結型補償器 的英文怎麼說

中文拼音 [jiēxíngbǔchángqì]
結型補償器 英文
junction compensator
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 補 : Ⅰ動詞1 （修理; 修補） repair; mend; patch 2 （補充; 補足;填補） fill up; add supplement; supply; ...
  • 償 : 動詞1. （歸還; 抵補） repay; compensate for 2. （滿足） meet; fulfil
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 補償 : compensate; make up; make up for; make it up to sb. ; make sth. good; compensation; offset
  1. This paper introduces one novel protected clutch, which is simple in construction, good in usability, low for cost and movement expenditure, long for working life, rapid for jont or separation, compensable for all kinds of offset, and protected for overload

    摘要介紹一種結構簡單、工藝性好，造價、運行費用低廉，壽命長，可在運動中迅速接合分離，可補償兩軸之間的任何偏移，能過載安全保護的新型安全離合器的結構設計。
  2. In oilfield, feeder line of 6kv often has many branches. the pole high voltage automotive capacitor compensation system controlled by single chip computer is designed for this situation. in the system, we separate the measure position and compensation position and realize the supervision of reactive load in local area

    文章以油田6kv輸配電線路為例，針對多分支樹狀結構線路的特點，研製出由單片機系統控制的戶外術上型高壓電容器自動補償系統。
  3. Secondly, according to the character of this kind of harmonic, the solutions of power filter are deeply analyzed and an optimized topology for series connected hybrid power filter is obtained. by pwm technique, midfrequency transformer and the principle of the magnetomotive force ( mmf ) compensation, the problem to the transfer of the low - frequency harmonic power compensatory signal in the series apf is solved, in technique

    其次，針對acem系統特有的「電源諧波」特性，深入分析了濾波器方案，得到了一種適用於acem系統諧波抑制的串聯混合型有源電力濾波器優化拓撲結構，並採用了pwm調制技術、中頻注入變壓器和磁勢補償原理有效地解決了串聯apf中低頻諧波功率補償信號傳輸的難題。
  4. This article imtroduces adesign for a new style nonelastic element flexible c ouple r with good combinedcompensntion functions of axial, radial and anguladirection s. it s a mew idea designwith a simple and reasonable construction, lowpri ce and convenient maintenance. also it hasa super axial compensating ability compared with common couplers. the theory is that therotary force can be changed into lev eladvanced force. it has been proved that this couplerhas a good combined techn ique proprety and a higher rate between quality and price. itmust have cheerful prospects of application

    設計了一種具有良好的軸向、徑向及角向綜合補償功能的新型無彈性元件撓性聯軸器.這種聯軸器構思新穎，結構簡單，容易加工製造，便於裝拆維修，具有一般聯軸器所不能實現的軸向超大補償能力.設計原理可引伸拓寬到將轉動動力轉變為直線推進動力的設計上.實踐證明，該聯軸器具有良好的綜合技術性能和較高的性能價格比，極具應用前景
  5. This text divides into five chapters altogether : chapter one in the introduction, have introduced the common sensor of displacement, has pointed out the fine characteristic of hall ' s sensor, put forward the basic task ; chapter two have introduced the basic operation principle of hall ' s component ; chapter three introduce hall temperature performance, electromagnetic characteristic, zero error, frequency characteristic and these parameter commonly used compensation method and hall simple application of component ; chapter four having recommended the measurement principle of the feedback servo mechanism, systematic implementation method, the experimental result has appeared, structure the mathematics model, and has analysed the error ; chapter five have pointed out the developing direction in the future while looking forward to

    本文共分為五章：第一章緒論中，介紹了常見的位移傳感器，指出了霍爾傳感器的優良特性，提出了基本任務；第二章介紹了霍爾元件的基本工作原理；第三章介紹了霍爾元件的溫度性能、電磁特性、零位誤差、頻率特性以及這些參數常用的補償方法和霍爾元件的簡單應用；第四章介紹了反饋隨動機構的測量原理，系統的實現方法，給出了實驗結果，構建了數學模型，並對誤差進行了分析；第五章展望中指出了今後的發展方向。
  6. The principle and the mechanical structure of the air - gap inductance - type transducer are analyzed in this article, and the static parameters are calibrated. dynamic calibration is applied to air - gap inductance - type transducer which is not good in dynamic capability, to obtain the dynamic parameters of the transducer and its measuring circuit. based on the result of the dynamic calibration, the transducer and its serving circuit are modeled so that the method of how to improve the dynamic performance can be found

    本文對現有氣隙式電感傳感器在原理和機械結構上作了深入的分析，對其參數進行了靜態標定；並且針對常規電感傳感器動態響應低，不宜用於快速動態測量的缺點，引入測試系統動力學的思想，設計了一套動態校準系統，對現有傳感器進行多次動態校準，根據動態校準的實驗結果對現有傳感器建立數學模型，得到現有傳感器的動態特性；在此基礎上，根據磨床工件在線檢測的要求，設計一個硬體補償系統來提高整個測試系統的動態特性。
  7. After establishing induction motor simulation model with iron loss, this paper has investigated effect of iron loss and proposed two schemes to compensate estimated error due to iron : one modified the structure of controller, the other modified the structure of observer, both schemes eliminated the detuning effect of iron

    對于鐵耗的影響，本文建立了考慮鐵耗的感應電機模擬模型后，研究了鐵耗造成的估計誤差，並利用兩種方法對誤差進行補償，一種是修改控制器結構的方法，另一種是修改觀測器結構的方法，最終都較好地消除鐵耗對速度估計的影響。
  8. In chapter 2, author points out firstly that the elastic deformation of elastic units of a robot ' s wrist force sensor will be enlarged by the end - effector, the instruments and the work pieces, so the elastic deformation of the sensor will influence the location accuracy or kinetic accuracy of end point of a robot, under the condition of that the robot technology facing the developing of heavy load, light mass and high accuracy. it is discussed respectively that the relationship between the differential kinemics in the sensor ' s coordinate and the location accuracy or kinetic accuracy of the end point. error matrixes of location and kinemics of the end point are presented respectively based on the differential kinemics in the sensor ' s coordinate, and the on - line error compensation methods are introduced subsequently

    第二章首先指出機器人腕力傳感器彈性體的彈性變形經過機器人末端連桿、工具、工件等的放大后，會對機器人末端精確定位和運動產生的影響；然後分別研究了傳感器坐標系內的微分運動與機器人末端工件精確定位、運動的關系；在此基礎上，研究了基於腕力傳感器彈性體微分運動的機器人末端定位、運動誤差的誤差矩陣及其在線誤差補償方法；基於機器人動力學的機器人末端定位、運動誤差的誤差矩陣及其在線誤差補償方法；最後，以puma型機器人為對象，給出了基於腕力傳感器內微分運動的機器人末端定位、運動誤差及其在線補償方法的模擬實例：給出了基於機器人動力學的機器人末端定位、運動誤差及其在線補償方法的模擬實例；模擬結果表明， 1 ）基於腕力傳感器的機器人末端定位誤差在腕力傳感器允許的載荷下可達十分之幾毫米級。
  9. The spectral and group delay characteristics are studied and the potential uses of this type of grating for wavelength selection and dispersion compensation are discussed. a novel scheme of oadm configuration based on linearly chirped moir fiber gratings is proposed. we have designed a lcmfg to compensate dispersions for eight channels at the same time

    在此基礎上，提出了一種新型的基於線性啁啾moir光纖光柵的光分插復用器（ oadm ）的結構設計方案；並設計出一種中心波長、相鄰中心波長間隔都符合itu規定的dwdm波長標準的基於線性啁啾moir光纖光柵的多通道色散補償器件。
  10. The second chapter simply introduces the development of alternate asynchronous inverter technology and retrospects some types of energy - saving systems for hydraulic elevators. then the working principles of the project are discussed and analyzed at four different working status, i. e. light load upwards, heavy load upwards, light load downwards and heavy load downwards. and the chapter focus on the introduction of structure design of pump station, calculation and type selection of pump / motor reversible units, research on oil leakage principles of accumulator circuit, design of accumulator - pump / motor pressure - energy transformer and integrated valve blocks, etc. the last but not the least, the electrical wiring of vector inverter control cabin and design of computer control and data acquisition system are introduced

    論文第二章首先簡單介紹了交流異步電動機變頻調速技術的發展概況，在回顧電梯液壓控制系統節能技術的基礎上，介紹了本課題研製的「採用蓄能器的液壓電梯變頻節能控制系統研究」的基本原理，分析了動力系統在電梯轎廂輕載上下行、重載上下行等四種典型工況下的基本工作狀態和工作方式；詳細地介紹了本課題節能系統液壓動力泵站的結構設計和參數設計，重點研究了液壓動力泵站的結構設計、液壓泵馬達可逆性問題及其選型設計計算、蓄能器迴路泄漏油損失機理的研究及其補償裝置的設計、蓄能器-泵馬達壓力能量轉換裝置的設計、多功能集成控制閥組的設計等內容；最後簡單介紹了本課題矢量控制變頻控制櫃的外部附件電氣接線、計算機控制及數據採集系統的硬體設計等內容。
  11. In order to accurately analyze the error in the non - orthogonal coordinate measuring system, the circular cylindrical coordinate measuring system is discussed first and the formula of its number of errors is computed, and then it extends to the non - orthogonal coordinate measuring system of n dimensions arms of robots, and build its error compensation modal, which is proved to have high precision

    為了正確分析非正交坐標系機械繫統的誤差情況，本文先以柱坐標系測量系統為例。分析了引起測量系統示值誤差的各種機構誤差。並且分析得出其誤差項數的計算公式，然後推廣到n維機器人手臂結構的非正交坐標系機械繫統，建立其誤差補償的數學模型。
  12. In the simulation work, one 1. 5kw and one 18kw induction motors ? control system were simulated and two simplified control scheme were proposed. when developing the program in tms320f240 dsp, this paper solved two practical problems : the finite - length effect and dc bias effect. finally, sensorless control system based on adaptive filter theory are tested on the platform of 1. 5kw induction motor, the results show that the scheme ? performance is good

    在模擬過程中，針對1 . 5kw和18kw異步電機進行了模擬，並在此基礎上提出兩種簡化控制方式；在tms320f240的具體編程過程中，分別對自適應濾波器的有限字長效應、直流偏置效應等非理想因素進行了修正和補償；最後，在1 . 5kw微型異步電機上進行了轉矩閉環無速度傳感器實驗，實驗結果表明了演算法完全可以達到預期的目標。
  13. Thesis this in existing electric capacity, whether it utilize by the ct one mainly reject and mix by suitable partial pressure not low - voltage partial pressure arm not high - handed of cvt electric capacity not insulating, in the middle of and ca n ' t compensate reactor, etc. of voltage transformer, design by sectional mutual inductor that ct combine cvt with, sectional mutual inductance utensil this have electric current mutual inductor and voltage double function of mutual inductor

    本論文在現有電容型絕緣電流互感器和電容式電壓互感器製造技術的基礎上，利用ct的主絕緣電容屏作為cvt的高壓分壓臂，配以合適的低壓分壓器、中間變壓器以及補償電抗器等，設計了由ct和cvt相結合的組合式互感器，該組合式互感器具有電流互感器和電壓互感器的雙重功能。
  14. It analyses the causes to bright image movement, studies principle to compensate image movement, conforms project to compensate image movement, and designs framework to compensate image movement in the article ; to analyze and design configuration of the scanning mirror, to select matters of mirror and its support structures on the principle of consistent line expansion coefficient ; to ascertain type of moment electromotor by most rotating angle speed and most rotating moment which are required by loads in the period to take pictures, as well as by figuration size of electromotor ; to design retarder according as the electromotor parameters ; to design and optimize lightweighted mirror shapes, because the mirror is key part ; to design flexure support structure, to analyze static and dynamic characteristics of the support structure by name of patran program for validating desig n rationality ; to study function of the scanning mirror electric control system ; to test precision of the system, the results indicate the rationality of design of the scanning mirror system

    本文通過分析像移產生原因、研究像移補償原理，確定像移補償方案，並根據像移補償原理設計補償機構；分析與設計掃描反射鏡系統結構，根據材料線膨脹系數一致原則，選擇反射鏡及其背部支撐的材料；由掃描反射鏡在擺掃周期內的最大擺掃角速度確定力矩電機的額定轉速，根據負載力矩確定電機的額定轉距，綜合電機外型尺寸等因素，確定執行元件? ?電機的型號；根據所選電機的參數指標，設計1 ： 6速比的減速器；利用patran軟體對掃描反射鏡系統中的關鍵件? ?反射鏡進行輕量化設計與優化；設計反射鏡柔性支撐結構，並通過軟體分析支撐結構的力學特性，驗證反射鏡柔性支撐結構設計的合理性；從原理上研究掃描反射鏡控制系統功能；進行系統精度測試，測試結果表明掃描反射鏡系統設計的合理性。
  15. The whole article consists of 6 parts : 1. object of the project and the development background of the relative technique are introduced. 2. the theory of the micro inertial heave height measurement is depicted. 3. arithmetic model base on matlab / simulink for micro inertial heave height measurement is offered, including the result analysis for the simulation. 4. the whole hardware design base on aduc841 single chip of the mimu data collection system is depicted. 5. software design is introduced. 6. adjusting and error compensation model of the mems is depicted. at last, sum - up, view and enhancement of the system are given

    本論文分成六個部分:第一部分介紹了課題研究的目的及相關技術的發展概況;第二部分主要論述微慣性測高的理論基礎;第三部分給出微慣性測高演算法的matlab模擬模型及模擬結果分析;第四部分給出基於微慣性傳感器及aduc841單片機的微慣性數據採集系統的硬體設計及調試方案;第五部分為微慣性數據採集系統的軟體設計;第六部分介紹了微慣性傳感器的標定及誤差補償方法。
  16. The design methods of variable structure control of skeleton type are obtain ed by introducing sliding mode compensator

    通過引入滑動模態補償器，得到了簡約型變結構控制的設計方法。
  17. In this paper, the control system of industrial boiler widely used in industrial production was studied. aiming at the nonlinear object of industrial boiler with instability parameter and difficult building math model, combining fuzzy control theory and neural networks theory, a adaptive controller built with compensatory fuzzy neural networks to control industrial boiler is proposed

    本文對于目前在工業生產中廣泛應用的工業鍋爐的控制系統進行了研究，針對工業鍋爐這種具有非線性、參數不穩定、難以建立精確的數學模型的控制對象，結合模糊控制理論和人工神經元網路理論，提出用補償模糊神經網路構造自適應控制器實現對工業鍋爐的過程式控制制。
  18. The proposed control system includes the attitude controller acting on the rigid hub, designed by using pulse - width pulse - frequency ( pwpf ) modulation integrated with command shaping technique based on csvs method, and the piezoelectric material elements as sensors / actuators bonded on the surface of the beam appendages, designed by the optimal positive position feedback ( oppf ) control technique, in which the selection of ppf gains is determined via introducing a cost function to be minimized by feedback gains which are subject to the stability criterion at the

    設計的控制器僅利用輸出信息，從而避免設計撓性模態狀態觀測器以及引入狀態觀測器誤差;在此基礎上，採用分力合成方法設計命令成形控制器來抑制撓性附件的振動，設計的優化命令成形控制信號在理論上可以對系統的各階撓性模態完全抑制。但考慮到模型不確定性和外部擾動，在內迴路又設計了最優正位置反饋（ oppf ）補償器以增加撓性結構的阻尼，使撓性結構的振動能夠很快衰減。
  19. The results show that these reflective phase compensators own some advantages of high - reflectivity, continuous tunable phase compensation etc

    分析結果表明，這些反射型相位補償器都具有反射率極高、相位補償連續可調等優點。
  20. In comparison with previous results, the dynamic compensator can satisfy a wider class of uncertainties

    與先前有關結果比較，該動態補償器能適應更廣類型的不確定性。
分享友人
分享到 Line

分享到臉書