纖維纏繞法 的英文怎麼說

中文拼音 [xiānwéichánràofǎ]
纖維纏繞法 英文
filament winding process
  • 纖 : 纖形容詞（細小） fine; minute
  • 維 : Ⅰ動詞1 （連接） tie up; hold together; link 2 （保持; 保全） maintain; safeguard; preserve; keep ...
  • 纏 : Ⅰ動詞1. （纏繞） twine; wind 2. （糾纏） tangle; tie up; pester 3. [方言] （應付） deal with Ⅱ名詞（姓氏） a surname
  • 繞 : 繞名詞1. [書面語] （彎曲） bend2. （姓氏） a surname
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 纖維 : fibre; staple; filamentary
  • 纏繞 : 1 （條狀物迴旋地束縛在別的物體上） twine; bind; wind; swathe; enwind; intertwine; wind up; convol...
  1. The research work of this article is a part of the " reliability research of cylinders for compressed natural gas vehicles " project which was subsidized by chongqing scientific committee, it aims to research the destructive theory and design theory and method for fiber enlaced composite materials shell, and synthetically use finite element optimal technology to set up composite materials cad system

    本文的研究工作是重慶市科委資助項目「天然氣汽車氣瓶可靠性研究」的一部分，旨在研究纖維纏繞復合材料殼體設計理論及方法和破壞機理，綜合運用有限元優化技術建立復合材料殼體cad系統。
  2. A ' method of analyzing the stresses of the lining of fiber enlaced composite cylindrical shell under internal pressure is raised through building the theory equation with putting the ring shaped stiffener on the point of enlancing fiber. the result is good fit with the traditional finite element analyzing system

    並結合對承受內壓的纖維纏繞復合材料圓柱殼進行了分析，通過建立理論方程提出了把加強環點建立在纖維纏繞處分析圓柱殼內襯應力應變的方法，計算結果與傳統有限元分析系統計算結果相吻合。
  3. On the other hand soccer balls can be made in hand sewing, machine sewing and glue sticking

    除內膽和纏繞纖維不同外，表面材料為人造皮革或橡膠等，製造方法有手工縫制、機器縫制以及膠粘等。
  4. Test method for interlaminar shear strength of ring of filament - winding reinforced plastics

    纖維纏繞增強塑料環形試樣剪切試驗方法
  5. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  6. The paper tries to adopt a new method - fw to mould it

    本文試圖用一種新的加工方法? ?纖維纏繞（ fw ）來成型機翼蒙皮。
  7. Fibre - reinforced plastics - methods of producing test plates - filament winding

    纖維增強塑料.試驗板的制備方法.長纖維纏繞
  8. Fibre - reinforced plastics - methods of producing test plates - part 5 : filament winding

    纖維增強式塑料製品.試驗板的生產方法.第5部分:長纖維的纏繞法
  9. According to the transferring matrix method, the paper presents a method for calculating the deflection of a filament wound tapered tube at bending and the calculation result is proved by experiment results

    本文以傳遞矩陣法為基礎，計算纖維纏繞錐管在彎曲載荷作用下的撓曲變形，並以實驗結果驗證了計算結果。
  10. The main contents of the paper are : ( 1 ) review the state and art for fiber - wound vessel with metal inner lining ; ( 2 ) provide a method to present the technical features including wound process, equal stress dome and fiber gathering at the dome etc. ( 3 ) establish a finite element analysis model considering nonlinear physical and geometrical effects and develop a equivalent constitutive relation for winding graphite fiber reinforced plastic layers ; ( 4 ) set up a failure criterion for the inner metal lining and winding graphite fiber reinforced plastic layers ; ( 5 ) develop a corresponding engineering analysis code based on the commercial software ansys ; ( 6 ) investigate the plastic deformation and residual stress in the inner lining due to winding tension and pre - tension, and stress distribution of the composite vessel under service loading case

    本文旨在為具有金屬內襯的纖維纏繞復合容器的參數設計提供分析模型、方法及工程軟體。論文主要內容是： （ 1 ）對復合容器分析國內外研究的概述； （ 2 ）復合容器的幾何表徵方法及工藝中若干力學問題； （ 3 ）復合容器結構分析的物理和幾何非線性有限元列式及其纖維層的等效本構關系； （ 4 ）復合容器的破壞類別； （ 5 ） ansys程序的二次開發； （ 6 ）典型復合容器的數值討論。本論文工作將對工程界復合容器設計和分析工作者具有參考價值。
  11. On the other hand, for the pre - press stress being threw by the hub was inserted after cooling with liquid nitrogen, the poor transverse tension strength of the multi - ring flywheel rotor could be counteracted. so the rotate speed and energy storage density can be increased efficiently

    而採用多環套裝纏繞技術製造的多層飛輪輪環，在利用溫差過盈裝配方法給復合材料輪環施加預壓應力后，能夠有效避免飛輪轉子的復合材料輪環部分因較低的纖維橫向抗拉強度而破壞失效，從而大幅度提高飛輪轉子的極限轉速和儲能密度。
  12. Chapter 6 discusses post processing of fiber paths and collision control during winding, proposes mathematical principles and detail algorithm of generating machine paths. finally, examples of elbow fabrication are shown in chapter 7 to prove the reliability of this system

    第六章討論了纏繞彎管cam ? ?纖維路徑后處理，研究了纏繞機加工彎管時各運動軸之間的碰撞控制和纖維束扭曲問題，給出了生成機器路徑的數學原理；建立了計算機器路徑的方程組，並給出了脫機生成機器路徑的具體演算法。
  13. Test method for thermal endurance of varnished fibrous or film wrapped magnet wire

    漆包纖維或薄膜纏繞磁線的耐熱性標準試驗方法
  14. Standard test method for thermal endurance of varnished fibrous - or film - wrapped magnet wire

    漆包纖維或薄膜纏繞磁線的耐熱性標準試驗方法
  15. It involves the way of measurement and control strategy. this article focuses on measurement and control of resin viscosity in microcomputer control fiber winding machine or dipping glue machine

    本文研究的是應用於微機控制纖維纏繞機或浸膠機的樹脂粘度的測量與控制，根據實際情況選擇性價比高且操作簡單的單筒式旋轉測量法測量樹脂粘度。
  16. Stability of geodesies on torus and semi - geodesies on cylinders are discussed in chapter 4 ; the definition of algebraic pattern of filament winding elbows and pattern design method are given in chapter 5, and this method is able to design the fiber path with uniform coverage

    在此基礎上，給出了保證不打滑、不架橋的纏繞幾何模式。第五章研究了纖維纏繞彎管的纖維分佈問題? ?代數模式，提出了纏繞彎管的代數模式定義和能均勻覆蓋彎管的設計方法。
  17. At present, there is no cad / cam software for non - axisymmetric filament winding in china. this paper researches into method to design fiber paths of non - axisymmetric filament winding, generalizes splines in traditional cagd, successfully applies them to the fiber path design of winding elbows, presents mathematical principles and methods of winding elbows, and develops a cad / cam system for elbow fabrication

    本文研究了非軸對稱纏繞的纖維路徑設計方法，推廣了傳統cagd中的樣條技術，並成功地應用於纏繞彎管的路徑設計中；提出了復合材料彎管的纖維纏繞數學原理和方法，並研製開發了一套纏繞彎管cad cam系統。
  18. Fabrication method of ring test

    纖維纏繞增強塑料環形試樣製作方法
  19. Fabrication method of ring test specimen for filament - winding reinforced plastics

    纖維纏繞增強塑料環形試樣製作方法
  20. In this article, the following technology of the carbon fiber composite flywheel in the integrated energy - storage / attitude - control system are analyzed and the valuable achievements are achieved above the foundation of consulting a large quantity of literatures and investigation : 1. different technology method for carbon fiber composite flywheel are designed, aimed at the character of carbon fiber composite material and manufacture 2analyzes the stress of carbon fiber composite flywheels made by different technology method, hoop - winding method, symmetric ortho layers pressing method, multi - layer winding method and interference joining method, under high rotate speed, builds their static model ; and simulates their technology and shape parameter ' s affecting their stress level with i - deas f. e. m

    本文在查閱了大量國內外相關文獻及調研的基礎上，針對集成化儲能/姿態控制飛輪系統中的碳纖維復合飛輪的以下相關技術進行了研究，並取得了有價值的成果： 1針對碳纖維復合材料的特點及加工方式，設計了周向纏繞成型法、對稱正交鋪層層壓法、多層結構纏繞及過盈連接法等不同工藝方式的碳纖維復合飛輪轉子； 2針對不同工藝方式的碳纖維復合飛輪轉子，進行了高速旋轉狀態下的應力分析，建立了靜力學解析模型，並結合i - deas有限元分析軟體模擬模擬了不同工藝方式的碳纖維復合飛輪轉子的相關幾何參數及工藝參數對其應力水平的影響； 3
分享友人
分享到 Line

分享到臉書