窗槽口 的英文怎麼說

中文拼音 [chuāngcáokǒu]
窗槽口 英文
window groove
  • 窗 : 名詞（窗戶） window
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 口 : Ⅰ名詞1 （人或動物進飲食的器官; 嘴） mouth 2 （容器通外面的地方） mouth; rim 3 （出入通過的地方） ...
  1. Boys from high school are perched on the lampposts, telegraph poles, windowsills, cornices, gutters, chimneypots, railings, rainspouts, whistling and cheering. the pillar of the cloud appears

    高中的男生們蹲在街燈柱電線桿窗口檐口檐槽煙囪頂管欄桿和排水管上，又是吹口哨，又是歡呼出現了雲柱205 。
  2. Wallet with retractable id sleeve, id slot with monofilament window, internal key holder slot, three horizontal and three vertical card slots, extra storage slot, bill compartment with divider, quilted accent with heavy - gauge thread on exterior leather, embroidered icon, and metal bar logo accent

    錢包與可撤回的身份證袖子，身份證槽孔與單絲窗口，內部關鍵囤戶槽孔，三個水平和三個垂直的卡片槽，額外存貯槽孔，票據隔間以分切器，縫制了口音與重測量螺紋在外部皮革、被繡的像，和金屬棒商標口音。
  3. In this way, when obturation cubage leave absorb oil cavity it connects the eduction oil cavity with the v trough and with the increasing of the turning angle, the size of the cross section of v trough become bigger and bigger, which make the pressure between the cavity of two blades much higher and higher, and until it completely connects the eduction oil cavity, it reaches the pressure of the eduction, and it can effectively reduces the fluid noise caused by high pressure return flow

    這樣，當密閉容積離開吸油窗口之後，通過v型尖槽逐漸與排油窗口連通，隨著轉角的增加， v型尖槽通流截面積逐漸增大，這就使兩葉片間容腔內的壓力逐漸升高，直至完全接通排油窗口時，才升壓達到壓油腔的壓力，這樣可以有效地降低因高壓迴流而引起的流體噪聲。
  4. The ratios of the flow rate ( q / q ) are 1. 4 1. 0 0. 6 respectively. three blade - to - blade passage and the three cross - section along the axial direction at each of the passages were selected for measurements

    測試窗口分別取在三個不同的葉槽中，在每個葉槽中沿軸向測試三個斷面和一個間隙斷面。
  5. This thesis discusses detailedly the flow process of ip multicast, error discovery method and error recovery method, and also proposes a new error control method to implement reliable multicast in computer supported cooperative design system : serial integrates with timer are used to discover error, arq mechanism based on nak feedback is modified to correct error, " sliding window " mechanism is imported to make up the drawbacks of traditional nak, and " slotting and damping " technique is used to resolve the question of " feedback implosion " which results from multicast reliability control

    詳細研究了ip多播傳輸的流程、數據傳輸的差錯檢測方法及差錯恢復方法，提出在協同設計系統中實現可靠多播的控制方法：利用序列號和計時器相結合的方法進行傳輸數據的差錯檢測，改進了基於nak反饋信息的arq重傳機制來實現差錯恢復，並引入了滑動窗口機制來解決傳統nak方法的不足，採用「時間分槽?抑制」技術來解決由於進行多播可靠控制而產生的「反饋內陷」問題。
分享友人
分享到 Line

分享到臉書