統一螺紋 的英文怎麼說

中文拼音 [tǒngyīluówén]
統一螺紋 英文
unified screw thread
  • 統 : Ⅰ名詞1 （事物間連續的關系） interconnected system 2 （衣服等的筒狀部分） any tube shaped part of ...
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 紋 : 名詞（花紋; 紋縷兒） lines; veins; grain
  • 統一 : 1. （聯成整體） unify; unite; integrate 2. （一致的; 整體的） unified; unitary; centralized
  1. Short machine taps and hand taps for unified threads

    統一標準螺紋用短機用絲錐和手用絲錐
  2. Thread rolling cylindrical dies for unified threads

    統一螺紋滾絲輪
  3. Design of american unified thread gauge

    美國統一螺紋量規的設計
  4. Thread rolling flat dies for unified threads

    統一螺紋搓絲板
  5. Unj. unified inch screw threads unj thread form

    統一標準的英制螺紋
  6. Unj unified inch screw threads unj thread form

    統一標準的英制螺紋
  7. Unified miniature screw threads

    統一標準的小型螺紋
  8. Nut taps for unified threads

    統一螺紋螺母絲錐
  9. In practical application, the m10 180 bolts, which are installed in the head cover of the torque divider of ts5560 special automobile, sometimes fracture all of a sudden. according to the tests of acceleration, stress and strain, and the exciting test, it is resonance vibration that leads to the compound - bending fatigue fracture of the bolts. the exciting force caused by drive system, transmitted through the torque divider, produces a 1000 - 1500hz cyclical excitation at the junction of the bolts and head cover, which causes the first order bending resonance vibration of the bolts

    通過加速度、應力應變測試實驗和激振試驗的研究，發現ts5560特種車分動器取力器氣缸端蓋m10 180螺栓斷裂問題是由於共振引起的雙向彎曲疲勞斷裂：傳動系統工作所產生的激勵，經過分動器結構的傳遞（特別是分動器一階扭轉模態的放大） ，在螺栓的連接處產生1000 1500hz的振動激勵，其導致螺栓一階彎曲共振，在螺栓一階彎曲模態的阻尼比較小的情況下，使得螺栓產生較大的共振響應，導致螺紋處的彎曲動應力較大，疲勞壽命較低。
  10. Limits of sizes and tolerances for unified coarse screw threads

    統一粗牙螺紋尺寸與公差限制值
  11. Unified coarse screw threads

    統一粗牙螺紋
  12. Specification for cadmium - plated, mushroom - headed, unified - thread, slotted drive, bolts

    鍍鎘蘑菇頭統一螺紋開槽螺栓規范
  13. Technical specification for unified threads taps

    統一螺紋絲錐.技術條件
  14. Manufacturing tolerances on the threaded portion for unified threads taps

    統一螺紋絲錐.螺紋公差
  15. Circular screwing dies for unified threads

    統一螺紋圓板牙
  16. Gages and gaging for unified screw threads

    統一螺紋的量規和測量
  17. Specification for unified screw threads - diameters below 1 4 in

    統一螺紋規范.第3部分:直徑小於1 4英寸
  18. Specification for unified screw threads - diameters 1 4 in and larger

    統一螺紋規范.直徑為1 4英寸及更大
  19. Limit gauges for unified screw threads

    統一螺紋極限量規
  20. Specification for unified screw threads. diameters in and larger

    統一螺紋規范.第1和第2部分:直徑等於與大於1 4英寸
分享友人
分享到 Line

分享到臉書