翹曲模型 的英文怎麼說

中文拼音 [qiáoqūmóxíng]
翹曲模型 英文
warped pattern
  • 翹 : 翹動詞（一頭向上仰起） stick [hold] up ; bend [turn] upwards; curl up
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 模型 : 1 （仿製實物） model; pattern 2 （制砂型的工具） mould; pattern3 （模子） model set; mould patter...
  1. Abstract : thermally induced stress and the relevant warpage cause by inappropriate mold design and processing conditions are problems that confounded the overall success of injection molding. a thermorheologically simple thermoviscoelastic two - dimension material model is used to simulate the residual stress and warpage within injection molded parts generated during the cooling stage of the injection molding cycle. the initial temperature field corresponds to the end of the filling stage. the fully time - dependent algorithm is based on the calculation of the elastic response at every time step. numerical results are discussed with respect to temperature and pressure

    文摘:不均勻的熱殘余應力及其變形是注塑成型加工中常見的工程問題之一.應用熱流變簡單材料的二維熱粘彈本構方程得到的遞推公式，數值模擬了成型中的熱殘余應力及其翹曲變形，並用數值實驗討論了溫度、壓力對注塑件殘余應力及變形的影響，發現溫度變化不均勻是注塑件翹曲變形的最主要原因，其影響遠大於壓力的作用，與工程實驗的結論一致
  2. The camber development mechanism and the influence factors were researched by geometry analysis, viscous analysis and sintering kinetics analysis. the camber model was established and the equation for calculating curvature of camber was proposed. the influence factors for camber involve the original size of composite, the sintering properties and the shrinkage mismatch between the two materials

    從幾何學、粘彈性力學和燒結動力學的不同角度出發，探討了共燒翹曲形成機制和影響因素，建立了介電材料鐵氧體材料疊層共燒翹曲模型和翹曲曲率方程，揭示影響翹曲的因素為形狀尺寸因子，材料的燒結特性和異種材料之間的收縮率差，其中燒結過程的收縮率差是翹曲產生的根本因素，收縮率差越大，則翹曲曲率越大。
  3. Numerical simulation of warpage of injection - molded parts

    注塑製品翹曲變形數值分析模型
  4. Under certain conditions, the calculating formula of interlayer stress and the stress - distributing diagram in cut planes are provided, and the mathematical model for warpage deformation calculation is also established

    建立了翹曲變形的數學模型，討論了各種工藝參數（層數、掃描線長、成型室溫度、層厚等）對翹曲變形量的影響。
  5. As the basis of stochastic torsional analysis, a stepped thin - walled beam model with complex cross - sections of arbitrary shapes ( open, closed or mixed ) is established in this paper, which takes into account the effect of secondary shear flow resulting from warping restraint

    摘要具有復雜斷面形狀的階梯精密梁模型作為扭轉隨機分析的基礎，可以計及翹曲約束引起的二次剪流。
  6. Now, it is important to develop the composite blade researching, two measures including analysis methodology and finite methodology are provided. in this text, the finite rotation composite beam theory developed by hodges and his co - workers, during the late 1980 ' s, is adopted in order to research rotor of helicopter. a liner and two - dimension finite analytic measure is used to calculate the section characteristic and strain of the blade ; a semianalysis methodology is used to calculate the sensitive degree of section characteristic

    以giavotto的線性二維有限元分析模型為基礎考慮了復合材料槳葉的結構和變形特點，計入了剖面翹曲的影響，在此基礎上編制了具有八節點等參元復合材料槳葉剖面剛度計算的有限元程序，分析計算了復合材料梁的剖面剛度、彎曲中心、剪切中心；並利用半解析法進行剖面剛度、剪切中心、彎曲中心的參數靈敏度分析。
  7. By model experimentation of 14 high - strength concrete frame columns subjected to axial eccentric compression, shear and humdrum torque, of 9 high - strength concrete and 3 high - performance concrete frame columns subjected to biaxial eccentric compression, shear and reversed torque, the behavior of high - strength concrete frame column in warped section are studied the first time, and the mechanism of torsion bearing capacity of high - strength concrete frame column are discussed

    通過14根承受單向壓、彎、剪，單調扭矩復合作用的高強鋼筋混凝土構件和9根高強混凝土、 3根高性能混凝土框架柱在雙向壓彎剪反復扭矩復合作用的模型試驗研究，首次研究了高強混凝土框架柱在翹曲截面上的受力行為，探討了高強混凝土框架柱抗扭性能的受力機理。
分享友人
分享到 Line

分享到臉書