粗滑移 的英文怎麼說

中文拼音 []
粗滑移 英文
coarse slip
  • : Ⅰ形容詞1 (長條東西直徑大的) wide (in diameter); thick 2 (長條東西兩長邊的距離寬的) wide (i...
  • : Ⅰ形容詞1 (光滑; 滑溜) slippery; smooth 2 (油滑; 狡詐) cunning; crafty; slippery Ⅱ動詞(貼著物...
  • : Ⅰ動詞1. (移動) move; remove; shift 2. (改變; 變動) change; alter Ⅱ名詞(姓氏) a surname
  1. From analysis of the test results the conclusions can be obtained as follow : the coefficient of friction under line contact is same as under point contact

    研究表明:線接觸微動摩擦因數變化與點接觸形式相同;位幅值在部分區時,表面糙度對表面磨損有影響。
  2. This product applies to the flat glass - grinding straight - edge, coarse grinding, finishing grinding, polishing once completed, tracked drive inverter used to control motor speed, smooth and reliable, cement blocks sliding box when sliding double - linear ball guide, ball screw double - action speed stability and precision

    本產品適用於磨削平板玻璃的雙直線平邊,磨、精磨、拋光一次完成,履帶驅動採用變頻電機調速控制,平穩可靠,磨頭座動箱體動時採用雙直線滾珠導軌,雙滾珠絲桿傳動,動速度穩定、精確。
  3. After description of slide line fields according to the different proportion of width / diameter, the stress function in flat plate upsetting has been determined, the changing rule of slide line fields been described, the process of column upsetting been simulated by using the software of abaqus and the theoretical value been proved through comparing the simulation value with the theoretical value

    摘要本文應用線理論來求解平板鐓模型,描述了在不同寬徑比下的線場,確立該模型單元的應力場表達式,描述其線場的變化規律,最後運用abaqus軟體對圓柱體鐓進行數值模擬,將模擬值與理論值進行對比,對理論值進行驗證。
  4. Under the careful retrospection and analysis on the previous and recent experiments about mechanical behavior of nanocrystalline metals performed by almost main investigators, the dislocation and atomic diffusion is believed to contribute hardly to the deformation of nanocrystalline alloy, and a model based on thermal activation process was applied to fit the experimental data of nanocrystalline ag

    結果表明,納米晶金屬ag的不僅具有比晶ag高2 - 6倍的拉伸和壓縮強度,而且在大范性形變階段顯示了極低的加工硬化和應變速率敏感性。結合位錯理路和非晶合金形變特徵,提出納米晶金屬ag的塑性變形主要由於晶界貢獻。
  5. When work rolls become worn the roughness is diminishing creating slippage in the roll bite at higher speeds

    工作輥磨損后,糙度遞減導致在較高軋制速度下進料(咬入帶卷)時產生
  6. ( 3 ) with the condition of table 4. 3, with increasing of temperature the average reflectance value decreases and the minimum reflectance point moves towards red direction. furthermore, temperature has little effect on the extinction coefficient ( k ). however, the refractive index value decreases remarkably when the temperature reaches about 240, but it does not change much when the temperature is below 180 and the thickness of the films increase when increasing the temperature

    ( 3 )隨著溫度的增加薄膜的平均反射率降低並且反射低谷向長波方向動;溫度對消光系數k影響不大;當溫度低於180薄膜的折射率變化不大,當溫度達到240左右時薄膜的折射率明顯降低;薄膜的厚度隨溫度的增加而增加;隨著溫度的增加tio2的晶體結構由混晶變為單一的銳鈦礦相,薄膜的表面的顆粒由多變少,表面形貌由糙多孔變得細膩平
分享友人