粉末壓出成形 的英文怎麼說
中文拼音 [fěnmòyāchūchéngxíng]
粉末壓出成形
英文
compacting molding- 粉 : Ⅰ名詞1 （粉末） powder 2 （用澱粉製成的粉條或粉絲） noodles or vermicelli made from bean potato o...
- 末 : Ⅰ名詞1 （東西的梢;盡頭） tip; terminal; end 2 （非根本、非重要的事物） nonessentials; minor detai...
- 壓 : 壓構詞成分。
- 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
- 粉末 : powder; flour; stive; smalls
-
Microstructure of the composite layer was analyzed with help of optical microscope, scanning electronic microscope ( sem ), electronic probe microanalysis ( epma ) and x - ray diffraction ( xrd ). the compacting of the billet and the forming mechanism of the carbide reinforcement were studied based on thermodynamics and kinetics of reaction, sintering theory and the result of dta. at the same time, the wear - resistance of the composite layer was studied under condition of dry sliding friction
利用光學顯微鏡、掃描電子顯微鏡、電子探針以及x -射線衍射儀，分析了表面復合層的基體組織結構；運用反應熱力學、動力學、粉末燒結理論和燃燒合成理論，結合差熱分析結果，探討了表面復合層壓坯的燒結緻密化原理和碳化物增強相的形成機理；利用坯塊在真空燒結爐不同溫度下的燒結出來的顯微組織分析，模擬出坯塊的燒結過程中的化學反應過程。( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )
研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。
分享友人