穿通電壓 的英文怎麼說

中文拼音 [chuāntōngdiànyā]
穿通電壓 英文
punch through voltage
  • 穿 : Ⅰ動詞1 （破; 透） pierce through; penetrate 2 （通過孔、隙、空地等） pass through; cross; go thro...
  • 通 : 通量詞（用於動作）
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 壓 : 壓構詞成分。
  • 電壓 : voltage; electric tension; electric voltage
  1. This heating helps to break down weak spots in the dielectric that otherwise might pass through the electrode undetected, only to fail during a later spark or hipot test

    這熱量幫助擊穿電線絕緣較薄的地方?否則線材通過電極而沒有被檢測到?結果在以後的火花測試和高壓絕緣試驗將會失效。
  2. In order to improve process quality and increase probability, we optimize ohm contact resistance and breakdown voltage of devices by adjusting process conditions. finally, dc - 500mhz midf switch is fabricated, in which some important conclusions and suggestions are introduced

    工藝研究的重點是改進工藝質量，提高成品率，為此我們通過調整工藝條件來優化歐姆接觸電阻和提高器件的擊穿電壓。
  3. Author analyzed the relationship between the length and the impurity concentration of drift region and thickness of buried oxide layer and thickness of soi and the charges of oxide layer and bias voltage of bulk and breakdown voltage and on - resistance by numerical simulation

    採用數值模擬分析方法，深入研究了漂移區長度、漂移區濃度、埋氧層厚度、頂層硅厚度、氧化層電荷以及襯底偏壓對resurf效應、擊穿電壓和導通電阻的影響。
  4. The main work is done with the help of model experiment. in the flood - relief experiment, the flood carrying capacity of spillway tunnel is checked. in the hydraulic experiment of the diversion power conduit system, the followings are studied : the flow condition and fluctuation in the surge chamber, the distribution of flow velocity before the rack in the surge shaft, the amplitude of stage in the quick gate bay etc. the test step, content and results of different proposals are introduced in details

    本項優化試驗研究的目的主要在於，通過泄洪系統整體水力學試驗，校核泄洪洞的泄流能力；通過發電引水系統整體水力學試驗，研究調壓井內水流流態和水位波動情況、調壓井內攔污柵前流速分佈情況；確定快速閘門井內水位波動幅度；試驗確定壓力管道水擊壓力穿井系數以及泄洪洞弧形門處的水壓力。
  5. Test results indicated : with the hoist of altitude, the increase of ice amount and the rise of pollutant, the average flashover voltage reduced. the character exponent generally depends on the insulator profile, ice amount, ice state and pollution severity etc. by means of a high - speed camera, a data acquisition system and high voltage test facilities, a series of the flashover processes on ice surfaces were record. the experimental results form this study and the subsequent theoretical analyses suggested : the thermal ionization of the air in front of an arc root resulted in arc movement ; the electrostatic force had an auxiliary effect of impelling arc propagation ; the electrical

    通過對攝像機、數據採集系統及高壓試驗裝置記錄覆冰絕緣子表面閃絡電弧的發展過程的試驗結果進行理論分析得出：弧根周圍空氣的熱電離導致了電弧的發展，靜電場力對電弧的發展起到了加速作用，電擊穿僅發生在閃絡最終的跳躍階段；通過測量閃絡過程中的放電電壓、泄漏電流、閃絡時間、覆冰水電導率、電弧長度及電弧半徑等參數，得到了不同階段電弧（電弧起弧階段、電弧發展階段及完全閃絡）的發展速度、臨界電弧長度均隨覆冰水電導率的增加而減小。
  6. It also put forward that how to select appropriate epilayer doping concentration and thickness, pn junction depth and jte technology to increase the breakdown voltage of 4h - sic mps. a power dissipation model of 4h - sic mps was established

    通過對4h - sicmps擊穿特性的二維模擬，提出如何選擇合適的pn結深度、外延層摻雜濃度和厚度以及如何運用jte終端技術來提高擊穿電壓。
  7. In this paper, the theory of negatively charged surface states is used to investigate dynamic breakdown characteristics and the increase of gate - drain breakdown voltage as well as the reduction of saturated drain - source current after sulfur passivation. the measure which can improve the stability of sulfur passivation is proposed

    本論文通過對gaasmesfet擊穿機理和硫鈍化機理的研究，用負電荷表面態理論，解釋了gaasmesfet動態擊穿特性及硫鈍化后柵漏擊穿電壓增大、源漏飽和電流減小的機理，提出了改善硫鈍化穩定性的措施。
  8. The result of numerical simulation indicated the tradeoff of breakdown voltage and on - resistance. the selection of structure prefer the thicker buried oxide layer and the thicker soi layer and the shorter drift length when the breakdown was happened at the interface of soi and buried oxide layer

    模擬結果表明，擊穿電壓與導通電阻存在明顯折衷關系，因此在選擇器件結構時要選擇埋氧層厚度大，漂移區濃度高，在保證擊穿發生在縱向的情況下，漂移區長度越小越好。
  9. Particle - carrying air enters the bag filter via the inlet, passing through a stopper ; at this point, heavier powders settle first, while lighter powders attach to the filter evenly ; the plc then controls the electromagnetic valve to trigger the membrane valve for input of pressurized air, which passes the venturi tube to flush the filter by shaking off powders into the collection chute, whereas the clean air passes through the filter to be released by the fan

    控制電磁閥導引膜片閥輸入壓縮空氣，使其通過文氏管對濾袋進行噴洗，使得附著于濾袋四周之粉塵震落於集灰槽內，而乾凈空氣則穿透濾袋藉由送風機排出。
  10. The essentially universal biophysical phenomenon of " electroporation " occurs if an appropriate pulse field is applied. electroporation is believed to be the rapid creation of aqueous pathways through lipid - containing barriers in cells and tissue. the driving force is the physical interaction of electric fields with different dielectric constants

    電穿孔效應是指在適當高壓脈沖電場作用下，細胞或組織間起相對隔離作用的「屏障」內快速形成液態通道的現象，是電場與具有不同介電常數而且易變形的物質相互作用的結果。
  11. According to the thickness of the soi film, high voltage ic based on soi material ( soi - hvic ) can be divided into thin - film and thick - film. for thin - film soi - hvic, linear drift region doping profile is adopted to satisfy a certain breakdown - voltage, but this process is too complex and its self - heating effect is obvious ; for thick - film soi - hvic, it can take advantage of cmos technology on silicon to obtain the high voltage

    Soi高壓集成電路根據頂層硅厚度可分為厚膜和薄膜兩大類。為了滿足一定的擊穿電壓，薄膜soi高壓電路一般採用漂移區線性摻雜技術，但其工藝復雜，且自熱效應嚴重;而厚膜soi高壓集成電路可以通過移植體硅cmos技術來實現高壓，但是由於其硅膜較厚，介質隔離成為厚膜soi高壓集成電路的關鍵技術。
  12. The conclusion that ez is more important during the breakdown of rf ion source is made out by comparing ez and e 6 before breakdown, and then, the breakdown criterion of rf ion source is deduced, and the relation between breakdown voltage and pressure is analyzed too

    通過比較擊穿前高頻電場的軸向和幅向分量，得出了軸向電場在高頻離子源擊穿中起主要作用的結論，並進而推導出了高頻離子源的擊穿判據，得出了氣體擊穿時離子源擊穿電壓和放電管內氣壓的關系。
  13. Through the relations of temperature - time, pressure - time and pressure - breakdown voltage, the relation between the breakdown voltage in different stages and time is derived

    通過金鹵燈的溫升?時間關系、氣壓?時間關系以及壓力?擊穿電壓的關系，得出了金鹵燈在不同階段的時間?擊穿電壓的關系。
  14. Aqueous fluid volume and [ c1 ~ j were assayed in samples withdrawn by micropipettes. intraocular pressure ( top ), pressure - dependent outflow, and anterior chamber compliance were determined from pressure measurements in response to pulsed and continuous fluid infusions into the anterior chamber using micropipettes. result : in wildtype mice ( gdi genetic background, age 4 - 6 weeks ), iop was 16. 0 ? 0. 4 mmhg, aqueous fluid volume was 7. 2 ? 0. 3 ul, aqueous fluid production was 3. 6 ? 0. 2 ul / hr, aqueous fluid outflow was 0. 36 ? 0. 06 ul / hr / mmhg, and anterior chamber compliance was 0. 036 ? 0. 006 ul / mmhg ( mean ? se, 8 - 10 eyes )

    實驗方法包括：將熒光物質用電離子滲透的方法穿透角膜導入活體小鼠的前房中，然後應用共聚焦顯微鏡根據熒光強度變化測量房水生成率；通過顯微注射針吸取房水檢測房水容積和氯離子濃度；顯微玻璃管刺入前房測量眼內壓，並將生理鹽水分別以連續和脈沖兩種方式注入前房，測量房水間隙的順應性和房水排出與眼內壓的相關性。
  15. Jdy - 280b double electromagnetic lock product characteristic : strong holding force, no left magnet easily installed, low noise, durable no mechanical failure with signal feed back function applications : can be used with intercoms and access control systems, especially for fireproof door working voltage : 12vdc 24vdc working current : 12vdc 0. 27a, 24vdc 0. 46a power consumption : 3. 3w, 3. 5w, absolutely insulative power supply mode : successively working temperature : - 40 50 dimension : 473 x 45 x 30mm weight : 3920g yiwu qimingxing computer company copy right

    Jdy - 280b雙開門磁力鎖產品特性:吸力強無剩磁安裝方便噪音低壽命長具故障保護功能，無機械故障可具資訊回饋功能鎖狀態有指示燈指示：鎖門時綠燈指示燈亮開門時，紅色指示燈亮帶鎖狀態指示燈及聯網信號輸出適用范圍：可與樓宇對講門禁系統配套使用特別適用於逃生門防火門電氣性能：電氣性能：使用電壓： 12vdc 24vdc電流： 12vdc 0 . 53a 24vdc 0 . 27a絕緣電阻測試： dc500v 1分鐘無擊穿通電形式連續使用溫度： 40 50外形尺寸： 473 x 45 x 30mm重量： 3920g
  16. For the first time, the energy band configuration of p - si / n - bn heterojunctions were studied and drawn up. the study of the current - voltage ( i - v ) characteristics showed significant rectifying behavior with reverse saturation current of 3. 7 x 10 ~ 7a, breakdown voltage of 30v and turn on voltage of 14v. the capacity - voltage ( c - v ) characteristics are studied too

    研究了p - si / n - bn異質結的-特性，測試表明異質結具有明顯的整流特性，反向飽和電流3 . 7x10 「 』 a ，擊穿電壓高達30v導通電壓為14v ，應用p七en異質結能帶圖對其卜v特性做出了定性解釋。
  17. The research of the effect of soi s - resurf included the impact of the geometry parameters and drift doping concentration on breakdown voltage and on - resistance

    Soisingle - resurf效應研究。研究了soisingle - resurfldmos的器件參數對擊穿電壓和導通電阻的影響。
  18. Abstract : the saturation behavior of stress current is studied. the three types of precursor sites for trap generation are also introduced by fitting method based on first order rate equation. a further investigation by statistics experiments shows that there are definite relationships among time constant of trap generation, the time - to - breakdown, and stress voltage. it also means that the time constant of trap generation can be used to predict oxide lifetime. this method is faster for tddb study compared with usual breakdown experiments

    文摘:基於一階速率方程，討論了恆定電壓應力下應力電流的飽和行為.通過對應力電流的擬合，發現存在三類缺陷產生的前身.更進一步的統計實驗顯示，在缺陷產生時間常數、擊穿時間以及應力電壓之間存在著明確的關系.這意味著缺陷產生時間常數能夠被用於有效預測氧化層的壽命.與常規的氧化層擊穿實驗相比，基於缺陷產生時間常數的預測更快、更有效
  19. In this paper, the over voltage induced by re - ignition, rules of breakdown in vacuum contact clearance, factors which influence dielectric strength of clearance and characteristics of re - ignition when vacuum switchgear switch capacitor banks are analyzed. the conclusion is that the breakdown of clearance in vacuum interrupter is the direct cause which inducing re - ignition of vacuum circuit - breaker in capacitor banks ’ switch. particle breakdown is the essential reason to induce breakdown in clearance of vacuum interrupter, although mechanical characteristic of vacuum circuit - breaker is another factor

    本文通過對真空開關投切電容器組重燃過電壓、真空觸頭間隙擊穿機理及影響真空間隙介質強度的因素、真空開關投切電容器組重燃現象特點進行分析研究發現，真空滅弧室斷口的真空間隙擊穿是導致真空斷路器投切電容器組重燃的直接原因，其次是真空斷路器機械性能的影響，而微粒擊穿是導致國產真空滅弧室真空間隙擊穿的根本原因。
  20. According to calculation, synchronous closing can reduce the value of over - current and over - voltage in the closing transient process. the closing of capacitor is taken as an example to analyze movement process of synchronous closing. it also analyzes the impact of pre - strike characteristic, environmental temperature and control voltage on synchronous closing

    通過計算分析了同步關合技術對合閘暫態過程中過電流和過電壓的抑制作用，並以電容器的同步關合為例，分析了同步關合的動作過程及預擊穿特性、環境溫度，控制電壓等外界因素對同步關合技術的影響。
分享友人
分享到 Line

分享到臉書