結構薄度 的英文怎麼說

中文拼音 [jiēgòubódù]
結構薄度 英文
structural thinness
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 薄 : 名詞[方言] （浮萍） duckweed
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 結構 : 1 （各組成部分的搭配形式） structure; composition; construction; formation; constitution; fabric;...
  1. A thin epitaxial layer ( 10gm ) ldmos device used n - burry layer structure was proposed in the paper during the high - voltage device design, which is helpful to improve the drive circu it ? technology

    在高壓器件研究中，提出了一種外延層厚度為10 m採用n埋層結構薄外延高壓ldmos器件，對進一步改進驅動電路的工藝有著積極的意義。
  2. Analyzing and experimentally verifying the strain transducing characteristics of strain sensor. experiments tell that strain sensor capsulated by thin sheet metal can effectively transduce strain under certain mechanical robust with strain transducing efficiency of 97. 8 %, sensitivity of 83. 34 / kg, precision of 1. 64

    實驗結構證明，用薄金屬片封裝的應變傳感器在保證一定機械強度的基礎上實現了應變的有效傳遞，應變傳遞效率可達97 . 8 % ，應變靈敏度為83 . 34 / kg ，精度為1 . 64 。
  3. The desensitized explosive petn film was prepared by physical vapour deposition ( pvd ) technology, and sem was used to analyze the microstructure and grain size of petn film

    摘要採用物理氣相沉積（ pvd ）技術研製了鈍化太安炸藥薄膜，對薄膜的微觀結構和顆粒粒度進行了分析，對顆粒粒度與薄膜爆轟波穩定傳播臨界尺寸的關系進行了探索。
  4. Through the experimental research, we think : the technological capacity of fiberglass asphalt macadam if weaker than asphalt macadam, however, if use elasticized capacity to solve blending technological problem. adjust the breed of fiber silk, extend its diameter, its paving capacity is still worth exploring, asphalt - rubber macadam structure lager have good deformed - become capacity and crazed - resistance capacity, small gap rate. good water - resistance capacity, good hot - stability and simple construction technology. therefore. pitch rubber spall is a good cover material which is suitable for the second class or lower whose asphalt pavement has split open because of fatigue. and is the good structural measure of preventing half - rigidity grass - roots unit shrink - rift reflecting. pave a thin layer of pitch rubber spall between asphalt - type pavement layer and half - rigidity basic level, although the cost of building is higher than paving togongbu in the middle, the construction technology, crazing - resistance and water - resistance are better than togongbu, not only could reduce greatly the reflex of half - rigidity grass - roots unit material, long then the use lifespan of pavement, but also it is possible to reduce suitably the thickness of asphalt mixture layer, though the cast of building in the early days becomes more, in the long - term opinion, it have fully important technological and economical significance

    通過試驗研究認為：玻璃纖維瀝青碎石的技術性能不如瀝青碎石好，但路用彈性性能較好，如能解決拌和工藝問題，調整纖維絲的品種，增大其直徑，其路用性能仍值得探討，瀝青橡膠碎石結構層具有變形性能和抗裂性能良好，空隙率小，防水性能好，熱穩定性較好，施工工藝簡單的特點，因此，瀝青橡膠碎石是二級及二級以下公路因疲勞而開裂的瀝青路面的良好罩面材料，也是防止半剛性基層收縮裂縫反射的良好結構措施，在瀝青類路面面層和半剛性基層之間夾鋪瀝青橡膠碎石薄層，雖然造價比夾鋪土工布高，但其施工工藝，抗裂性能和防水性能均優于土工布，不僅可以大大減少半剛性基層材料的反射裂縫，延長路面使用壽命，而且可能適當減薄瀝青混合料面層的厚度，雖然初期造價有所增加，從長遠來看，具有十分重要的技術和經濟意義。
  5. By introduction of two lif layers, the adjustment of the position of thin layer alq3 in the microcavity is achieved and the effect of the coupling strength between the emissive dipole and vacuum electric - field on the emission intensity in ( / 2 - length microcavity is studied for the first time

    在帶有dbr結構的高q值微腔中，觀察熒光壽命變短輻射速率提高的現象。通過使用填充層，來實現對薄層alq在腔中位置的調節，研究了輻射偶極子同光電磁場的耦合強度對輻射強度的影響。
  6. But it is inadvisable to adopt too high substrate temperature. so to control the substrate temperature in an appropriate range is very important

    但是過高的基片溫度對薄膜的結構和性能都不利，所以控制溫度在一定的范圍內非常重要。
  7. The restriction factors are lack of government and policy support, the small production scale, the low degree of farmer ' s organization, the construction of industrialization management scheme was weak, internal mechanism was needed to be improved, the proportion of breed was inconsequence, low utilization ratio of resource, low research level, behindhand production technique, low science and technology content of produce, trade was lack of self - discipline, competition without orders, low level of marketing and currency, the market system was not healthiness, the scales of leading enterprises were small, so they were short of ability of bringing along others

    當前制約菏澤市牡丹產業發展的主要因素是政府行為不規范、支持力度不夠;生產規模普遍較小，農民組織化程度低，產業化經營組織建設還很薄弱，內部機制有待完善;牡丹品種結構不合理，資源利用率低;科研水平低，生產技術落後，產品科技含量低;行業自律性差，無序競爭嚴重;產品營銷、流通水平低，市場體系不健全;龍頭企業弱小，帶動能力不強。
  8. Moke and fmr studies were performed on epitaxial single crystalline fe ph. d thesis ; investigations of magnetic properties on magnetic thin, ultrathin and patterned films ultathin films on iii - v semiconductor inas substrate with thickness of 8 - 25monolayer ( ml ). the major findings are listed below : ( 1 ) the in - plane magnetic crystalline anisotropy of film with 8 - 25 ml thick are four - fold anisotropy, and the in - plane unixial anisotropy of fe / inas films decreses faster with thickness than that in fe / gaas films. it could be explained that the stain relaxation of fe / inas films is also faster than that in fe / gaas films as indicated by leed

    對于外延生長在inas襯底上、厚度為8 - 25ml的超薄fe單晶膜進行了鐵磁共振和磁光研究，獲得以下幾點結果： （ 1 ）膜厚在8 - 25ml之間時，薄膜面內的磁晶各向異性為四度對稱各向異性，垂直單軸各向異性比同厚度的fe gaas系統小許多，而立方各向異性則比fe gaas系統更接近bcc結構的fe 。
  9. In this thesis, mainly by fmr, combined with moke and magnetic measurement, systematical studies have been made on the magnetic properties, especially magnetic anisotropy in epitaxial single crystalline fe ultathin films on gaas and inas substrates in polycrystalline thin films and in polycrystalline nife and nifeco patterned films of micron and submicron rectangular elements arrays

    本論文以鐵磁共振為主要研究手段，輔助以磁性和磁光測量，對外延于gaas及inas上的不同厚度的單晶fe超薄膜、不同厚度的nife多晶薄膜和電子束光刻的多晶nife和nifeco單層利三明治結構的微米及亞微米矩形單元陣列圖形薄膜的磁性，特別是磁各向異性進行了較為系統的研究。
  10. Moke and fmr studies were performed on single crystalline fe ultathin films epitaxially grown on iii - v semiconductor gaas substrate with thickness 4. 1 - 33 monolayer ( ml ). a theoretical mode for fitting fmr experimental data was established. the results demonstrated the structures and reproduced the evolution of the magnetic properties of ultrathin films with various thickness from the state of superparamagnetic nano - cluster through coexistence of two magnetic phases to continuous film, especially the change of magnetic crystalline anisotropy from unixial to cubic

    1 - 33原子層厚度（ monolayer ，簡稱ml ）的fe單晶超薄膜進行了鐵磁共振（ fmr ）和磁光研究，建立了理論模型對鐵磁共振實驗結果進行了模擬，重現了不同厚度的超薄膜，從納米團簇到兩相共存的過度階段直至連續薄膜結構與磁性的變化，特別是磁各向異性從單軸各向異性向立方各向異性轉變的演化過程。
  11. It was concluded that, the structure of ito thin films were influenced by many working parameters such as substrate temperature, oxygenous pressure and substrate and so on. it was indicated by sem spectra of zno thin films that the surface of the sample was leveled off, and the crystals were felsitic

    結果表明，對于ito薄膜，薄膜的光電性能薄膜結構的擇優取向性和與襯底溫度、濺射氧氣壓等工藝參數有很大關系， ito薄膜的sem表明，樣品表面較平整，且晶粒也比較緻密。
  12. A particular ir feature ( primarily denoted as fano - like spectral feature ) has been observed for the first time, when co is adsorbed on island films of particular structure

    本論文首次觀察到特定納米結構薄膜（厚度大於13nm ，島狀結構）材料的fano類型光譜特徵（ fano - likespectralfeature ） 。
  13. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
  14. Abstract : based on the ahievement of epitaxial growth in several perovskite oxide films, we discuss the importance of substrate temperature ( ts ) and substrate material in the epitaxial growth of perovskite oxide thin films. influences of ts on growth orientation and epitaxial threshold temperature were observed. the results indicate that during the growth of the oxide films the phase formation and growth dynamics should be taken into consideration. the threshold temperature for epitaxial growth depends on the substrate materials. this demonstrates the influence of substrate material on the initial nucleation and epitaxial growth

    文摘:在成功地外延生長超導、鐵電、鐵磁等多種性質的鈣鈦礦結構氧化物薄膜的基礎上，討論影響氧化物薄膜外延生長的一些因素.考慮到相形成和薄膜生長動力學，在利用脈沖激光淀積法外延生長氧化物薄膜中襯底溫度是十分重要的工藝參數.襯底溫度對成相和生長薄膜的取向都有影響.考慮到薄膜是首先在襯底表面成核、成相併生長.因此襯底材料晶格的影響是不容忽視的.觀察到襯底材料對薄膜外延生長溫度的影響.在適當的工藝條件下，利用低溫三步法工藝制備得到有很強織構的外延薄膜.這突出表明界面層的相互作用對鈣鈦礦結構薄膜的取向有著相當大的影響
  15. In the formula, our experience in structural strength design and the experimental results are considered. and such factors are also considered as differences in materials of the skin and the reinforcer, effects of bending, torsion, stretching and offcenter of the reinforcer. furthermore, through post - buckling stress analysis of the skin, it is shown that even low stress level will result in buckling of the skin, but the skin still has loading capacity

    在總結過去結構強度設計和試驗分析的基礎上，應用扁殼理論，在廣義力與廣義應變關系中考慮了蒙皮與加筋不同材料以及加筋的彎曲、扭轉、伸縮和偏心等的影響，推導出適合於工程應用的加筋殼結構軸壓屈曲臨界載荷的計算方法;並通過對薄壁結構蒙皮后屈曲應力分析，說明蒙皮在很低的應力水平時就出現失穩現象，但失穩后的蒙皮仍具有一定的承載能力。
  16. But setting of strengthened floor will result in the sudden variation of structural stiffness and internal force, and will come into being weal story. the yield mechanism will difficultly " story column, weak beam " and " strong in resistance of shear force, weak in resistance of bending moment "

    在風荷載作用下，設置加強層是一種減少結構水平位移的有效方法；但在地震作用下，加強層的設置將會引起結構剛度、內力突變，並易形成薄弱層，結構的損壞機理難以呈現「強柱弱梁」和「強剪弱彎」的延性屈服機制。
  17. With these comprehensive study, the fragile region of construction strength, the reason of serious vibration and the weak element of fatigue strength are obtained, and relative improving treatments are given

    通過對該泵車的綜合分析，得到該泵車結構強度薄弱環節、產生較大振動的原因及疲勞強度薄弱部位，並提出相應的改進措施。
  18. Abstract : a new method of machining tube parts was put forward and local upsetting tube parts can be manufactured by this method. it is important to raise mechanical strength, improve the quality and reduce production costs

    文摘:提出一種新的加工薄壁管類件的方法，利用該方法可以加工局部變粗的各種形狀的管類件，這對于提高工件的結構強度、材料的利用率和降低工件的重量及製造成本具有重要的意義。
  19. The stiffness of weak - layer frame structures is not uniform in vertical direction, and there will be severe layer - deformation in weak layer when earthquake occurs

    具有薄弱層的框架結構剛度沿豎分佈不均勻。在地震中薄弱層將產生較大的層間變形，從而發生嚴重的震害。
  20. When thf sputtering temperature is low, the films have the patterns of typical amorphous structure. al can only exists in the films by the form of al clusters and si can only exists in the films by the form of si or siox ( x < 2 ). the properties of photoluminescence ( pl ) and ple from the films have been studied

    當薄膜沉積的基片溫度較低時，薄膜呈現非晶結構，薄膜中的鋁主要是以單質鋁的團簇形式存在於非晶的sio _ x （ x 2 ）中，而多餘的硅則以單質或低價氧化物的形式存在於膜中。
分享友人
分享到 Line

分享到臉書