粗糙度測定儀 的英文怎麼說

中文拼音 [cūcāodùcèdìngyí]
粗糙度測定儀 英文
roughometer
  • 粗 : Ⅰ形容詞1 （長條東西直徑大的） wide （in diameter）; thick 2 （長條東西兩長邊的距離寬的） wide （i...
  • 糙 : 形容詞（粗糙; 不細致） rough; coarse; crude
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 儀 : 名詞1 （人的外表） appearance; bearing 2 （禮節; 儀式） ceremony; rite 3 （禮物）present; gift 4 ...
  • 粗糙 : （不精細; 不光滑; 不細致; 草率） coarse; rough; crude
  • 測定 : determine; determination; setting-out; admeasurement; assignment; assay; finding
  1. Worn surfaces of sliding pairs were characterized by scanning electron microscopy ( sem ). chemical compositons on the worn surfaces were analyzed by energy dispersion x - ray analysis ( edax ), and profiles and suface roughness of the worn surfaces were measured by stylus profilmetry

    用掃描電子顯微鏡（ sem ）對磨痕表面形貌進行了分析，用能量色散x射線分析（ edax ）對磨痕表面進行化學成分分析，並用表面輪廓儀測定了磨痕表面粗糙度和磨痕表面輪廓曲線。
  2. Preparation of steel substrates before application of paints and related products - surface roughness characteristics of blast - cleaned steel substrates - method for the calibration of iso surface profile comparators and for the determination of surface profile - stylus instrument procedure

    塗塗料和有關產品前鋼基的制備.噴丸處理鋼基體的表面粗糙度.第4部分: iso表面輪廓比較儀的校準方法和表面輪廓的測定方法.觸針儀法
  3. Preparation of steel substrates before application of paints and related products. surface roughness characteristics of blast - cleaned steel substrates. part 4 : method for the calibration of iso surface profile comparators and for the determination of surface profile. stylus instrument procedure

    塗料和有關產品使用前鋼基片的制備.噴丸處理鋼基片的表面粗糙度特性.第4部分: iso表剖面比較儀的校準方法和表剖面的測定方法.觸針儀器的程序
  4. More attentions are taken to the applications of the interferometer for the quantificational and real - time measurements in the following aspects : the laser ' s wavefront, the homogeneity of laser bar, angle deviation of flatness optical components, and surface roughness

    重點研究了數字式波面干涉儀的應用，定量、實時測量了激光波前質量、激光棒波前畸變、利用波面計算錐體棱鏡角度、表面粗糙度等。
  5. Preparation of steel substrates before application of paints and related products - surface roughness characteristics of blast - cleaned steel substrates - method for the calibration of iso surface profile comparators and for the determination of surface profile - focusing microscope procedure

    塗料和有關產品使用前的鋼基體的準備.噴丸處理的鋼基體的表面粗糙度. iso表面輪廓比較儀的校準方法和表面輪廓的測定方法
  6. Preparation of steel substrates before application of paints and related products. surface roughness characteristics of blast - cleaned steel substrates. part 3 : method for the calibration of iso surface profile comparators and for the determination of surface profile. focusing microscope procedure

    塗料和有關產品使用前鋼基片的制備.噴丸處理鋼基片的表面粗糙度特性.第3部分: iso表剖面比較儀的校準方法和表剖面的測定方法.顯微鏡的調焦程序
  7. To help answer these questions, the probe carries a surface science package ( ssp ), which will emit sound waves in the final stage of the descent to gauge the roughness of the surface

    為回答這些問題，探測器載有一套表面科學儀器組（ ssp ） ，將在降落的最終階段發出聲波，以測定表面的粗糙度。
分享友人
分享到 Line

分享到臉書