端位移 的英文怎麼說
中文拼音 [duānwèiyí]
端位移
英文
end movement-
On this foundation the article inducts in detail the method which is based on the relative settlement of calculating unit area end support ( qb ) force at the same time considering the feature of pedestal pile ' s " arch effect " the article introduces conception of pile effective length and finally obtain t he formula of calculating man - made pipe with bulb - shaped axial carrying capacity. the article uses marc program to calculate and analyze foundation soil ' s stress and displacement and gets the change curve chart and the proportion that is shared by king - pipe side soil friction resistance and pipe end counterforce respectively. the article inducts the structure of pedestal in detail on the basis of generalizing pedestal application cases of many countries
在此基礎上論文詳細歸納了以相對沉降為依據確定單位面積端承力q _ b的計算方法，並考慮擴底樁的「拱效應」特點引入了有效樁長的概念，最後結合公路規范推出了比較實用的人工挖孔擴底樁軸向承載力計算公式。論文運用了marc程序對地基土的應力和位移進行了有限元數值計算分析，得到了地基土的應力和位移場的變化曲線和在加載過程中樁側土摩阻力和樁端反力各自所承擔的比例；本文還在總結各國挖孔擴底樁應用情況的基礎上就擴底樁的構造進行了詳細的歸納。Research about ctod and its components 8 ", " shows that the direction angle of ctod vector is identical with the fracture angle of void - mode fracture, which is obtained through experiments, and it is also identical with the result got by peak value line of stress triaxiality. besides, 8 i " was compare with vgc as criterion for initiation of void - mode fracture
對裂紋尖端張開位移ctod及其張開型分量~ 1和剪切型分量~ 11的分析表明，在試件發生韌窩型斷裂時，按照圓弧裂紋中ctod矢量的垂直方向預測的斷裂角與試驗測得的斷裂角符合較好，與三軸度脊線預計的結果也比較一致。The experiment apparatus has been developed, which is based on software ( labview ) and hardware ( pci board ni 6024e ). the displacements and generative force at the tip of the ipmc actuators were measured with respect to the different voltages, frequents and various waveforms which include square, sinusoidal, and triangular wave
實驗選取了不同電壓幅值，不同頻率的方波、三角波、正弦波三種波形作為電激勵信號，利用高速攝像記錄ipmc的位移變形，並通過力傳感器實測了ipmc試樣末端的輸出力。The results of field observation showed that mucky clay in the shore slope of the wharfs was the stratum with the most obvious horizontal displacement and most of the pile heads close to the retaining walls inclined towards the land to different degrees, agreeing well with the inclination of pile heads as observed on site
原型觀測結果表明：碼頭岸坡內的淤泥質粘土層為水平位移最明顯土層，靠近擋土墻的大部分樁頂都出現了不同程度的向陸側傾斜，這與實際見到的樁端傾斜狀況完全相符。Then a vsc controller using on - off valve and two potentiometers are designed for cushioning control system. it can realize the balanced, no shock, no reversing cushioning. experiments under different air pressure, load mass are carried out, and the results prove that the vsc controller can be used in pneumatic cushioning
第五章首先介紹了變結構控制的原理和應用發展情況，然後針對本實驗系統設計了一個使用開關閥和端位位移傳感器的變結構控制方案，實現緩沖過程的平穩無沖擊和無回彈要求，並在不同氣源壓力、不同負載質量下分析了控制性能的變化，實驗結果證明緩沖控制採用變結構控制是可行的，並具有很強的魯棒性。The dynamic force - displacement relation curve is of crucial important to the design and operation of mechanical impact devices. using one - dimensional wave mechanics and characteristic line theory, this paper presents a testing method for determination of dynamic force - displacement relation curve from one - point strain measurement on an elastic rod endface. the principle of measurement, data processing method and experimental results for penetration into granite are discussed. 4figs., 5refs
沖擊載荷下彈性桿端的作用力-位移關系曲線是沖擊機械繫統研究的重要內容.基於一維波動力學方程，應用特徵線方法，探討了已知一點應變求取彈性桿端的作用力-位移曲線的測試原理與數據處理方法，以及在花崗巖上沖擊鑿巖機具的測試結果，對一點應變測試法的可行性進行了論證.圖4 ，參5( 2 ) according to the forming model of the deep pull cracks, they can be divided into three classes pulled cracks -, pressed cracks and sheared cracks. ( 3 ) based on the two - dimensional and three - dimensional finite element methods. the following results can be affirmed : in the slope excavating process, the base surface will rebound in the direction of the excavating surface ' s excerior normal. the maximal displacements of the left and right bank are + 3. 6cm and + 2. 4cm ; the arch abutment will rebound in the direction of the river valley, the maximal displacements of the two bank are + 3. 5cm and + 2. 2cm ; the upstream and downstream surface will rebound in the direction of the normal direction. the maximal displacements are + 2. 1cm and + 1. 7cm. ( 4 ) the natural slope is stable
（ 3 ）通過二維及三維有限元分析得知，左右岸拱肩槽邊坡在開挖過程中，開挖底面主要表現為朝開挖面外法線方向發生回彈，左右岸最大位移量分別為+ 3 . 6cm 、 + 2 . 4cm ；拱端面主要表現為向河谷方向發生側向回彈，左右岸最大位移量分別為+ 3 . 5cm 、 + 2 . 2cm ；上下游坡面主要表現為向臨空方向的回彈，左右岸最大位移量分別為+ 2 . 1cm 、 + 1 . 7cm ；開挖使巖體產生由卸荷回彈導致的傾倒拉裂現象。In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented
本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。According to the recorded full process fracture curve, the paper calculated and compared the fracture toughness ( kic ), the fracture energy ( gf ) and crack tip opening displacement ( ctod ) of the different strength grade boulder concrete and crushed stone concrete, it is found that the maximal load ( fmax ) and the fracture toughness ( kic ) of boulder concrete and crushed stone concrete increase when the strength of them increases, so does the fracture energy of boulder concrete, but the fracture energy of crushed stone concrete does n ' t obviously increase when it ' s strength increases. the crack tip opening displacement ( ctod ) of all specimens chang less when the strength of concrete increases, so it is concluded that the location of the axle in the ligament of the specimens is relatively stable
根據記錄的全曲線，計算了不同強度等級的卵石混凝土、碎石混凝土的斷裂韌度k _ （ ic ） 、斷裂能g _ f以及裂縫的尖端開口位移ctod ，比較了不同強度等級卵石混凝土及碎石混凝土的斷裂韌度k _ （ ic ） 、斷裂能g _ f以及裂縫的尖端開口位移ctod的關系，發現卵石混凝土、碎石混凝土的荷載峰值fmax 、斷裂韌度k _ （ ic ）隨強度增加而增加，卵石混凝土的斷裂能g _ f隨強度增加而呈增加趨勢，碎石混凝土的斷裂能g _ f隨強度增加變化趨勢平直，增勢不明顯。To meet the demands for large space and flexible compartmentation of buildings, laminated vierendeel trusses are adopted in high - position transfer story structures. first the bearing characteristics are analyzed, in which reasonable stiffness ratio of the upper chord, middle chord, and lower chord is derived. then combined with an actual engineering model ( 1 8 similar ratio ), the static loading and pseudo - dynamic tests of two models for laminated vierendeel truss used in transfer story structures are conducted, in which one model adopts reinforced concrete, and the other adopts prestressed concrete and shape steel concrete. seismic behaviors are analyzed, including inter - story displacement, base shear - displacement skeleton curves, and equivalent viscosity - damping curves. a program is programmed to carry out the elasto - plastic dynamic analysis, and displacement time - history curves of the two models are derived. the test and analysis results show that the laminated vierendeel truss with prestressed concrete and shape steel concrete has excellent seismic behaviors. it can solve the disadvantages of laminated vierendeel trusses used in transfer story structures. finally, some design suggestions are put forward, which can be referenced by similar engineering
為滿足建築物大空間和靈活隔斷要求，在高位轉換層結構中採用迭層空腹桁架結構.首先分析了其受力性能，得出了空腹桁架各構件合理的截面剛度以及布局形式.然後結合一實際工程，進行了兩榀迭層空腹桁架轉換結構模型（ 1 : 8相似比）的豎向荷載下靜力試驗以及擬動力試驗.其中一榀為普通混凝土迭層空腹桁架，另一榀配置了預應力和鋼骨混凝土，對比分析了兩模型的層間位移比、骨架曲線以及等效粘質阻力系數等抗震性能的比較，並進行了彈塑性動力分析.試驗和分析結果表明，配置預應力和型鋼混凝土的迭層空腹桁架轉換結構具有良好的抗震性能，可以成功地解決迭層空腹桁架作為轉換層結構所產生的弊端問題，最後對這類轉換層結構提出了相應的設計建議According to the guidline, two nd : yag lasers have been designed and set up, one is end - pumped by lower output power ld using a selfoc micro lens, and the other is end - pumped by high output power ld using a pair of lenses are designed, and the characteristics such as output power and power stabilization of both solid - state lasers are investigated. thirdly, when an empty liquid crystal cell is inserted in the cavity of the nd : yag laser pumped by high power ld, the laser can operates in single axial mode. finally, according to the relationship between the laser output power and the longnitudinal a ld - end - pumped nd : yag laser sensor for displacement measurement has been investigated theoretically and demonstrated experimently, the results indicate that when the mean radius of pumping inside the laser cavity is far less than that of the oscilating laser mode, the exponential of the output power is a gauss function of the longitudinal positon of focused spot of ld pumping beam, both the measurement range and the sensitivity are dependent on the incident pumping power, as the incident pumping power is increased, the measurement range is enlarged and the sensitivity is improve d
本文首先介紹了ld泵浦nd ： yag激光器的發展狀況、主要特性及其應用，從四能級速率方程出發，推導了ld泵浦nd ： yag激光器的閾值、輸出功率和斜效率的表達式，並簡述了激光器的工作原理、結構型式和倍頻方法；其次，以空間相關的速率方程為基礎，提出了ld端面泵浦nd ： yag激光器的設計方法，給出了一定泵浦耦合方式下，振蕩光模尺寸、最佳輸出耦合率、泵浦光模尺寸、泵浦光焦斑位置等參數的選取依據，以此為依據，設計了自聚焦透鏡耦合小功率ld泵浦nd ： yag激光器和透鏡組耦合高功率ld泵浦nd ： yag激光器，對激光器的輸出功率和功率穩定性等特性進行了實驗研究；再次，在帶尾纖輸出的高功率ld泵浦nd ： yag激光腔內插入一隻空液晶盒，觀察到了激光器以單縱模運轉；最後，根據泵浦光焦斑端面位置對激光輸出功率的影響規律，提出了ld端面泵浦nd ： yag激光位移傳感新方法，並進行了理論和實驗研究，研究結果表明：當激光晶體內泵浦光平均光斑半徑遠小於振西安理工大學碩士學位論文蕩光束腰半徑時，激光輸出功率的自然指數與泵浦光焦斑的縱向位置成高斯變化規律，測量范圍和靈敏度依賴于泵浦功率，隨著泵浦功率的增加，測量范圍擴大，靈敏度提高，當端面泵浦功率為7 . 24w （最大輸出功率為1 . 926w ）時，激光位移傳感器的測量范圍和靈敏度分別是13 . 045mm和0 . 148mw / pm 。A general consensus exists related to the influence of slow crack propagation ahead of the crack tip upon the nonlinearity observed in the typical load - deflection response of the concrete specimen, namely, concrete exhibits somewhat quasibrittle behavior, which has been verified by the inapplicability of the conventional linear elastic fracture mechanics ( lefm ) and fracture models suitable for metal - like materials
現在已經意識到，混凝土在其典型的位移曲線中呈現出的非線性特徵是由於裂縫在端部的緩慢擴展引起的，可以認為是混凝土的一種半脆性性能。這是在發現傳統的線彈性斷裂力學（ lefm ）和適合金屬類材料的斷裂模型不適用於混凝土研究時得出的結論。The bias magnetic field of the bias coil driven by bias current and small signal test current, results in the induced signal of the control coil. the terminal voltage of the control coil is detected by the test circuit. then the signal containing the information of rotor displacement is obtained, from which we can get the dc voltage signal proportional to the rotor displacement through half - wave rectification circuit and low pass circuit. this dc signal is put into a pid controller to get the control signal of the rotor displacement
偏置測試電路向偏置線圈輸入偏置電流和小信號測試電流，兩者產生的偏置磁場在控制線圈產生感應信號，檢測電路檢測控制線圈端電壓並提取含有轉子位移信息的電壓信號，該信號經半波整流電路和低通濾波電路后得到與轉子位移成正比例的直流信號，再由pid控制器轉換為轉子位移的控制信號，最後控制信號輸入功放電路產生控制電流，實現閉環控制。Slope - deflection equation with a type of non - ideal constraints at end of beam
一類非理想桿端約束下的轉角位移方程When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved
分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。Based on the force - method equation, the stiffness matrix and fixed - end nodal displacement and force vector are derived
在力法方程的基礎上，給出了組合梁單元的剛度矩陣、桿端位移向量及桿端荷載向量並建立了剛度方程。The theme get the integration between design of the large highway bridge in anqing and theory studying, carry out an research in emulating calculation of steel box beam cable - stay bridge. the theme used the transfer - matrix in solving computing of cable - stay bridge structure, got a improving in computing of cable and the load and landed of cable strength
針對鋼箱粱斜拉橋的特性，論文確定了以控制箱粱梁端位移與拉索內力為調整目標，利用循環的正裝過程對斜拉橋的模擬進行計算，並對索塔的塔頂位移進行了良好的控制。With the development of the techniques for seismic mitigation and isolation, the fluid viscous dampers are usually equipped at the girder ends of long - span bridges in case the girder ends need to be restricted due to great amount of girder movement or the costly large expansion joints at the girder ends need to be protected
摘要隨著減隔震技術的發展，在大跨度橋梁中，當梁端位移比較大需要限制位移（或梁端設置有價格高昂的大型伸縮縫，需要保護伸縮縫）時，梁端會設置阻尼器。To restrict the displacement at stiffening girder ends under action of earthquake and to ensure that the girders will not cause too fast movement speed towards the expansion joints lest the joints should be damaged, the constraint devices are intended to provide for the girder ends of xihoumen bridge, the zhoushan mainland and islands link project
摘要為限制地震作用下加勁梁的梁端位移以及使梁體不對伸縮縫作用過大的速度以免損害伸縮縫，計劃對舟山大陸連島工程西堠門大橋設置梁端約束裝置。Then the monte carlo method is applied to simulate the random parameter, the length of the column, to acquire ensemble mean square response
用數值求解了當柱長為隨機變量時，剪切柱頂端位移均方響應的時間歷程。分享友人