線阻應變儀 的英文怎麼說
中文拼音 [xiànzǔyīngbiànyí]
線阻應變儀
英文
wire-resistance strain gauge-
On the one hand, according the design principle of torque sensor, this paper researched the non - contact torque sensor, which base on the theory of electric resistance strain and the rotation transformer and could satisfied the request of our project as well as the condition of the producing process. on the other hand, the modulation method of torque signal has been solved before the signal was input to the industry computer, therefore, solved the problem of signal transfers
其次，研究和研製了扭矩在線測試工作所需要的儀器硬體。一方面，根據扭矩傳感器的設計原理，研製了滿足課題要求和生產現場條件的，基於電阻應變理論和電感集流環的非接觸型扭矩傳感器；另一方面，制訂了扭矩信號在輸入工業計算機之前的調理方法，解決了信號傳輸問題。According to the request of this subject, we have developed the system hardware and software for the slave device and the inspection software running on the pc. in this paper all of the followings is illustrated detailedly, such as the research on the principles of measurement and its realization, three means of water - level measurement that are separately based on photo electricity coder, pressure sensor and potentiometer ; selection of the microchip, we choose an advanced integrated soc ( system on chip ) microchip c8051f021 as the main controller ; realization of signal sampling, processing and its conversion in the mcu ; application of high precision 16 bits adc cmos chip - - ad7705 in our system, designing its interface with the microchip and relevant program ; using a trickle charge timekeeping chip ds1302 in the system which can provide time norm and designing of its i / o interface and program ; additionally, a 4 ~ 20ma current output channel to provide system check - up using ad421. in the system, ad421, ad7705 and the microchip compose spi bus ; to communicate with the master pc, here we use two ways which are separately rs232 and rs485 ; moreover, there are alarm unit, keyboard unit, power supply inspection unit and voltage norm providing unit in the system
針對研製任務的要求，課題期間研製了下位機系統硬體和軟體，開發了上位機監控軟體，其中所作的具體工作包括：測量原理的研究和在系統中的實現，在本次設計中用三種方法來進行水位測量，分別是旋轉編碼器法、液位壓力傳感器法和可變電阻器法；主控晶元的選擇，我們選用了高集成度的混合信號系統級晶元c8051f021 ；實現了信號的採集和處理，包括信號的轉換和在單片機內的運算；高集成度16位模數轉換晶元ad7705在系統中的應用，我們完成了它與單片機的介面設計及程序編制任務；精確時鐘晶元ds1302在系統中的應用，在此，我們實現了用單片機的i o口與ds1302的連接和在軟體中對時序的模擬，該晶元的應用給整臺儀器提供了時間基準，方便了儀器的使用；另外，針對研製任務的要求，還給系統加上了一路4 20ma模擬信號電流環的輸出電路來提供系統監測，該部分的實現是通過採用ad421晶元來完成的，本設計中完成了ad421與單片機的spi介面任務，協調了它與ad7705晶元和單片機共同構成的spi總線系統的關系，並完成了程序設計；與上位機的通信介面設計，該部分通過兩種方法實現： rs232通信方式和rs485通信方式；系統設計方面還包括報警電路設計、操作鍵盤設計、電源監控電路設計、電壓基準電路的設計。In the eddy - current testing, testing coil is the sensitive component connecting the specimen and the instrument, so it is called transducer. the information of the test specimen is reflected by the variation of the coil impedance ( or induced voltage )
在渦流檢測中，檢測線圈是用來連接測試儀器和被測試件的敏感元件，它是渦流檢測中的傳感器，被檢試件的信息是通過線圈阻抗（或感應電壓）的變化反映出來的。Standard test method for linear coefficient of thermal expansion of rock using bonded electric resistance strain gages
用粘結的電阻應變儀測定巖石熱膨脹線性系數的標準試驗方法分享友人