簡單傳動軸 的英文怎麼說

中文拼音 [jiǎndānzhuàndòngzhóu]
簡單傳動軸 英文
simple live axle
  • 簡 : Ⅰ形容詞（簡單） simple; simplified; brief Ⅱ動詞1 （使簡單; 簡化） simplify 2 [書面語] （選擇人才...
  • 傳 : 傳名詞1 （解釋經文的著作） commentaries on classics 2 （傳記） biography 3 （敘述歷史故事的作品）...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 簡單 : 1 （不復雜） simple; uncomplicated; plain; simplicity 2 （平凡 多用否定式） commonplace; ordinary...
  1. In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology

    為使二維振動傳感器在兩主軸方向的靈敏度大致相同，敏感元件採用高度對稱的四梁結構，其中每個軸向上均採用帶折疊梁的雙側叉指電容結構，採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件，具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算，並利用有限元法進行了模擬分析，根據模擬結果得出了優化參數;在確定敏感結構的基礎上，研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析，利用差動測量技術得到由振動引起的微小電容變化量，經c - v介面電路進行相位調制處理，然後通過解調輸出與加速度成正比的電壓信號。
  2. In order to solve the two problems, this paper adopts the method of reduced gradient to design precisely the parameter of friction and transmission ratio of gearbox and the gear teethes of the sixth gear of the second shaft

    本文通過對多種解決方案的分析，選擇了適當改變變速器一檔傳動比及二軸六檔齒輪齒寬這一簡單的方案使問題得到基本解決。
  3. The structure of this magnetic inducting crankshaft position sensor assembly is simple, reliable easy for installation and use, being a crucial part of electronically controlled engine. as one of the important input signal of ecu controller, the sensor assembly can transmit stable cranking signal under any rotating speed of engine and ensures the stability of the performance of electronically controlled engine in respect of oil consumption, exhaust and output

    該磁感應式曲軸位置傳感器總成結構簡單，工作可靠，安裝使用方便，是電控發動機重要關鍵的部件作為ecu控制器重要的輸入信號之一，該傳感器總成能在發動機任何轉速輸出穩定的曲軸角度信號，可確保電控發動機在油耗排放輸出功率方面的性能保持穩定。
  4. The influences of thermal effect of an axis on its design precision were discussed and the temperature distribution of a rotating axis was obtained by the conventional heat transfer equations that needed a complex solving procedure and gave a blurry distribution rule

    摘要考慮了熱對提高軸類件設計精度的影響，並通過傳統導熱微分方程法和一般傳熱學理論對主軸在運動時熱分佈進行了分析，指出了傳統熱微分方程解法復雜，從解析式中難以看出溫度分佈規律，運用傳熱學理論解法簡單明? ，結果易於反映各參數關系，精確度較高，實用性強。
  5. The elastic effect is different from the effect of rigid support, in this paper, a spindle is simplified as one - disc rotor or multi - discs rotor. by the rules of riccati transfer matrix, the varieties of dynamic properties, inherent frequency and main vibration model of the rotor are calculated

    主動磁軸承支承是彈性的，將主軸分別簡化為單圓盤轉子、多圓盤轉子等進行研究，應用傳遞矩陣法計算出在支承剛度變化時的轉子動態特性、固有頻率和振動主模態等特性的變化。
  6. Simultaneously, some rules about design and combination are established in this thesis. on the basis of the discussion on the theory and the design requirements matched with the peg - hole assembly, such as the simple structure, flexible motion, easy control and light weight, by fully analyzing model selection and trassmission method of manipulaotr, reasonable trassmission plans are constituted and a new prototype was manufactured successfully

    在對機械操作臂模塊設計理論探討的基礎上，根據軸孔裝配任務對機器人機械操作臂的設計要求，即結構簡單、運動靈活、易於控制、質量輕等，通過對機械操作臂的選型、傳動方式的具體分析，確定了合理的傳動方案，成功地研製了一臺新型類人機械操作臂樣機。
分享友人
分享到 Line

分享到臉書