縮尺律 的英文怎麼說
中文拼音 [suōchǐlǜ]
縮尺律
英文
scaling law-
The plexiglass model test is carried out by two selective shape, the stress of each test operating loads was obtained in order to validate the correctness of the finite element modeling. in this paper, a regularity of shear lag effect of main sections in two kinds of box girder is given. as the foresight project of double - level - driveway continuous box girder, this research fully utilizes the space of box girder structure and flexural and torsional properties of high - depth box girder, which have innovative significance and applied foregroundin engineering
對所選擇的結構形式進行縮尺有機玻璃模型試驗,得到實腹連續箱梁和空腹箱梁在各種試驗工況荷載下的應力,通過換算分析,驗證了本文所建立的有限元模型的準確性,由此得到兩種箱梁各主要斷面剪力滯效應的變化規律。Long parts, ( such as axis, pole and so on ) varying along the profiled bar direction by the length or by a certain rule can be shortened to represent, and the broken part shall be represented by waved line or zipped lines, as shown in fig. 13
較長的機件(軸、桿、型材等)沿長度方向的形狀相同或按一定規律變化時,可斷開后縮短繪制,斷開后的結構應按實際長度標注尺寸;斷裂邊界可用波浪線、雙折線繪制,如圖13所示。Minzheng zhang , xun guo , qingli meng , study on shaking table tests of building models , china - us millennium symposium on earthquake engineering , beijing , china , 2000
參與科研項目「地震模擬振動臺試驗縮尺模型一致相似律及其應用研究」 ,獲中國地震局防震減災優秀成果三等獎, 2002 。This paper takes jin ’ ao mansion and adjacent buildings as the study object. first we put the stated reduced scale model in the atmospheric boundary layer which the tunnel simulates, applied the dynamic pressure measure technology on the building ’ s surface to get the mean and fluctuating wind pressure coefficient, drew out the contour of pressure coefficient and analyzed its distributing law and characteristic
本文以金奧大廈及其鄰近建築作為研究對象,首先把一定縮尺比的模型置於風洞模擬的大氣邊界層環境中,運用建築表面動態測壓技術獲得金奧大廈表面的時均風壓系數和均方根風壓系數,繪制時均風壓系數和均方根等值雲圖並分析其分佈的規律和特點。The solving object is a set of governing equations of a flow field with weak compressibility. we also simulate the dispersion characteristic and concentration field of solid particles of various typical sizes in the jet field with one - way coupling method
本文的求解對象為有弱可壓縮性的流場控制方程組,並採用單向耦合的方法模擬各種典型尺寸的顆粒在射流流場中的擴散行為和濃度分佈規律。In this paper, based on analyzing the forming regularity, geometric characteristic and dimensioning factor of primitive and combined entity, the notion of explicitly feature position of geometric shape of primitive is introduced, the classification is dicussed. the notion of explicitly feature position constraint of geometric shape of combined entity is introduced. the classification, the explicitly reductive property for location dimension, the constraint of the explicitly feature position constraint of geometric shape of combined entity degree are systematically analyzed
本文通過對基元體和組合體的形成規律、幾何特性及尺寸要素分析的基礎上,引入了基元體和組合體的隱式幾何形狀特徵位的概念,系統地分析了隱式幾何形狀特徵位約束的分類、及其約束度等概念;提出了定位尺寸預先加入的策略及隱式幾何形狀特徵位約束對定位尺寸的隱含性縮減的性能,並建立了求解組合體的尺寸約束解的推理求解公式;通過引入基元體的隱式幾何形狀特徵位和組合體的隱式幾何形狀特徵位約束等概念,把尺寸約束解的求解轉化為對基元體的隱式幾何形狀特徵位相互之間的位置關系。Abstract : a probability calculation formula used for the cavity dimension of injection mold is derived on the basis of analysing the variation rule of plastic shrinkage rate, and a quantitative relation among the variation of plastic shrinkage rate, plastics dimension tole - rance, manufacturing tolerance and wear allowance is discussed
文摘:在分析塑料收縮率波動規律的基礎上,導出了注塑模成型零件工作尺寸的概率計算公式,討論了塑料收縮率波動范圍、塑件尺寸公差、製造公差以及修模裕磨量之間的關系。Since metal - oxide - semiconductor ( mos ) device appeared, integration of integrated circuit ( ic ) expands as moore law. meanwhile the dimension of device scales down, the thickness of sio2 gate dielectric shrinks as the same law. but as the thickness of sio2 gate dielectric reaches at isa, the gate current rises very quickly and reaches at 1 10a / cm2
自從金屬-氧化物-半導體( mos )器件出現以來,集成電路的集成度按照摩爾定律增加,相應地,器件的物理尺寸按照等比縮小的原則不斷縮小, sio _ 2作為柵介質的厚度不斷縮小,特徵尺寸在0 . 1 m以下的集成電路要求sio _ 2柵介質的厚度小於1 . 7nm 。分享友人