管式加熱爐 的英文怎麼說
中文拼音 [guǎnshìjiārèlú]
管式加熱爐
英文
cell type heater-
We specialize in manufacturing & developing the high efficiency self recuperative gas burners, which are widely used in direct heating and the radiant tube in various industrial heat treatment furnaces
本公司專業生產和開發高效率空氣自身預熱式燒嘴，廣泛應用於各種工業熱處理爐的明火或輻射管加熱Series full - auto pipe expander with drawing device and program interface is used with extruding machine. it is also used solitarily, while expanding pipes, the machine adopts translation, the action is steady and corret, it does not damage pipe materical, the machine adoptes double - infrared heating oven type, each oven is equipped with heating cire, the shaping method adopts expanding - end shaping, the size of pipe mouth is correct. on its panel, there is a transfer swith of expanding solvent type pipe socket ( straigh port ) and expanding sealloop type pipe socket ( rport ). the choice of expanding pipe type is very convenient, the technologocal adaptability is strong, its main electric control elements are all imported. the syetem charecteristics are steady and reliable
配有與主機配套的接料牽引裝置和相應的程序介面，既能與擠管主機聯線使用，又可以作單機使用；擴管時管材的移動均採用平移方式，動作平穩準確而且不易損傷管材；這種機型採用紅外線加熱方式且為雙加熱爐型，每個加熱爐都配有中心加熱爐芯；成型方式均採用擴管頭定型方式，管口成型尺寸準確；該機型在控制面板上設有擴溶劑型承介面（直口）和擴彈性密封圈型承介面（ r口）的轉換開關，擴管方式選擇十分方便，工藝適應性強；主要的電器控制元件均採用進口元件，系統性能穩定可靠。After thermodynamic calculation on several operation conditions of the furnace, cold - state flow and resistance mensuration, the combustion of the tubular - furnace hearth was changed into swirl and addition of radiate cylinder and oxygen content detection minish 1. 25 surplus air to less than 1. 15, improving the combustion condition and convection and radiate heat transfer efficacy, resuling in reducing the waste - gas temperature 45, decreasing exhaust gas loss, and saving fuel by 6 %
摘要通過對加熱爐幾種工況進行熱力計算、冷態試驗的流場分佈及阻力測定和熱態試驗的爐膛溫度場分佈及管壁溫度等參數的測定，確定將管式加熱爐爐膛內直流燃燒改為旋流場燃燒和增加輻射筒，增設煙氣含氧量分析，可以將燃燒的過剩空氣系數從1 . 35減小到1 . 15以下，極好地改善爐膛內的燃燒狀況和對流輻射傳熱效果，從而降低排煙溫度45 ，減少加熱爐排煙損失，節約了煤氣量6 %以上。Abstract : based on the analysis of influence of tubular rib construction on heat transfer area on steel blank and heat transfer space in furnace, a t - shape support system for tubular rib is presented, by which the construction of wholly overhead furnace hearth can be realized for large and medium scale continuous reheating furnaces, making furnace gases to come into full contact with steel blank, raising space utilization ratio of furnace chamber and improving heat exchange
文摘:分析了爐筋管結構形式對傳熱空間、坯料受熱面積的影響；提出採用t形支撐技術優化爐筋管，可實現大、中型連續加熱爐的全架空爐底，使爐氣與坯料表面充分接觸，提高爐膛空間利用率，可較大幅度提高爐膛熱交換。With double travelling cranes, advanced 60mm punching machine, 140mm fungus type punching machine ; domestic leading 159mma r tube rolling - mills, 159mm7 rack calibrator ; the national monopoly product micro tension - reducing diameter machinery and the producer gas generator ; 40, 60, 80, 220mm straightening machine ; 5 40 tons motoblocs ; bottom rolling type continual annealing furnace ; 14m pitch type heating furnace as well as qg1118 highly effective pipe cutter and so on as well as correlated necessary facility
公司據有雙配行車的大型廠房17500平方米，先進的60mm穿孔機， 140mm菌式穿孔機國內領先的159mmar軋管機， 159mm7機架定徑機國家專利產品微張力減徑機和煤氣發生爐40 60 80 220mm矯直機540噸拉拔機滾底式連續退火爐14m斜坡式加熱爐以及qg1118高效切管機等以及相關配套設施。Single burner gas - fired overhead radiant - tube heaters. part 1 : safety
單鍋爐燃氣的頂置散熱管式加熱器.第1部分:安全性The new device consists of paint - drying box, heat carrier boiler, heating pipe, expansion tank, gas separator and oil tank, etc. the data of two applied examples shows that heat carrier paint drying method is able to make painting - drying cost drop by 88 %, compared with the conventional one, that it has some advantages such as uniform temperature field, good appearance and lower costs, compared with conventional hot air convection mode
該裝置主要由熱載體烤漆爐、輻射加熱管，熱載體爐、膨脹器、油氣分離器和儲油槽等組成。應用實例的測試數據表明，與傳統的遠紅外電加熱鋼瓶烤漆方式相比較，鋼瓶熱載體烤漆節能和降低能耗費用十分顯著，能耗費用降幅達到88 。與熱風爐對流烤漆方式相比較，熱載體烤漆方法不僅節能，而且烤漆爐溫度場均勻穩定，同時烤漆的外觀質量也得到了明顯提高。Safety assessment of vertical furnace tube for catalytic cracking unit
催化裂化裝置立式加熱爐爐管評定The object to study in this paper is the electric heat reservoir boiler, which is used to supply heat water and bask for the resident population. the use of the system define the character of the output medium with the lower request on quality and parameter, at the same time, it ask the boiler should has the higher character on the respect of the cost, reliability, economy, and so on. hence, the paper carefully design and study the system for the choice and design of the boiler core heating componet, the lay of the heat exchanger, the working status of the heat reservoir equipment, the adjustment and control mode of to supply heat water. the study work mainly include underside some contents, forexample : 1. to confirm the heat medium parameter to adapt the requirements of the most of the heating equipments and to design the instruction of the boiler and heat reservoir as simple as possible
圍繞上述原則，本文從電熱鍋爐核心加熱元件的選型及設計、換熱面的布置、蓄熱設備的運行工況、供熱的調節方式以及控制方法進行了較細致的研究和計算，具體研究工作有以下幾個方面： 1 .根據使用要求，確定適用於多數採暖設備的熱介質參數，設計在結構型式上盡可能簡單的鍋爐和蓄熱器； 2 .對製造加熱元件電熱管的各種材料進行了對比和分析、在結構尺寸上進行了仔細的分析和計算，根據實際使用條件給出合理的設計，使其具有較高的可靠性和使用壽命； 3 .對不同換熱面布置形式進行傳熱分析。Heat pipe air pre - heater is adopted to recover gas heat to heat up cold air for burning, reducing flue gas temperature and increasing heat efficiency of injecting steam boiler
採用熱管式空氣預熱器，利用排煙熱量加熱冷空氣，降低了煙氣溫度，減少排煙熱損失，提高注汽爐熱效率。Production test of the production line is showed that anneal furnace combustion system with regenerative radiant - tube combustor compare with conventional radiant tube burner not only have superiorities on saving energy and environmental protection but also have advantages on temperature distribution and temperature control properties
生產線試生產的情況表明，退火爐燃燒系統使用蓄熱式輻射管燃燒器比使用常規輻射管燃燒器不僅在節能、環保方面具有優勢，而且在加熱均勻性和爐溫控制方面也有一定優越性。Welded edge sheathed thermocouple is used to measure surface temperature of heat furnace pipe and smoke pipeline and widely applicable for oil refining, power generation, metallurgy, chemical fibre and food etc
刀刃式鎧裝熱電偶是用於測量加熱爐管和煙道管表面溫度的儀表，廣泛應用於煉油電力冶金化纖食品等The bpvo aims at regulating the standards and operation of equipment such as boilers, pressure vessels, including thermal oil heaters, steam receivers, steam containers, air receivers and pressurised cement tanks mounted on trucks or trailers
《鍋爐及壓力容器條例》旨在對鍋爐、壓力容器等器具的標準及操作加以規管。鍋爐及壓力容器包括熱油式加熱器、蒸汽容器、蒸汽甑、空氣容器，以及貨車或拖車上的加壓水泥槽。The bpvo aims at regulating the standards and operation of equipment such as boilers, pressure vessels, including thermal oil heaters, steam receivers, steam containers, air receivers and pressurised cement tanks mounted on trucks or trailers. our work and achievements in 2002
《鍋爐及壓力容器條例》及其附屬規例旨在對鍋爐、壓力容器等器具的標準及操作加以規管；鍋爐及壓力容器包括熱油式加熱器、蒸汽容器、蒸汽甑、空氣容器，以及貨車或拖車上的加壓水泥槽。Abstract : the in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging
文摘:針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。The in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging
針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。For example, heating of the air could be a duct mounted hot water coil, duct mounted electric elements, duct mounted gas fired burner, reverse cycle air conditioning unit, room mounted panel radiator etc
例如，空氣加熱的方式有：通過熱水盤管風管送風，電加熱風管送風，燃油鍋爐取暖風管送風，製冷逆循環機組制熱，地板輻射採暖，等等。Application studing on the high temperature air combustion system in heating furnace for rolling steel
蓄熱式燃燒技術在新興鑄管一軋加熱爐上的應用實踐The thesis emphasis the way and arithmetic of the key equipment of walking reheating furnace : loader machine, unloader machine, walking system, series transfer roll, control system of burning and tracking of steel billet, . make use of the system, we can carry out the function of transferring measuring and weighting, detecting, loading and unloading tracking the steel billet, we can control process of burning and exchange data each other to track the steel billet and manage the process over all of product line. goals of reheating furnace ' s producing process such as high yield, low consuming and pollution, automatic operating mode are achieved
本文著重研究了步進式加熱爐關鍵設備如：裝鋼機、出鋼機、步進梁、爐前爐后輥道、燃燒控制、板坯物流跟蹤等控制對象的具體控制軟體流程、速度控制曲線、行程計算等具體控制策略和演算法，完成了攀鋼1450熱軋加熱爐基礎自動化系統（ l1 ）和熱工儀表的一級控制，實現板坯輸送、測量、裝出料、物流跟蹤、加熱爐燃燒控制以及板坯庫的數據信息交換，通過plc和二級計算機系統進行順序、定時、聯鎖與邏輯控制，實現了操作自動化與物料系統的全線跟蹤管理。Multi burner gas - fired overhead radiant tube heater systems for non - domestic use - part 1 : system d, safety ; german version en 777 - 1 : 1999 a1 : 2001 a2 : 2001 a3 : 2002
非家用架空式多用燃氣爐輻射管加熱器系統.第1部分: d分享友人