能承受載荷 的英文怎麼說
中文拼音 [néngchéngshòuzǎihé]
能承受載荷
英文
able to support load-
A statically indeterminate structure will usually sustain loads in excess of that at first yield before instability occurs.
超靜定結構通常在失穩之前,既使超過第一個屈服點還能承受載荷。Therefore, the prestress of the cable should make sure that the cable is in the tight state in the entire process. the largest wind load which the prestressed cable truss can undertake is studied emphatically in the article
因此,索中初始預應力應能保證索在工作的全過程中始終處于張緊狀態,以此為條件,本文重點研究了預應力索桁架所能承受的最大風荷載值。This kind of high silica wrought aluminum alloy is provided with low density and well heat - stability, especially with the metallurgical structur ? similar with bearing alloy ? which is composed of dispersion distribution common silicon crystal hard mass point and the alloyed basal body is very fit for the components manufacture ? can bear small capacity moving load and friction load
這種高硅變形鋁合金具有密度小和200以下良好的熱穩定性,特別是它的由彌散分佈的共晶硅硬質點及合金化的相基體組成的類似軸承合金的金相組織、特別適合用於製做承受小能量動載荷和摩擦載荷的零件。According to the development of the society and economy, pile foundations have played more and more important effects in the development of modern civil engineering. at present, pile foundations in the offshore petroleum platforms, super high - rise buildings and long span bridges, should not only bear vertical loads but also accept horizontal loads to adapt high, heave, large buildings
目前我國海洋石油平臺、超高層建築、大跨度橋梁等中所使用的樁基礎不僅能承受巨大的豎向荷載,而且能承受較大的水平荷載,以適應現代建築物高、重、大的要求。Never lift up load beyond rated capacity of crane
絕對不可提升超過吊臂所能承受的荷載的物件。This type of bearings is separable, which can only carry axial load
是可分離型軸承,只能承受軸向載荷。Conventional earthquake-resistent design involves engineering that a structure under design can carry a set of static lateral.
傳統的抗震設計要求所設計的結構物能承受一組側向靜載荷。Their accuracy, reliability, resistance to corrosion and mechanical load make them suitable for all pressure measuring tasks - in production, development or in the laboratory
它的精確度高可靠性好具有防腐蝕能力能承受機械載荷,適用於所有生產研發或實驗室的壓力測量。The choice of laser output window height is relation to many factors, such as pressure loading, thermal loading, yield stress, influence on wavefront, failure by fatigue. spherical windows can endure higher laser intensity. however, it brings some phaseshifts, which connect with laser windows parameters
激光器輸出窗口厚度的選取與壓力載荷、熱載荷、材料極限強度、厚度對波前的影響、材料疲勞等多種因素有關,由於球殼窗口能承受較高的功率密度,但窗口本身帶來相移,該相移大小與窗口參數有關,根據位相均方根值選擇球殼窗口參數。The dielectric suspension is specifically designed for installation on adss cables and is different than suspension for opgw. due to the relatively fragile nature of the plastic jackets and non - metallic strength members of adss, special care and features are incorporated into the design of the fiberlign dielectric suspension
光纜用單懸垂線夾是將光纜吊掛在直線塔桿上,主要承受檔距內光纜的全部垂直載荷,同時也能承受一定程度的滑差負載10 15 % rts 。In order to ensure that the components are undamaged during the assembling process, the ultimate assembly load of the component needs to be determined so that a reasonable assembly scheme can be made
摘要由於裝配需要,通常需要確定零件在裝配情況下所能承受的極限載荷並選擇合理的裝配方案。High mechanical strength, it can stand heavy dynamic and static load. it is used in high load capacities and low speed with rotational, oscillating or frequent stop - start motion
機械強度大,能承受較大的動、靜載荷。適用於高載低速下的旋轉運動,搖擺運動及經常在載荷下啟閉頻繁而不易形成流體動力潤滑的結合。Mechanically fastened joints of composite materials are mainly components in aircraft structures, which need to be subjected to static loadings and fatigue loadings during working. the prediction of damage failure and fatigue life is one of questions that designers always pay attention to
復合材料連接接頭是復合材料航空結構中的主要部件,在工作過程中,要求能承受一定的靜載荷及疲勞載荷,其損傷失效及疲勞壽命是設計人員關心的問題之一。3 ) the average - strain of cross - section still can be assumed to be keep - in - plane within the whole loading procedure ; the theoretical moment - curvatures obtained by the cross - section keep - in - plane is consistent with the experimental ones. 4 ) the analytical flexural bearing capacity and cfrp - strain are more accurate by assuming the concrete ultimate strain to be 0. 07 instead of 0. 0033 ; 5 ) limiting the cfrp - strain under 0. 01 is reasonable to evaluate the flexural bearing capacity of rc beams retrofitted with cfrp ; 6 ) the initial load is hardly influence the flexural bearing capacity of cfrp - strengthened rc beams
取混凝土的極限壓應變0 . 007代替0 . 0033進行計算的結果能更準確地評浙江大學碩士學位論文2004摘要價加固梁的抗彎承載力和cfrp應變; 5 .在計算cfrp加固梁的抗彎承載力時,限制cfrp的應變在0 . 01以內的措施是恰當的; 6 .梁所承受的荷載的大小對加固後梁的抗彎承載力影響不大。The single direction bearings of them can only carry axial load in one direction, while the double an carry alternating axial load in either direction
單向軸承只能承受一個方向的軸向載荷,雙向軸承能承受兩個方向的交變軸向載荷。This article guarded against explosions the heater to skid the block comprehensive support the structure to carry on the analysis ; found the question which this support structural design exists and has made the corresponding improvement design ; caused to synthesize the support the structure while to satisfy the intensity and rigidity reduced the whole weight ; tends to the optimized design in the material use ; through to synthesizes the support the finite element model to exert the different force of inertia ; obtains under the different load to synthesize the support stress variation rule, thus determine bearing capacity of comprehensive support
摘要本文對防爆加熱器撬塊綜合支架的結構進行了分析,找到該支架結構設計上存在的問題並作了相應的改進設計,使得綜合支架的結構在滿足強度和剛度的同時減輕了整體的重量,在材料的利用上趨于優化的設計;通過對綜合支架的有限元模型施加不同的慣性力,得出不同載荷下綜合支架應力變化規律,從而確定出綜合支架所能承受的最大慣性力。Pile and raft take the load of buildings together. it possesses good whole, high vertical capacity, small settlement of foundation and well performance of balancing differential settlements. it could bear large wind or seismic induced horizon load, and could have large capacity of resisting inclination
樁筏基礎同時具有樁基礎和筏板基礎的優點,樁一筏共同承擔建築物的荷載,它具有整體性好、豎向承載力高、基礎沉降小、調節不均勻沉降能力強的優點,同時可以承受風荷載或地震荷載引起的巨大水平力,抗傾覆能力強。Moreover, when the filaments are treated for 12 minutes, the interfacial shear stress will be lower than that treated for 6 minutes. izod pendulum is used to test the influence of the fiber / matrix bond strength on the low velocity impact responses of the composites. the curves of energy - time, force - time and velocity - time are obtained by a data acquisition system
用擺錘低速沖擊儀對界面粘結強度不同的材料進行沖擊試驗,藉助數據採集系統得到沖擊過程中材料吸收的總能量、承受載荷、擺錘速度等參數與時間的關系曲線,並通過pc機處理,將載荷?時間曲線轉化為載荷?位移曲線。The product output to sprain torque, which make gears the least load and ( with the equal center distance ) can inproue more 30 % bearing capacity than the traditional load capacity
本產品為輸出升扭,使各檔輪所受載荷減小,相同中心距較傳統結構提高承載能力30以上。There is stop groove in the bearing outer ring or it is simultaneously matched with snap rong
使用在對軸承向限位精度要求不高又限們結構簡單的場合.不能承受軸向載荷分享友人