結晶器 的英文怎麼說

中文拼音 [jiējīngqì]
結晶器 英文
casting mold
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 晶 : Ⅰ形容詞（光亮） brilliant; glittering Ⅱ名詞1. （水晶） quartz; （rock） crystal 2. （晶體） any crystalline substance
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 結晶 : 1 （析出晶體） crystallize2 （晶體） crystal 3 （成果） crystallization; fruit; product; quintess...
  1. The low - melting - point sn - pb - bi alloy was used as simulacrum to investigate the distortion of meniscus

    結果表明：當電源輸入頻率增大時，結晶器內的磁感應強度減小。
  2. The control system of mould level is crucial to improve the slab quality in the continuous casting process, pid controller is used in the traditional mould level control, and it has some defaults, such as : at the start - up or finishing period of casting or during the changeover of tundish, pid control has a bad effect, its overshoot is large and its transient time is long ; the erosion of the tundish stopper and the submersed nozzles lead to the accuracy of control become bad ; the abrupt falloff of block in the submersed nozzles makes the level acutely fluctuate, and pid control can not overcome the disturbances resulted from the change of casting speed

    結晶器液位控制系統是提高連鑄產品質量的關鍵環節，傳統的連鑄機液位控制方法採用常規的pid控制，存在如下不足：開始、結束澆注和換中間罐澆注時，控制效果差，超調量大，過渡時間長；塞棒頭和浸入式水口被腐蝕后引起控制精度差；浸入式水口堵塞物的突然脫落所引起的液位劇烈波動；無法克服拉速波動引起的擾動。
  3. Molten steel level in mould of continuous cast process and casting speed can directly effect temperature of molten steel in mould

    摘要結晶器液位和鑄坯拉速可直接影響結晶器內鋼液溫度。
  4. 5. glide windows multi - way spc is applied hi the model of batch cooling crystallizer, and it works well. finally, the whole thesis is summarized, and some future research areas are highlighted

    以間歇生產過程冷凝結晶器的模擬程序為應用背景，應用滑動窗口多向主元分析方法進行統計過程式控制制，說明該方法在間歇過程的監控和診斷中的作用和特點。
  5. The distribution of magnetic induction in rectangular soft - contact mold during electromagnetic continuous casting ( emcc ) was investigated considering the electric frequency

    摘要研究了在電磁軟接觸連鑄過程中，電源輸入頻率的變化對矩形電磁軟接觸結晶器內的磁感應強度分佈規律和彎月面變化情況的影響。
  6. The moderate supersonic carbon added to the mold flux for ultra - low carbon steel is used to stay the melting speed as skeleton. then the mold flux coils have the good adiabatic, insulation and even flow property. at the same time it cause the carbon increase in the steel slabs and the operation of the ultra - low carbon is affected at last

    超低碳鋼連鑄結晶器用保護渣中，外加中超碳黑作為骨架降低熔化速度，使保護渣具有良好的絕熱保溫性、均勻流動的潤滑性，但同時卻會引起鋼鑄坯的碳增量，最終影響超低碳鋼的成功操作。
  7. The online measurement of mold heat flux can not be replaced by online temperature measurement, the later can respond the uniformity of heat transfer and thickness of solidified shell mote accurately and directly, and online temperature and heat flux measurement of mold can be used to foresee the mold conditions such as fix and scaling of mold

    溫度的在線檢測不能代替熱流的在線檢測，後者可更準確和直接地反映結晶器傳熱和坯殼厚度的均勻性；同時在線檢測結晶器的溫度和熱流有可能對結晶器的設備狀態（如結晶器的安裝狀況和水垢狀況）實現在線預測。
  8. Abstract : guiding accuracy of casting mould depends on structure and oscillation parameters, such as elastic deformation of guiding leaf - springs, play of bearings between linkages, stroke and frequency of mould oscillation, etc. in this paper, these factors are studied by means of kinetic and dynamic analysis of oscillating mechanism

    文摘:通過對連鑄機結晶器振動機構的運動學和動力學分析，研究了導向板彈簧的彈性變形、連桿軸承間隙等結構參數及振幅、振動頻率等運動參數對結晶器仿弧誤差的影響。
  9. System - design of mobile multidimensional coordinate measuring machine for inside - size measuring of i - steel crystallization device

    可移動多維坐標結晶器內腔尺寸自動測量機的系統設計
  10. Modeling and dynamic simulation for mould crystallizer oscillation based on adams

    結晶器振動裝置的模擬與研究
  11. Design of the virtual assembly of the vibration mechanism of continuous casting mold based on autodesk inventor

    連鑄機結晶器振動裝置的虛擬裝配設計
  12. Some facilities and processed are adopted during this modification, such as continuous taper control mould, leaf - spring guide vibrator, withdrawal se straightening machine and automatic torch cutter

    改造中採用了連續錐度結晶器、板簧導向振動裝置、連續矯直拉矯機、自動火焰切割機等設備與技術措施。
  13. Compared with traditional mold oscillation device, this system can conveniently change oscillation wave and alter on - line oscillatory frequency and magnitude according to the continuous casting technological requirements

    與傳統的結晶器振動裝置相比，該系統能夠根據連鑄工藝要求方便的選擇波形，並在線改變振動頻率和幅值。
  14. Oscillator mechanism with four - eccentric axes is widely used in modem continuous casting machine. with the increase of operation speeds of the machine, elastic vibrations of the machine parts became much obviously. in order to design the machine reasonably, the complex dynamic property of the system must be studied deeply

    結晶器四偏心式振動機構是大型連鑄機上廣泛採用的一種振動裝置，隨著拉速的提高，其彈性振動效應非常明顯，對其復雜彈性動力學性能進行深入研究是合理設計該系統的基礎。
  15. Numerical simulation on fluid field in mould for slab concasting

    板坯連鑄結晶器鋼液流場的數學模擬
  16. Finite element analysis of the flow field in the mould of slab conticaster

    板坯連鑄機結晶器內流場的有限元分析
  17. A study of water model on slag entrapment of molten steel in mould of slab continuous caster

    板坯連鑄機結晶器鋼液卷渣的水模型研究
  18. The effect of different operation parameters on the molten steel flow in the mould in no. 2 steelmaking plant, wisco has been studied via the three - dimensional flow field software developed by the authors

    利用開發的三維流場計算軟體，研究了操作參數對武鋼二煉鋼板坯連鑄機結晶器內鋼液流動的影響。
  19. Qualified molten steel from the steelmaking furnace will be contained in ladle and conveyed to continuous caster, poured into crastyllizer through pouring basket, then handled with the processes of vibration, water spraying cooling, straightening, roll conveying, flame cutting, and cooling on cooling bed, finally the formed billets will be stored at the stockyard or directly sent to the heating furnace of rolling mill for heating

    煉鋼爐冶煉出合格的鋼水，用鋼水包送至連鑄機，經中間包澆注到結晶器，再經振動水噴淋冷卻拉矯輥道輸送火焰切割冷床冷卻，最後存放于鋼坯堆放區或直接送至軋鋼機加熱爐進行加熱。
  20. The company changchun jichai crystallizer manufacturing plant deals in crystallizers and also in crystallisers

    為您提供關于結晶設備、晶化設備和結晶劑、結晶器的信息。
分享友人
分享到 Line

分享到臉書