繼電器整定 的英文怎麼說

中文拼音 [jìdiànqìzhěngdìng]
繼電器整定 英文
relay setting
  • 繼 : Ⅰ動詞（繼續; 接續; 接著） continue; succeed; follow Ⅱ副詞（繼而） then; afterwards
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 繼電器 : [電工] electric relay; relay
  1. Pre - data gathering module achieves the collection and communication of sixteen - route temperature signal. speed measuring and controlling module realizes the control of refolw soldering transfer speed by manipulating transducer. on - off outputting module fulfills calefaction control of calefaction tube by solid state relay. above position operator software programs by delphi, and realizes pid parameter automatic timing and no - oversnooting temperature control. software has friendly interface, convenient operation, complete functions

    前置數據採集模塊完成16路溫度信號的採集和通訊；速度測量模塊與速度控制模塊通過控制變頻器來調節迴流焊的傳輸速度；開關量輸出模塊通過固態繼電器對加熱管進行控制；上位機軟體採用delphi編程，實現了pid參數自整定以及無超調的溫度控制。
  2. Abstract : there are only two set values ( 30, 45 ) for interior angle of the stimulated directional power relay as the protection in phase to phase short circuit fault. an accurate setting formula for interior angle of the microprocessor - based directional power relay as the protection in phase to phase short - circuit fault is proposed and analyzed, users can set as a calculation value or at least an optimum in the formula. therefore the operation sensitivity and reliability of the directional relay would be improved greatly. the opinion is new and practical

    文摘:保護相間短路的模擬式功率方向繼電器內角的整定值只有兩個（ 30 、 45 ） ，用戶只能在這兩個值中選其一；分析並提出了保護相間短路的微機型功率方向繼電器內角的準確整定計算公式，用戶可以整定為該公式的計算值或至少為最合理的值，從而能顯著提高方向繼電器的動作靈敏度及可靠性，具有新見解及應用價值。
  3. In hardware designing, the feasibility to use a / d acquisition board, signal conditioning board and the relay output board which are more professional at present to construct the hardware of the computer control system was explored, the algorithm pid was used to advance the respond to error and stability of the whole system, through selecting proper a / d, d / a, di / do board cards, a special computer control system was constructed. in software designing, the language borland c + + was

    在硬體設計上，探索採用目前較為專業化的a / d轉換卡、信號調理板和繼電器輸出板構成計算機控制系統硬體結構的可行性，並採用pid控制以提高系統對誤差的響應和整個系統的穩定性，通過選用適當的a / d 、 d / a 、 di / do等板卡，構成一個很有特色的計算機控制系統。
  4. This paper discusses the ability of avoiding maximal power flow of quadrilateral impedance relay and round impedance relay in detail and puts forward the setting principle and setting method of load limiting resistor of backup distance protection

    本文對四邊形和方向圓特性阻抗繼電器躲線路最大潮流的能力進行了詳細分析，提出了距離保護負荷限制電阻的整定原則和整定方法。
  5. Zelio family becomes much integrated covering timer, counter and measurecontrol relay products and plug - in relay launched already. the zelio products will gradually be complete for your choice of low end component products

    Zelio家族繼中間繼電器之後又將有一系列新產品推出，從定時器、計數器，到測量與控制繼電器，逐步形成一個完整的小型元器件產品系列。
  6. Time setting range of relay

    繼電器時限整定范圍
  7. Dexterous control due to the low consumption & wide voltage range dc coil inside, while electronic thermal overload relay provides precise protection against all kinds of fault

    低功耗、寬電壓范圍接觸器線圈，寬范圍整定電流（ 4倍）電子式熱繼電器，控制保護精準無誤；
  8. This paper describes the designing principle and method of hardware and software of this system, especially discusses the precise control of the temperature and pressure in theory. we adopted the new method of intelligent pid parameters auto - tuning - - relaying pid auto - tuning. this kind of parameters auto - tuning technique fully abandons the operation of modeling and sub - modeling, and directly tune the parameters by investigating the close - loop capacity

    論文就該系統的硬體設計原理、軟體設計原理作了論述，特別對溫度和壓力的精確控製作了理論上的研究，採用了新型的智能pid參數自整定策略? ?繼電型pid自整定，這種控制器參數自整定技術完全摒棄了建模與建子模的運算，通過對閉環性能的測試，直接進行整定參數的操作。
  9. Data inputting and graphinputting module respectively achieve data inputting of first system and electric firstwiring diagram inputting ; secondary scheme design module realizes scheme design ofsecondary loops including control, protection, signal, measure, automotive equipment, operation electrical source and electrical source for substation and power distributionstation, using rule - cased reasoning of expert system ; protective relaying settingcalculation module realizes setting calculation for first equipments which aretransformers, circuitries, capacitors, and electromotors ; secondary equipmentselection module realizes type selection of secondary microcomputer integratedequipments ; graph making out module realizes secondary drawings making outautomatically representing design production using case - cased reasoning of expertsystem and the drawings can be edited and modified under the secondary developedautocad environment

    數據輸入和圖形輸入模塊分別完成一次系統資料錄入和電氣主接線圖的輸入;二次方案設計模塊利用專家系統基於規則的推理實現變配電所各二次迴路的方案設計，包括控制、保護、信號、測量、自動裝置、操作電源和所用電源;繼電保護整定計算模塊實現主設備的整定計算，包括變壓器、線路、電容器和電動機;二次設備選型模塊實現二次微機成套裝置的型號選擇;圖形生成模塊利用專家系統基於實例的推理實現代表設計成果的各類二次圖紙的自動生成，生成的圖紙可以在二次開發的autocad環境下進行編輯和修改。
  10. Among this article, the principle, design method and result of relays, especially the permanentmagnetism rotation - balancing relay, will be dissertated. a kind of relay design solution is proposed. so it has some practical meaning

    本文對繼電器，特別是帶永磁的旋轉平衡式繼電器的計算機輔助設計的相關原理、設計方法和結果做了完整的闡述，提出了一類繼電器設計的解決方案，具有一定實踐意義。
  11. Answer : preparative job includes : understands workplace one, the moving circumstance of 2 equipment, this job has with moving equipment without direct connection, have the job that cooperates without need with other team and group ; makes working priority discipline and the blemish that prepare to solve and weak point ; the staff member makes clear to divide the work and be familiar with the concerned data such as blueprint and test gauge cheng ; should be had the blueprint that agrees with actual state, record that examines last, newest rectify spare parts of the instrument that decides requisition, test gauge cheng, qualification, machine parts or tools kept in reserve, tool and join lead to wait ; is a few righter important equipment, especially complex protector or couplet jumps loop protector, should weave test program, working controller should fill in ticket of protection safety precaution, examine and approve via technical chief, just can carry out

    答：預備的工作包括：了解工作地點一、二次設備的運行情況，本工作與運行設備有無直接聯系，與其他班組有無需要配合的工作；制定工作重點項目及預備解決的缺陷和薄弱環節；工作人員明確分工並熟悉圖紙與檢驗規程等有關資料；應具備與實際狀況一致的圖紙、上次檢驗的記錄、最新整定通知單、檢驗規程、合格的儀器、備品備件、工具和連接導線等；對一些重要設備，非凡是復雜保護裝置或有聯跳迴路保護裝置，應編制試驗方案，工作負責人應填寫繼電保護安全措施票，並經技術負責人審批，方能實施。
  12. Firstly, the paper introduces the classic methods of the pid parameter tuning in the past years ; secondly, it introduces the relay self - tuning method and the fuzzy logical self - tuning of pid parameter ; lastly, it presents the new method, and uses a plant of one order plus time - delay on matlab to simulate. the there methods ’ ? ? zn - method, relay self - tuning on pm method and the new method simulation results show that : the new strategy of pid parameter tuning is very good at control performance, and has good behavior in disturbance - rejection performance

    本文首先綜述了近幾十年來經典pid控制器參數整定方法;然後詳細介紹了繼電pid整定法以及模糊pid參數整定法，並分別對這兩種方法的整定效果進行了模擬研究與分析;最後，提出了本文的整定法，並用matlab以一階慣性加時滯模型為研究對象，對zn法整定法、基於pm法繼電整定法和本文提出的方法的整定效果，進行了模擬研究與比較。
分享友人
分享到 Line

分享到臉書