等壓燃燒 的英文怎麼說

中文拼音 [děngyāránshāo]
等壓燃燒 英文
constant pressure combustion
  • 等 : Ⅰ量詞1 （等級） class; grade; rank 2 （種; 類） kind; sort; type Ⅱ形容詞（程度或數量上相同） equa...
  • 壓 : 壓構詞成分。
  • 燃 : 動詞1. （燃燒） burn 2. （引火點著） ignite; light
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 燃燒 : （物質劇烈氧化而發光、發熱; 燒） burn; kindle; flame; set on fire; [化學] combustion; inflammation; ignition
  1. Mayer a e h j, stowe r a. experimental study into mixing in a solid fuel ducted rocket combustion chamber [ r ]. aiaa 2000 - 3346

    餘勇，陳小前，等.三維實驗固體火箭沖壓發動機燃燒室湍流反應流數值模擬[ j ] .國防科技大學學報， 2002 ， （ 5 ）
  2. Abstract : in the research of internal combustion engine, recordingin - cylinder pressure and temperature is an essential technique to study the thermal cycle of internal combustion engine. the combustion analyzer developed in this study will give both the measurements at sampling points per crank angle or sampling cycle, calculate and show the real time parameters which decide the working process of internal combustion engine, such as pressure accelerating rate, indicateed mean effective pressure, cycle - to - cycle variation, heat release rate, etc. compared with the imported congeneric products, the analyzer has many advantages such as chinese interface, low price, easy operateing, convenience in maintainance and easy upgrading

    文摘:為了測錄內燃機缸內的壓力及溫度，開發了一種內燃機燃燒分析儀.該分析儀由國產高速數據採集卡及自行開發的控制軟體組成.它不僅能精確設置每度曲軸轉角內采樣點的個數和採集循環數，而且在採集過程中能實時計算和表徵內燃機工作過程的壓力升高率、平均指示壓力、循環變動率、放熱率等參數.經實際使用以及與國外產品相比表明，此分析儀具有全中文界面、價格低、操作簡單、使用維護方便、功能便於擴充等優點
  3. Long - hole and geometrical proportion type of mixing unit is finally adapted in lpg supply system, and power and torque output of lpg engine are improved by increasing compression ratio, and ignition characteristic is tried to adjusted to satisfy engine performance. meantime emission performance and noise level of lpg engine at full - throttle and other various part - throttle operations are tested and compared with former gasoline engine. ( 3 ) it is verified by engine dyno tests that lpg engine has better synthesized performance at aspects of power and torque, fuel economy, as well as emission than former gasoline engine

    選擇了等比例長孔式混合器控制空燃比；通過提高壓縮比來彌補動力性的損失；以動力性為主控目標，對最大功率點、最大扭矩點、中等轉速、最低轉速點所對應的發動機轉速做了點火特性的調節；通過空燃比的合理控制，直接改善發動機的動力性、經濟和排放指標；作為對缸內燃燒過程的理論分析，進行了燃燒特性的實驗測試；對原汽油機和新開發的液化石油氣發動機，進行了外特性和部分負荷特性以及怠速的排放及噪聲對比性測試。
  4. And the experimentation has been done. it ' s primary results were given, such as temperature and pressure curve for the combustor and gasifier

    並進行了多聯產方案試驗，給出了燃燒爐、氣化爐的升溫曲線、床層壓降曲線等初步試驗結果。
  5. Ionic liquids are extensively studied in areas of chemical synthesis, separation technology, electrochemistry and material processing due to their unique properties such as high electrical conductivity, high thermal stability, low measurable vapor pressure and incombustibility

    摘要由於離子液體具有電導率高、熱穩定性好、蒸氣壓低、不燃燒等優良性質，越來越多地應用於有機合成、分離、電化學和材料加工等領域。
  6. Energy consume, electric strength, insulation resistance, ground conductivity, leakage current, microwave leakage, power input, normal temperature, humidity treatment, glow wire, horizontal flame, vertical flame, tracking, ball pressure, rainproof, water splash, dustproof, salt fog, endurance, motor load test, cord flexing, cord pulling, pull & torque test, lamp replacement, construction check etc

    能耗、電氣強度、絕緣電阻、接地連續性、泄漏電流、微波泄漏、功率、溫升、濕熱試驗、灼熱絲、水平燃燒、垂直燃燒、漏電起痕、球壓試驗、防雨淋、防濺水、粉塵、鹽霧、耐久性（壽命）試驗、電機負載試驗、電源線彎折、電源線提拉、拉扭力測試、燈頭互換性、安全結構檢查等。
  7. Avoiding the difficulties of detecting the difficult parameters in furnace control and of building up the models, integrated with fuzzy control and conventional pid control, abb ’ s control it system is used to predict the bloom surface and center temperature directly based on the temperature of furnace wall easily to be detected so that the temperature settings in various furnace sections can be self - corrected, the furnace temperature of each section self - adjusted and on - line parameters of combustion control self - optimized. in addition, the heating parameters and the operating status of the field plant can be monitored with alarm

    採用abb公司的controlit控制系統，避開爐子控制中遇到的困難參數檢測及建模困難等因素，直接根據容易檢測的爐壁溫度來推知鋼坯表面溫度及鋼坯中心溫度，將模糊控制技術與常規pid控制相結合，實現各段溫爐設定值自修正、各段爐溫自協調、各參數在線自整定的自尋優最佳燃燒控制;對熱工參數、現場設備的運行情況進行監視、報警，實現爐膛壓力、管道壓力、換熱器的保護控制，並將重要參數送往廠級mis網路。
  8. Focusing on the performance evaluating and the design of tripropellant injector, adopting the cold test rig with background pressure supply, malvem particle analyzer, ccd photography system, tripropellant hot test - bed, numerical simulation software and auxiliary theoretical a nalysis, the d ischarge c haracteristic a s w ell a s a tomization p erformance o f the injector and the combustion performance as well as the mode - transition characteristic of thrust chamber are studied detailedly based on the 3 different structures of coaxial tripropellant injector, large numbers of important conclusions are gained

    本文圍繞三組元噴嘴的性能評定及設計方法。採用反壓冷試臺、馬爾文測粒儀、 ccd高速攝影系統、三組元發動機熱態試驗臺、數值模擬程序及輔助理論分析等多種技術手段和研究方法，對三種結構的同軸式三組元噴嘴深入進行了噴嘴流量特性和霧化特性、推力室燃燒性能和轉工況性能研究，得到了大量重要結果。
  9. Based on the analysis of the combustion in cylinder, the thorough research of multiparameters ( engine speed, load, ignition timing, injection timing, injection nozzle type, compression, ignition pattern etc. ) on methanol engine combustion cyclic variations is made on a 1130 single - cylinder diesel engine fueled with methanol

    在燃用甲醇燃料的1130單缸柴油機上，通過缸內燃燒分析，對影響甲醇發動機循環變動的各種因素（轉速、負荷、點火提前角、噴油提前角、噴油嘴類型、壓縮比、點火方式等）進行了詳細的研究。
  10. We can get many physical parameters through indicator diagram acquired in the experiment. such as indicator work, mean indicated pressure, maximal pressure and corresponding crank angle, maximal rate of pressure rise and corresponding crank angle and mass fraction burned, heat release rate, etc. these physical parameters can analyze and show primary in - cylinder combustion process in engine

    通過實測的示功圖，經過計算整理可以獲得諸如指示功、平均指示壓力、最高燃燒壓力及其對應曲軸轉角、最高壓力升高率及其對應曲軸轉角、已燃質量分數、燃燒放熱率等物理量，可供進一步分析和揭示發動機缸內燃燒過程。
  11. The performance experiments of emulsified diesel oil are done on a 1135 diesel engine. by a lot of experiment data and charts, the factors that influence the combustion effect are analyzed, including the factors of emulsified fuel self such as emulsifiers, water content, emulsifying way, and the factors of diesel engine such as fuel injection advance angel, injection pressure, load, model of engine, and so on

    在1135柴油機上進行了乳化柴油的臺架試驗，通過大量試驗數據及圖表分析了影響乳化油燃燒效果的因素，包括乳化油自身的因素如乳化劑、含水量、乳化方法等，以及發動機的狀況與參數如噴油提前角、噴油壓力、工況、機型等。
  12. Results show that all the geometric parameters have remarkable effects on combustion performance ; the swirl of intake air generated by skew intake holes enhances fuel - air mixing, minimizes dead zone and stabilizes the flame with reverse flow, but the excessive reverse flow can cause overheat in combustion chamber and exhaust ; the consistency of flow resistance in intake and exhaust system is conducive to the stability of heater performance

    研究表明，燃燒室進氣孔的孔徑、孔數、孔的分佈及方向等均對燃燒性能影響很大；斜孔所產生的旋轉進氣，雖具有強化燃氣混合、消除死區和迴流穩焰的作用，但迴流過度會使燃燒室及排溫過高；保證進排氣系統流動阻力（壓力）的一致性，有助於保證加熱器性能穩定。
  13. These initiatives include major developments of power plant flue gas desulphurization and low nox combustion system, novel monitoring systems and noise abatement of high voltage electrical substations

    完成香港一些環保及工程的先河建設。此等建設包括燃煤發電的脫硫裝置及低氧化氮燃燒系統，先進環境監測系統及變壓站消減噪音設施。
  14. Using the traits of arc adjust itself of the co _ 2 welding, adopting slow - descending feature or even feature of electrical source equipping with system that delivering the welding rod at the invariable speed, then, the arc burning steadily is realized, and the quality of welding is improved

    利用co _ 2氣體保護焊電弧的自身調節特性，採用緩降或平硬特性的電源配等速送絲系統，通過改變電源空載電壓來調節電弧電壓，再利用電弧電壓和熔化速度之間的關系調節焊絲熔化速度使之等於送絲速度，最終實現電弧的穩定燃燒。
  15. An experimental study is carried out on the effect of following factors on the combustion performance of a vehicle fuel heater : geometric parameters ( the number, diameter, distribution and direction of combustion chamber intake holes ) and intake and exhaust pressures

    摘要對車用燃油加熱器燃燒室進氣孔徑（流通面積） 、孔的分佈、孔的方向等幾何參數和進排氣壓力對加熱器燃燒性能的影響進行了試驗研究。
  16. The convective term is solved by ausm + ( a sequel to ausm which means " the advection upstream splitting method " ). the 7 species 8 steps model and 7 species 7 steps model of hydrogen / air is used in the hydrogen reacting flowfield, the 9 species 5 steps model of methane, the 10 species 10 steps model of ethane and the 10 species 13 steps model of kerosene are used in the hydrocarbon reacting flowfield, the results of the distributions of velocity, mach number, pressure, static temperature, total temperature, species mass fraction and the combustion efficiency are gained, and the numerical results of the pressure of hydrogen and methane are compared with those of the experiment

    計算中通量項採用ausm +通量分裂格式，氫反應流場採用氫/空氣的七組元八方程模型和七組元七方程模型，碳氫反應流場採用甲烷的九組元五方程模型、乙烯的十組元十方程模型和煤油的十組元十三方程模型，得出了超燃發動機燃燒室流場的速度、馬赫數、壓力、靜溫、總溫和組元質量分數分佈及燃燒效率等性能參數，其中氫和甲烷的計算壓力分佈與實驗結果進行了比較。
  17. Based on detailed analyze on turbine engine and ramjet, a new conceptive internal - rotor burnt rotating ramjet ( irbrr ) with an rotating cylinder in the center of rotor in which the revolved stream can be ram - compressed and burnt has been proposed and some primary research have been done as below : the scheme of structure, principles, thermodynamic cycle and performances of the new conceptive engine has been studied in the paper

    本文通過對燃氣渦輪發動機和航空沖壓發動機的原理結構進行詳細分析並進行融合創新，提出了一種利用內置旋轉汽缸進行旋轉氣流沖壓壓縮和旋流燃燒的新概念內置燃燒室旋轉沖壓發動機，並進行了一些前期的基礎性探索研究，具體研究內容有:對旋轉沖壓發動機進行了總體方案設計、工作原理分析、氣動熱力循環和性能分析等概念性研究。
  18. Moreover, it has been pointed out that the hydrogen engine used in ? cylinder injection with high pressure can increase volumetric efficiency and compression ratio, - therefore, the performance indexes in this engine, such as output power, thermal efficiency, range of thickness of mixture with normal operation and nox emission, can be improved, and it is possible for the engine to realize rapid combustion of thin mixture, so abnormal combustion, such as backfire, pre ? ignition, can be controlled effectively

    指出了採用內部混合氣形成方式且高壓噴射的氫發動機，有利於提高充氣效率和壓縮比，從而改善發動機的動力性和經濟性；有利於擴展發動機正常工作的濃度范圍；並且有利於實現稀薄混合氣快速燃燒，從而可以有效地抑制早燃、回火及爆燃等異常燃燒和no _ x排放量。試驗指出了發動機的點火正時、噴射正時及噴氫量對發動機的性能、異常燃燒、 no _ x排放量有很大影響。
  19. ( 3 ) application in the combustion pot based on the calculated data and experimental results, the combustion pot was designed, and its output pressure was measured

    對計算結果的分析表明，負氧平衡系數較大的hns -燃燒性能受裝填密度（壓力）等的影響較大。
  20. The main achievements are as follows : 1 it ' s for the first time to extensively investigate effects of main combustion system parameters such as plunger diameter, plunger stroke, fuel delivery advanced angle, valve opening pressure of nozzle on performance of dme engine. the parameters are optimized

    取得的主要成果有： 1系統地研究了油泵柱塞直徑和行程、供油提前角、噴嘴啟噴壓力等發動機燃燒系統主要參數對二甲醚發動機性能的影響，優化了這些參數。
分享友人
分享到 Line

分享到臉書