材料的應變率敏感性，並且不發生絕熱剪切沖塞破壞的前提下，理論預測和實驗結果吻合良好
分享友人
分享到 Line

分享到臉書