縱向拉桿 的英文怎麼說

中文拼音 [zōngxiànglāgǎn]
縱向拉桿 英文
fore-and-aft rod
  • 縱 : Ⅰ動詞1 （釋放; 放走） release; set free; let go 2 （放任; 不約束） indulge; give oneself up to; l...
  • 拉 : 拉構詞成分。
  • 桿 : 桿名詞（桿子） pole; staff
  • 縱向 : [造紙] direction; machine direction; endwise; longitudinal direction; vertical; longitudinal縱向...
  • 拉桿 : bar; straining beam; drawbar; dog iron; stake pole; queen bolt; tie rod; pull rod; drag link; ten...
  1. The mechanism consists of a steering gear box, pitman arm, drag kink, tie rods, steering arms, and steering knuckles, the latter supporting the front wheels

    該機構由轉向器，轉向垂臂，縱拉桿，轉向橫拉桿，梯形臂和轉向節構成，轉向節支承著前輪。
  2. You can ease back ( ease back on ) the stick and gain a little height

    你可以把操縱桿向後拉一拉，讓飛機飛高一些。
  3. Firstly, for the system of moulding board and support frame in construction the side pressure and screws are analyzed. the material and structure form of support frame are discussed. the design of support frame uses the method of limited state, and also it analyses the integer stability, part stability, and single stability, and then proposes the load analysis of multi - level support frame

    首先，針對轉換層梁模體系及支撐架施工，重點分析了轉換層結構現澆混凝土對模板側壓力值及模板對拉螺桿的計算；討論了轉換層支撐體系的形式及構造，詳細論述了基於極限狀態設計的支撐架計算方法，包括縱橫向水平桿的強度驗算、立桿的整體穩定性、局部穩定性、單肢桿件穩定性等驗算，並提出了多層支撐架的施工荷載計算方法。
  4. The kinematic performance of the macpherson suspension on a real vehicle is studied, and the changes of the front wheel alignment and the motion of the front wheel in the longitudinal and the transversal directions are figured. based on the requirements of general layout, a constrained optimization design model is set up with the steering cross rod ball joint position as the optimization variables ( design parameters ), and the sum of steering cross rod length interference while the left front wheel turning and bouncing as the objective function. and the optimization results are worked out by programming on computer

    針對一種實際車型上的麥弗遜式懸架，計算分析了轉向輪跳動時前輪定位角和車輪橫向、縱向滑移量的變化情況，並根據實際車型上麥弗遜式懸架的空間布置要求，建立了以轉向橫拉桿斷開點空間位置坐標為優化變量，轉向橫拉桿斷開點空間布置坐標可變化范圍為約束條件，車輪轉向和跳動時轉向橫拉桿長度干涉量為目標函數的約束優化設計模型。
  5. In order to reveal load mechanism and failure mode of thick pile caps, by means of the test of 1 / 4 - scale models of thick pile caps with six piles and post - handling study of 3 - dimensional non - linear finite element adina, this paper points out the shortage, which is that the design of pile caps is carried out by flexural strength in chinese technical code for building pile foundations jgj94 - 94 and american reinforcement concrete building construction code aci318 - 02, promulgates that the failure mode of thick pile caps is punching failure and load transfer mechanism is the strut - and - tie, which is that zones of concrete with primarily unidirectional compressive stresses are modeled by compress struts, while tension ties are used to model longitudinal reinforcement over pile

    摘要為揭示厚承臺的傳力機理和破壞形式，通過對4個1 : 5比例的六樁厚承臺的模型試驗研究與三維非線性有限元adina的后處理研究，指出中國建築樁基技術規范jgj94 - 94與美國鋼筋砼房屋建築規范aci318 - 02規范中，承臺以彎曲強度進行配筋計算的設計方法之不足，揭示出厚承臺的破壞模式是沖切破壞，傳力機理是以帶有主要單向壓應力的砼區域作斜壓桿，樁頂區域的縱筋作拉桿的空間桁架。
  6. The main contents are as follows : firstly, the structure and characteristics of aqueduct - stayed are summarized, based on which the structure analysis is presented ; planar structural models are established to simplify the analysis of internal force and displacement of aqueduct - stayed based on moment - distribution theory, the formula to calculate the force of cross section of aqueduct - stayed is derived. the finite element method for framed structures is used to analyze the aqueduct body. and corresponding computer programs are developed

    為便於計算，在計算斜拉渡槽的內力及變形時，將空間結構簡化為平面結構，分別對槽身橫斷面及槽身縱向結陶進行計算：以力矩分配法為基礎推導了槽身橫斷面內力的計算公式；運用直接剛度法，編制了桿系有限元程序進行槽身縱向結構計算，並簡單介紹與斜拉渡槽相關的剛度法知識以及程序的流程圖。
  7. Aerospace ; lever - operated, two - position, on off switches, directions of operation

    航空和航天.拉桿操縱的雙位on off開關.操縱方向
分享友人
分享到 Line

分享到臉書