線狀晶體生長 的英文怎麼說

中文拼音 [xiànzhuàngjīngtǐshēngzhǎng]
線狀晶體生長 英文
filamentary crystal growth
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 狀 : Ⅰ名詞1 （形狀） form; shape 2 （情況） state; condition; situation; circumstances 3 （陳述事件或...
  • 晶 : Ⅰ形容詞（光亮） brilliant; glittering Ⅱ名詞1. （水晶） quartz; （rock） crystal 2. （晶體） any crystalline substance
  • 體 : 體構詞成分。
  • 生 : Ⅰ動詞1 （生育; 生殖） give birth to; bear 2 （出生） be born 3 （生長） grow 4 （生存; 活） live;...
  • 長 : 長Ⅰ形容詞1 （年紀較大） older; elder; senior 2 （排行最大） eldest; oldest Ⅱ名詞（領導人） chief;...
  • 晶體 : [晶體學] crystal; vitrella; crystal body; crystalloid; x-tal
  • 生長 : grow; grow up; ascent; merisis; build up; auxesis; increment; overgrowth; gain; burgeon; bourgeon...
  1. Determined by dsc. whereafter, the surface micro - morphology of both sides of tini sma thin film deposited on glass was investigated by atomic force microscope ( afm ), and the difference of morphology between the two sides is observed. it has been shown that, in the growing surface of sputtered tini film, the trend of grain to accumulating along the normal direction like a column is clearly observed, and the grain is very loose which resulted in more microcavities, but in the surface facing to glass substrate, grain is so compact that there are hardly microcavities

    通過濺射法，在玻璃襯底上淀積了tini薄膜，並在600進行了真空退火， dsc法測得其馬氏體逆相變峰值溫度為75 ，利用原子力顯微鏡，對玻璃基tini形狀記憶合金薄膜的襯底面與生長面進行了表面微觀形貌分析，發現：生長面晶粒呈現出沿薄膜法線方向柱狀堆積的趨勢，晶粒緻密性差，微孔洞多；而襯底面晶粒緻密，幾乎沒有微孔洞存在。
  2. The temperature from amorphous to crystal of tungsten oxide sol - gel films with catalyst is increased and the reason is in studying. as results of tunnel scan - afm, both pt sputtered tungsten oxide films and pt sputtered tungsten oxide sol - gel films there is distinct and out - of - order parallel line structure on the surface of amorphous. molecules of the sample tend to tetrahedron and the former has more planarer structure

    隧道-原子力顯微鏡測試結果表明:非晶態時，磁控濺射摻鉑薄膜樣品表面和溶膠凝膠摻鉑樣品表面都有明顯的平行線狀結構，長程無序，分子趨於四面體結構，只是前者比後者表面較平整;晶態時，磁控摻鉑樣品在自然生長面上原子呈平面分佈，長程有序，溶膠摻鉑樣品則呈wo6面心結構。
  3. The finite element method ( fe '. i ) is adopted to analyze the effects of the numbers of coil turns, current intensity and current frequency upon the rate of joule heat generation in details. the thermo - radiation analytical countermeasures of various types are adopted to carry out the numerical analysis of the effects of the crucible with different shapes and sizes and the blind holes with different depths opened in the tops of crucibles as well as coil positions upon the thermal field distribution whereby solving the main problem of field the thermo - field design of the induction - heating sic crystal growth system. a new combination idea of the thermo - field design obtained by means of the united design of the thermo - insulator and blind holes has been presented

    採用有限元分析方法對線圈匝數、電流強度、電流頻率等對焦耳熱產生速率的影響進行了詳細的分析討論；採用不同的熱輻射分析策略，對不同坩堝形狀、坩堝頂部開設不同深度的盲孔以及線圈的位置等對熱場分佈的影響進行了數值分析，解決了感應加熱碳化硅晶體生長系統熱場設計的主要問題，提出了通過絕熱層與盲孔的聯合設計獲得所需熱場設計的思路，給出了根據軸向溫度梯度的波動對線圈位置實行動態調節以控制熱場的理論依據。
分享友人
分享到 Line

分享到臉書