線性尺寸 的英文怎麼說
中文拼音 [xiànxìngchǐcùn]
線性尺寸
英文
linear dimension- 線 : 名詞1 (用絲、棉、金屬等製成的細長的東西) thread; string; wire 2 [數學] (一個點任意移動所構成的...
- 性 : Ⅰ名詞1 (性格) nature; character; disposition 2 (性能; 性質) property; quality 3 (性別) sex ...
- 尺 : 尺名詞[音樂] (中國民族音樂音階上的一級 樂譜上用做記音符號 參看「工尺」) a note of the scale in ...
- 寸 : Ⅰ量詞(長度單位) cun a unit of length (=1/3 decimetre)Ⅱ形容詞(極短或極小) very little; very ...
- 線性 : [數學] [物理學] linear; linearity線性代數 linear algebra; 線性方程 linear equation; 線性規劃 line...
-
This paper deriving the theory work inflection point in the static stage characteristics curve of small measurement range linear dimension measurement. by the way of high pressure and back pressure pneumatic measure and designed the parameter of the mainly and measure spray head, which are the key component in the spray head - baffle pneumatic sensor. the different groups for the main - spray head and the measure spray head, will effect the dynamic and static stage characteristic parameter. the author have done contrast experiment and optimization design to test and verify the theory derivation whereby made the rang of show valve of pneumatic measure system measure range up to 40 u m, the sensitivity up to 100mv / u m, resolution up to 0. 05 p m, the uncertainly of measure is less than 0. o2 u m, satisfaction of requirement of groups the carboy hatch thickness size precise measure of soft shims
對高壓背壓式氣動測量用於小量程線性尺寸測量的靜態特性曲線的理論工作拐點進行了推導,對氣動測量系統中的噴嘴-擋板型氣動傳感器中的關鍵部件? ?主噴嘴和測量噴嘴的參數進行了理論設計,對主噴嘴和測量噴嘴的不同組合,將影響測量系統靜、動態特性指標的噴嘴參數進行了對比實驗和優化設計,並通過實驗驗證了理論推導,從而使氣動測量系統量程的示值范圍達到40 m ,靈敏度達到100mv m ,解析度達到0 . 05 m ,測量不確定度小於0 . 2 m ,滿足了壓縮機缸蓋軟體墊片厚度尺寸精密測量分組的要求。Electronic comparators. linear dimensional sensors. test methods
電子比較儀.線性尺寸傳感器.試驗方法Electronic comparators. linear dimensionalsensors. technical data sheet
電子比較儀.線性尺寸傳感器.技術數據表The antenna design is based on using capacitive loads and slits on two crossed narrow patches with via fed - through feed system, which can reduce the size of the antenna, improve the isolation between two ports and keep considerable bandwidth respectively
通過電容性加載減小整個天線的尺寸,通過在天線上開槽來增加天線埠之間的隔離度,採用viafed - through的饋電方式。Appropriate distance and view angle of camera were selected and linear dimension was calibrated
選擇了合適的攝像高度和攝像角度,對系統的線性尺寸進行了標定。General tolerances ; tolerances for linear and angular dimensions without individual tolerance indications ; identical with iso 2768 - 1 : 1989
通用公差.第1部分:不逐一標注公差的線性尺寸和角度尺The nonlinear dimensions are decomposed into several sets of linear dimensions, and the 3d dimension chain is projected into dimension chains of three individual directions, namely, x - coordinate direction, y - coordinate direction and z - coordinate direction. every individual dimension chain is checked with an improved algorithm of dimension testing, and the conflicting dimension is adjusted by the mechanism of dimension rank and the principle for adjusting the dimension model
介紹了各種非線性尺寸虛擬分解成線性尺寸的方法,將空間的尺寸鏈投影成x 、 y 、 z三個方向上的單向尺寸鏈,在此基礎上根據改進的尺寸冗餘判斷演算法對各單向尺寸鏈進行尺寸封閉檢查;引入尺寸的優先機制和尺寸模型調整的原則,據此對沖突的尺寸進行調整。Cellular plastics and rubbers - determination of linear dimensions
線性尺寸的測定Commercial refrigerated cabinets - methods of test - part 1 : calculation of linear dimensions, areas and volumes
商用冷藏櫃.試驗方法.第1部分:線性尺寸面積和容積的計算Test method for linear dimensional changes of plastics under accelerated service conditions
加速工作條件下塑料線性尺寸變化測試方法Testing of mineral fibrous insulating materials ; determination of linear dimensions and bulk density, plain products
礦物纖維絕緣材料檢驗.第1部分:普通製品線性尺寸和容Latex foam - determination of linear dimensions
膠乳海綿線性尺寸測定Cellular plastics and rubbers. determination of linear dimensions
泡沫塑料製品和橡膠.線性尺寸的測定Nominal linear dimensions from 1 mm to 500 mm for mechanical engineering
機械工程用的到mm公稱線性尺寸Plastics mouldings ; tolerances and acceptance conditions for linear dimensions
塑料模壓件:線性尺寸的公差和驗收條件Testing of rubber - determination of linear dimensions of test pieces and products
橡膠試驗.試樣和成品的線性尺寸的測定Thermal insulating products for building applications. determination of linear dimensions of test specimens
建築業隔熱材料.試樣線性尺寸測定Thermal insulating products for building applications - determination of linear dimensions of test specimens
建築物絕熱產品.試樣的線性尺寸測定This paper studied mainly mechanism about pneumatic sensor of small measurement range linear dimension measurement in pneumatic measure system concluding static stage and dynamic state characteristics study
主要進行用於小量程線性尺寸測量的氣動測量系統中氣動傳感器的機理研究,氣動傳感器靜態特性研究和動態響應特性研究。Standard test method for linear dimensional stability of a gasket material to moisture
襯墊受潮后線性尺寸穩定性的標準試驗方法分享友人