絕對冷卻 的英文怎麼說

中文拼音 [juéduìlěngquè]
絕對冷卻 英文
adiabatic cooling
  • 絕 : Ⅰ動詞（斷絕） cut off; sever Ⅱ形容詞1 （完全沒有了; 窮盡; 凈盡） exhausted; used up; finished 2 ...
  • 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
  • 冷 : Ⅰ形容詞1 （溫度低; 感覺溫度低） cold:冷水 coldwater; 你冷不冷? do you feel cold?; are you feeling...
  • 卻 : Ⅰ動詞1 （後退） step back 2 （使退卻） drive back; repulse 3 （推辭; 拒絕） decline; refuse; reje...
  • 絕對 : absolute
  1. The collider has been built in eight sections, each of which must be cooled to temperatures only just above absolute zero

    碰撞機由八個部分組成，每個部分都必須冷卻到接近絕對零度。
  2. To cool atoms to near absolute zero, physicists rely on systems of lasers and magnetic fields to trap atoms

    為了將原子冷卻至接近絕對零度，物理學家倚靠的是雷射及磁場組成的系統來局限原子。
  3. In view of such case, small breweries should form adequate wort cooling procedures, barm expand propagation system and proper fermentation procedures, and establish microbial control monitoring system, which could realize thorough sterilization and washing of facilities and achieve aseptic production to improve beer quality

    中小型啤酒廠應建立麥汁冷卻工序、酵母擴培系統、發酵工序等工序和生產環節的微生物控制監測管理系統，對工藝過程及設備進行徹底清洗、滅菌，達到生產絕對無菌，提高啤酒質量。
  4. Vibration isolating grommets are standard for every hard drive and a complex airflow cooling design to maximise airflow and cooling effects with minimum noise

    振動絕緣索環對每種硬盤驅動器和復雜的氣流冷卻設計最大限度的氣流和最小限度噪音的冷卻效果中的一種標準。
  5. In the program, the effect of lamination placement, construction interval, elastic modulus change, thermal insulation change, surrounding temperature change, concrete creep and autogenous volume change on thermal stress are considered. and such temperature control measurement as water pipe cooling, heat preservation of the dam surface, the pouring temperature control, the overflow across the dam top during flood season can also be simulated by numerical method

    該程序在編制過程中考慮了混凝土分層澆築、施工間歇、彈模變化、絕熱溫升過程、環境溫度的變化、混凝土徐變、自生體積變形等因素對壩體溫度場及溫度應力場的影響，同時也考慮了水管冷卻、壩體表面保溫、控制澆築溫度、施工汛期壩頂面過水等各種溫控措施的數值模擬。
  6. In computation the effect of thermal insulation, elastic modulus, creep degree and autogenous volume change along with age, the progress of pouring by layer, work suspension in summer, the change of air temperature, heat preservation, water cooling, and water storage, by stages on temperature field are considered

    計算中考慮了混凝土的絕熱溫升、彈性模量、徐變度和自生體積變形隨齡期的變化以及分層澆築、夏季停工、外界氣溫變化、表面保溫、通水冷卻及分期蓄水等因素對壩體溫度應力場的影響。
  7. Of the riders in the tumbrils, some observe these things, and all things on their last roadside, with an impassive stare ; others, with a lingering interest in the ways of life and men. some, seated with drooping heads, are sunk in silent despair ; again, there are some so heedful of their looks that they cast upon the multitude such glances as they have seen in theatres, and in pictures

    死囚車上有人注意到了上述種種和自己最後的路上的一切，卻只冷漠地呆望著有人表現出對生命和人的依戀有人垂頭坐著，沉入了無言的絕望也有人很注意自己的儀表，照他們在舞臺或圖畫里見到的樣子在群眾面前表露一番。
  8. Magnetic head is designed by six magnetic poles in symmetrical distribution, the design of excitation loop and excitation angle makes magnetic field act on welding arc region which could control welding arc effectively. the insulation, cooling and hermetization of magnetic head avoid the influence on magnetic field of outside ; miniaturization design of magnetic head could achieve different welding process

    磁頭裝置採用六磁極對稱勵磁方式設計，勵磁線圈和勵磁角度的設計使產生的磁場恰好作用於焊接電弧區域以實現對電弧的有效控制;磁頭的絕緣，冷卻，密封設計避免了焊接過程中外界因素對磁場的干擾;磁頭整體的小型化使該裝置可以實現多種形式的焊接工藝。
  9. In accordance with the water tunnel that liner have cooling pipe, thermal insulation temperature rise model adopt difference expression during its through or not water phase, and optimization back analysis of parameters is carried out

    針對本工程引水洞襯砌內布置有冷卻水管，對絕熱溫升模型在通水前後採用了不同的表達式，並分別對其進行了優化反演分析。
  10. Consequently, the first chip - trap proposal, put forward by a group at the california institute of technology in 1995, involved cooling the entire chip to near absolute zero using a bulky and expensive liquid - helium refrigerator

    所以， 1995年加州理工學院的一個小組首度提出晶片阱的構想，需要用龐大且昂貴的液態氦冷凍機，將整個晶片冷卻到接近絕對零度。
  11. Firstly, for jet array impingement cooling, the effects of the distance of adjacent holes, the impinging distance and jet reynolds number on heat transfer characteristic at the target wall are summarized under staggered holes arrangement and the same hole diameter. and then, the numerical simulation of inclined multi - hole film cooling has been studied. the influence factors examined in this case include blowing ratio and the distance of adjacent holes

    首先通過對射流沖擊冷卻方式的研究，分析了相鄰孔間距、沖擊間距以及射流入口雷諾數對沖擊靶面換熱系數的影響情況，然後對多斜孔冷卻方式進行了數值模擬，重點探討了吹風比和相鄰孔間距對絕熱溫比與壁面換熱系數的影響規律，最後，針對沖擊-發散復合冷卻流場的計算物理模型，研究吹風比、相鄰孔間距的變化對沖擊-發散復合冷卻流動與傳熱特性的影響。
  12. Under different load, when we apply this software to any time, region and cooling way, we can get the hottest spot increment and aging rating. to manufactory, the software means sounder thermal design, which will meet the load, putted forward by user, while to user, the software equal to a master who can help them decide the capacity rating of the transformer, which will fit the load. by using the software, the potential danger and the waste, caused by unfit load choice may be avoided

    研究開發了計算乾式電力變壓器負載能力的計算軟體，可對于各種絕緣結構，各種冷卻方式和任一地區、任一時間下運行的變壓器在不同運行載荷下的最熱點溫升絕緣老化率進行分析和計算，同時利用該軟體製造廠可以依據用戶提出的運行負載量給出相應的熱設計方案，用戶可根據運行負載情況利用軟體計算所需變壓器的額定容量，避免額定容量選擇不當造成隱患和浪費。
  13. Absolute distribution of laser beam intensity is gotten from comparative distribution. the absorption coefficient of material is calculated by measuring transmissive ratio. the influences on temperature increment, stress and phase of laser beam are computed with different time, window cooling, window rotating, shape and material of window, distribution of intensity

    由近場光斑相對分佈得到其絕對分佈，測量窗口透過率，求得材料的吸收系數，在此基礎上計算了出光時間長短、窗口有無冷卻、是否旋轉、窗口材料及面型、光強分佈形式對窗口溫升、應力和光束位相的影響。
  14. Especially, in the filed of high tc superconductor, the technology that the cryocooler directly cool the superconducting system has changed the traditional cooling manner, which adopts the method of low tc fluid helium ' s convection and boiling to exchange the heat. it mainly depends on the cooling manner of conducting heat through the interfacial layer between the material of superconductor and non - superconductor ( such as cu, isolator, etc )

    特別是在高溫超導領域中，由於製冷機直接冷卻技術改變了傳統的靠低溫液氦對流、沸騰換熱的冷卻方式，主要依靠超導材料與非超導材料（如銅、電絕緣材料等）固體間的接觸導熱冷卻方式，固體間界面熱阻成為影響導熱性能的關鍵因素之一。
  15. She has cooled them just shy of absolute zero ( - 459 degrees fahrenheit ) and observed their funky quantum doings, leading the way into an unexplored realm that holds implications for superconductivity ? the creation of resistance - less electrical flow

    她將它們冷卻至接近絕對零度，觀察到它們詭異的量子行為，為一個未經探索的領域開辟了一條道路，那裡蘊涵了超導的奧秘，材料的電阻可驟降至近乎零。
分享友人
分享到 Line

分享到臉書