脆化強度 的英文怎麼說

中文拼音 [cuìhuàqiángdù]
脆化強度 英文
brittle strength
  • 脆 : 形容詞1 （容易折斷破碎） fragile; brittle 2 （較硬的食物容易弄碎弄裂） crisp 3 （聲音清脆） （of ...
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. Feldspqr s degree of hardness motion between 6 - 6. 5, specific weight motion bet ween 2 - 2. 5. it s brittleness but have the higher anti - to press the strength, right sour have the stronger chemistry stability. the potassic feldspar s color many is red for meat, and also have the ash, white the brown. the albite is white, ash and buff the anorthite is white or shallow gray

    長石的硬度波動於6 - 6 . 5 ，比重波動於2 - 2 . 5 ，性脆，有較高的抗壓強度，對酸有較強的化學穩定性。鉀長石顏色多為肉紅色，也有灰白褐色。鈉長石為白灰及淺黃色，鈣長石為白色或淺灰色。
  2. High strength steels for civil engineering works. assessment of the embrittling effect of a medium by means of slow tensile testing

    土木工程用高強度鋼.在緩張力試驗條件下對介質脆化作用的評定
  3. It proves that adding up fiber and modified asphalt in the common asphalt mixture can decrease the brittle point temperature and strength the ability of resisting cracking. fiber - reinforced asphalt concrete and glass fiber grid which has been set between the road base and overlay can delaying reflection cracking effectively

    試驗證明，在普通瀝青混合料中加入聚酯纖維以及使用改性瀝青可脆化點溫度降低，增強低溫抗裂性，加入goodroad聚酯纖維和在基層與面層之間鋪設玻纖格柵可有效抑制反射裂縫，值得推廣。
  4. After pretorsion the successor tensile yield limit and strength limit both improved very highly, but the trend of the increase of the strength limit was suspended till the pretorsional capacity reached 17, when the pretorsional capacity was greater than17 ( prestrain value was 81. 19 % of total strain ), the successor strength limit rapid failed and approached the yield limit. this illustrate the a3 steel specimen translate from plasticity into friability after pretorsion strengthen. when the specimen was operated by tension - torsion action, the yield limit had very large improved, but the strength limit changed very little. furthermore, the trend of the increase of the strength limit was suspended till the pretension capacity reached 0. 25 ( prestrain value was 66. 93 % of total strain )

    A3鋼試件在預扭轉后，后繼拉伸屈服極限和強度極限均有很大提高，但強度極限的增大趨勢到預扭轉量為17為止，預扭轉量大於17 （預應變值為總應變的81 . 19 ）后強度極限迅速下降，與其屈服極限接近，這說明a3鋼試件經預扭轉強化后逐漸由塑性轉化為脆性。該預應變值為a3鋼試件的韌脆轉變點。 a3鋼試件在拉伸-扭轉作用下，屈服極限有很大提高，但強度極限沒有多大改變，而且，屈服極限的增大趨勢到預拉伸量為0 . 25應變（預應變量為總應變量的66 . 93 ）后就不再增加。
  5. The results showed that the fracture of the tooth - razor was brittle fracture, the material quality was normal, the main fracture reson was that the carbide in the microstructure of the tooth - razor was distributed as reticulation, the brittleness of the razor was increased and the toughness was decreased, so the tooth of the razor was broken by external force when it was working

    結果表明，該剃齒刀的斷齒屬于脆性斷裂，主要是顯微組織中的碳化物分佈不均勻（呈網狀分佈） ，使刀具的脆性增大而強度、韌性下降，導致刀具在使用過程中由於外力的作用發生斷齒。
  6. The result of macro - quality experiments show : mineral admixtures markedly slow the hydrating velocity of cement slurry, decrease and delay the hydrating max - temperature, in which steel slag is more effective ; expansive agents compensate concrete shrinkage, enhance the concrete dense degree, strengthen the interfacial layer between fiber and cement matrix and improve the physical mechanics qualities of acic ; minimal admixtures markedly improve the concrete workability property, increase the concrete later intensity & density and the capability of anti - chemical attack and anti - permeability ; hybrid fiber reinforces the toughness of obviously acic by the means of anti - cracking effect of fiber with different sizes and different properties in the corresponding construction levels

    實驗結果顯示：鋼渣摻合料能顯著減緩水泥漿體水化速率，降低砂漿的水化溫升並延遲最高溫升時間；補償混凝土收縮，提高混凝土密實度，加強纖維與水泥石的界面粘結，增強混凝土力學性能，但不能明顯改善混凝土韌性。混雜纖維通過纖維的不同尺度與不同性質在相應的結構層次上產生阻裂效應，增韌鋼渣防滲抗裂混凝土；增加混凝土的破壞極限能，極大提高混凝土抗彎曲能力和韌性指數，改善混凝土脆性。
  7. Plastic strain first starts from ambient of the porphyroblast, and then develops to rims of porphyroblast and gradually transfers to the centers of porphyroblasts. the brittle remains in the central parts of porphyroblasts come to be decreased through the plastic deformation development, which is accordance with the banding of intensity in many mylonitization zones on wild occurrences and observation in the fabrics of mylonitization rocks under microscope

    長石眼球構造的形成主要是由長石與石英的韌性差決定的，塑性變形首先從斑晶的周圍部分開始，逐漸向斑晶發展，脆性殘斑核不斷減小，這與剪切帶內糜棱巖化強度分帶相一致。
  8. The cracks extend along the matrix / strengthening - phases interfaces and form the cleavage steps and tear ridges. there appear some very small dimples on the fracture surfaces of the directionally solidified samples, which come from the nb - based solid solution particles in the big plates of the strengthening phases, but no dimples on the fracture surfaces of the as - cast sample. it can be concluded from above results that niobium - niobium silicide based in - situ composites ( rmics ) with a uniformly orientated microstructure can be produced by the ebfzm with high temperature gradient, and their mechanical properties can be increased

    隨著抽拉速率的提高和硅化鈮強化相間距與尺度的減小，材料的室溫拉伸強度和斷裂韌性均有提高， _ b最高可達778 . 4mpa ， k _ （ ic ）達到了46 . 3mpa ? m ~ （ 1 / 2 ） ；試樣的拉伸斷口基本表現為脆性解理斷裂的花樣，裂紋沿基體強化相界面繞過強化相進行擴展，在裂紋擴展方向存在解理臺階，並形成撕裂棱。
  9. The main reason are as following : on one hand, the nd - rich phases in the hydrogen desorpted powders is so brittle that they are easily milled too fine and some are run off seriously, and then inducing low density. on the other hand, the alignment of the magnets prepared by hydrogen desorption are much low. so the hydrogen desorption process should be modified, and the solution methods can be the substitution of traditional ingots with strip cast, the enhancement of the alignment magnetic field and the addition of nd - rich phase or ( and ) lubricant before the press

    主要原因是hd磁粉中的富釹相較脆，在球磨時容易被磨成超細粉而造成過量流失和使磁體燒結不夠緻密；另外一個原因是hd法燒結磁體的易磁化軸的取向度較低，為了提高hd磁體的b _ r和（ bh ） _ （ max ）可對hd工藝進行改進，改進的方法可以是用鑄片代替鑄錠，提高成型磁場強度以及在磁粉成型前加富釹相和潤滑劑。
  10. Fiber / sulfonated sbs composite membranes were made by way of integrating s - sbs with the glass fiber felts, just in connection with the problems of the brittleness and poor strength of s - sbs membranes

    針對s - sbs膜強度較低和干膜較脆的問題，通過復合玻璃纖維氈制備了纖維復合磺化sbs膜。
  11. The multi - purpose tester developed here is aim at testing the mechanics performance of the brittle material, which bases on modular design thought, it contains several modules as the machinery load component, platform of supporting, the function modules and the software system, they can be combined in different function modules to satisfies the need of different application situation. the tester can be used to measure not only general material properties such as elastic modulus, ultimate strain, strength, hardness and toughness, fatigue properties but also various special properties such as the local strength, and surface residual stress at the different location of the brittle component with non - destructive methods. thus the security and reliability of the brittle component can be evaluated and predicted

    本文基於模塊化設計思想，研製了一臺專門針對脆性材料力學性能測試的多功能脆性材料試驗儀，其主要包括機械加載模塊、支撐平臺、功能模塊、測控系統、軟體系統等模塊，通過對這些模塊的不同組合可實現不同的功能及滿足不同應用場合要求;系統除了具有測試脆性材料的彈性模量、極限應變、強度、硬度、韌性等常規性能外，還具有無損測試玻璃構件不同位置的局部強度和表面預應力，進而對玻璃構件的安全可靠性和壽命進行預測等功能。
  12. The results are as follows : ( 1 ) the first industry distribution is disperse and same with the agriculture resource ' s spatial distribution, the second industry distribution is centralized and same with the mineral resources, the third industry centralize on the large and middle cities and the tourism resources abundant region ; ( 2 ) the eco - environment effect of the industrial spatial structure is obvious in gansu ; ( 3 ) the eco - environment and the industrial spatial structure affect each other, strengthening the eco - environment regional difference and aggravating the frailty of the eco - environment

    得出以下結論： （ 1 ）甘肅省第一產業分佈分散且與農業資源的空間分佈態勢基本一致，第二產業發展空間高度集中且與礦產資源分佈一致，第三產業集中在大中城市和旅遊資源豐富的地區； （ 2 ）甘肅省產業空間結構的生態環境效應具有明顯的空間差異； （ 3 ）甘肅省生態環境地域分異與產業空間結構分異交互脅迫，強化了生態環境的地域分異，加劇了生態環境的脆弱性。
  13. After clad plate is rolled, the thickness of al plate has a few changes. the tests firstly produced al clad plate under cold press, then dealed with it under certain temperature. tests tried to find a sound temperature to weaken the

    先對鋁板和鋼板進行冷壓初復合，再在一定溫度下進行熱壓復合，試圖找到合適的熱壓溫度，消除界面脆化，提高復合鋼板的界面力學性能，檢測了試樣的顯微組織和結合強度。
  14. Further, the mechanical behavior and fracture features under flexural load of the c / sic composites are discussed with mechanical properties contract to microstructure and cvi - pip process parameters. the multiple fracture phenomenon of the c / sic with high toughness connected to multiple interface fracture is found, which supplements the conventional composite theory on the relationship between strength and fracture mode

    聯系化學組成及微結構參數、工藝參數，進而研究了彎曲載荷下該c / sic復合材料的行為特徵和失效過程，發現了一種與多重界面失效緊密聯系的、高斷裂韌性的多重損傷累積型材料破壞現象，補充了傳統的脆性基體復合材料強度一斷裂韌性理論。
分享友人
分享到 Line

分享到臉書