絕熱壁溫 的英文怎麼說
中文拼音 [juérèbìwēn]
絕熱壁溫
英文
adiabatic wall temperature-
Adopt advanced technic of f4 whole cold - press to moulding and heat melt to process to make, let the lining no slot to link withal cheek by jowl connect with exterior metalpipes wall, in the state of allowwing to work keep to distort in - phase, thereby to enhance using - life of lining in the working status of opposite high temperature high vacuum, stop the ecumenic pad fluorin pipes using in condition of cold and heat alternate and minus tension to come into being the matter of padding fluorin floor shrivel to jam the flowway and plastic rip, its perfect choice use to transport medium of strong corrosive strong oxidation by modern chemical - industry corporation
採用氟塑料f4整體冷壓成型及熱熔加工等先進技術製造，使內襯層無縫搭接且與外層金屬管壁緊密粘接，在允許工作狀態下能夠保持同步變形，從而提高了襯里層在相對高溫高真空度的工況下的使用壽命，杜絕了一般襯氟管在冷熱交替，及負壓的條件下使用易產生襯塑層鼓癟阻塞流道及塑料拉裂的問題，是現代化工企業在輸送強腐蝕強氧化介質理想的選擇。Dalian kerui economics trade co., ltd. sell tapes for bonding in industry, reclosable fasteners, adhesives, polish and grind material, anti - electrostatic and insulation tape america 3m company, heat shrinkable tubing, wire and cable, electrical thermal wire and system america raychem company, masterbatch hanna - wilson, silicone products ge toshiba company and electrostatic electronic hydrotreater, water tank self - cleaning sterilizer beijing enfi company
公司經銷美國3m各種工業用單雙面膠帶尼搭扣粘接劑拋光研磨材料防靜電材料絕緣膠帶美國瑞侃公司單雙層熱縮管鉸鏈薄壁耐高溫導線電伴熱線及系統漢納威爾遜色母料ge東芝有機硅產品和各種靜電水處理器水箱自潔消毒器。The simulations results show that the spoiler is available to make the fuel and the oxidizer coming from the former to stay in the cavity for a long time, to let the fuel and oxidizer mix and burn completely. since there is a high temperature zone forming by vortex in the middle of the motor, it required a restricted thermal protection. the plate with holes decreased the vortex function in the cavity, which could not promote the combustion efficiency, but to decrease temperature in the cavity and be benefit to thermal protection of the wall
計算結果分析表明:擾流板可以使燃料和氧化劑在擾流腔內的滯留時間加長，促進燃料與氧化劑的摻混燃燒，提高燃燒效率，但由於渦流在發動機的中間部位形成了高溫燃燒區域，致使局部燃料和絕熱層燒蝕速率增大，加大了熱防護的難度;孔板結構減弱了擾流腔內迴流區的漩流作用，不能增加推進劑燃燒效率，但可以使擾流腔內的溫度降低，給壁面熱防護帶來好處。Firstly, for jet array impingement cooling, the effects of the distance of adjacent holes, the impinging distance and jet reynolds number on heat transfer characteristic at the target wall are summarized under staggered holes arrangement and the same hole diameter. and then, the numerical simulation of inclined multi - hole film cooling has been studied. the influence factors examined in this case include blowing ratio and the distance of adjacent holes
首先通過對射流沖擊冷卻方式的研究，分析了相鄰孔間距、沖擊間距以及射流入口雷諾數對沖擊靶面換熱系數的影響情況，然後對多斜孔冷卻方式進行了數值模擬，重點探討了吹風比和相鄰孔間距對絕熱溫比與壁面換熱系數的影響規律，最後，針對沖擊-發散復合冷卻流場的計算物理模型，研究吹風比、相鄰孔間距的變化對沖擊-發散復合冷卻流動與傳熱特性的影響。The demonstration of heat - transfer measuring techniques and prospect of infrared thermal mapping techniques, main parts and performance indexes of a infrared camera, functional blocks and implementation of infrared processing software, experimental facility and measuring system of the wind tunnel has been made. the model emittance was experimentally determined and the three methods correcting directional emittance were compared. those problems of the infinite - slab model thickness and constant wall heat rates hypothesis, the determination of adiabatic wall temperature were discussed in a 1 - d heat conduction analysis
本文對紅外熱圖測熱技術與應用前景、紅外熱像儀主要部件與性能指標、紅外測熱數據處理軟體功能模塊與實現、風洞試驗設備與測量系統等進行了論述，測量了模型表面發射率並對發射率隨極角變化的三種修正方法進行了對比，對一維熱傳導分析中模型壁厚半無限假設、壁面熱流定常假設、絕熱壁溫選取等進行了探討。The temperature fields of adiabatic wall and conductive wall were measured
測量了絕熱壁溫、壁溫等溫度場。Adiabatic wall temperature
絕熱壁溫The name and the code name of the pipeline, pipe material, o. d. and the thickness of pipe, transmitting medium and its temperature, insulator materital and its thickness, the orientation of the pipeline, hight of pipe center
管線名稱代號，管道材質、外徑和壁厚，輸送的介質及其溫度，絕熱層材質及厚度，支吊處管線走向，管中心（管底）標高。分享友人