腹板的 的英文怎麼說

中文拼音 [fùbǎnde]
腹板的 英文
sternal
  • 腹 : 名詞1 （軀乾的一部分） abdomen; belly; stomach 2 （鼎、瓶子等器物的中空而凸出處） empty and protr...
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 的 : 4次方是 The fourth power of 2 is direction
  1. Furthermore, in order to predict the force at beam tension flange when end - plate yields, kulak method, applied to determine the ultimate strength of the t - stub connections, are modified by introducing a parameter c. the general solution of parameter c is also provided in this paper

    在有限元計算的基礎上，本文分析了影響節點強度的主要因素，包括： （ 1 ）螺栓和端板的強度； （ 2 ）柱翼緣的抗壓強度； （ 3 ）柱腹板的抗壓強度。
  2. In light of the elastic thin plate theory, the author induced equilibrium differential equation of bi - direction cellular slab, which was proved correct through analysis and comparison to result of ansys to with theoretical calculation. through the deflection and bending moment coefficient calculation of bi - direction cellular slab under various boundary conditions, the author brought forward the theory that the deflection of mid - span and bending moment coefficient calculation of mid - span and support of bi - direction cellular slab could be in accordance with solid plates ", which could satisfy the precision of engineering

    本文根據彈性薄板理論，導出了雙向空腹板的平衡微分方程，並通過理論計算和通用有限元程序ansys結果對比，驗證了其正確性；通過對各類邊界條件下雙向空腹板撓度和彎矩系數的計算比較，本文提出：雙向空腹板跨中撓度及跨中、支座彎矩可使用本文空腹板剛度公式查找現有的實心板撓度彎矩系數表進行計算，完全能滿足工程精度要求。
  3. On the basis of this, the paper makes a great deal of calculation and analysis in this part, different parameters " effect and stress gradient are included. local buckling coefficient and the efficient width calculated formula are provided and look forward to take a reference to the redaction of the specification

    本文對此內容進行了較為深入的研究，考慮了多個參數的影響，對各種應力比作用下的楔形腹板的屈曲及屈曲后強度進行了計算分析，得出了考慮翼緣相關作用的楔形腹板屈曲系數及有效寬度系數的計算公式，以期為規范的修訂提供參考。
  4. The investigation of this paper has grate actual and expansive significance and offer methods for the application of rigid frame. the investigation indicate that the ripple web plate ' s critical stress has great improvement than ordinary flat plate and ripple web plate variable cross - section has a rather superiority than constant cross - section portal rigid frame

    本論文所做的研究工作具有很強的現實意義和推廣意義，為門式剛架的應用提供了思路。通過研究表明：波紋腹板的臨界應力比普通的平板有很大提高，而波紋腹板變截面門式剛架與等截面門式剛架進行對比也有較大的優越性。
  5. Often lack of fusion adjacent to the girder web in the transverse groove welds led to the cracking.

    在靠近主梁腹板的橫向坡口焊縫處常常出現未熔透而導致裂紋。
  6. In the hogging condition, double bottom and the side shell remain the ultimate bucking strength, deck and upperwing tank remain the yield stress, and the other parts keep elasticity. then the key to calculate the ultimate strength of ship hull girders is to ascertain the ultimate bucking strength of the stiffened panels. in this regard, the developed formulation is designed to be more sophisticated than previous simplified theoretical method for calculating the ultimate strength of stiffened panels under combined in - plane bending and lateral pressure. fabricatio n - related initial imperfections ( initial deflections and residual stresses ) are included in the panel ultimate strength calculation as parameters of influence. all possible collapse modes involed in collapse of stiffened panels, including overall buckling collapse, column or beam - column type collapse, tripping of stiffeners and local bukling of stiffened web are considered

    確定了船體梁整體破壞時的剖面應力分佈之後，關鍵在於確定板架的極限屈曲強度。本文充分考慮了在縱向彎曲、橫向壓力作用下加筋板可能發生的幾種破壞模式，即板架的整體屈曲破壞、樑柱形式的破壞、筋的側傾、腹板的屈曲並同時考慮了初始焊接殘余應力、初撓度的影響，使其更精確的計算加筋板的屈曲強度。對于加筋板中加強筋腹板的局部屈曲，採用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。
  7. On basis of the producing fact of kiu ming heavy machine ltd, the author get much fact material through inner research, and presents a imagine of new corrugated - web structure of overhead traveling crane. through enough compare and argumentation, this paper presents using sine curve as corrugated sheet of web

    作者根據昆明重機股份有限公司的生產實際，深入調查研究，在掌握大量生產應用實際的資料基礎上，提出了橋式起重機的箱形主梁的新型波形腹板結構的設想，並在充分比較和論證的基礎上提出了以正弦曲線波形作為腹板的波形。
  8. Each bundle of strands is connected to one side of the center web of the two cell box girder.

    每束鋼纜錨固在雙箱梁的中間腹板的一側。
  9. This paper applies nonlinear finite element program bsnfem to analyze the behaviors of eccentrically braced steel frames under cyclic load. the study that comprehensive and systematic analyze the factor of links length, thickness of links flange, distance of links rib, thickness of links rib and angle of brace to be changed affect energy - dissipation capacity of d shape and k shape eccentrically braced steel frames have been some studied before. this paper fills the black in the filed factor of high - span ratio, brace stiffness and brace - to - beam connections to be changed affect energy - dissipation capacity of d shape and k shape eccentrically braced steel trames and any factor to be changed affect energy - dissipation capacity of y shape eccentrically braced steel frames

    對耗能梁段的長度、耗能梁段腹板的厚度、耗能梁段翼緣的厚度、耗能梁段加勁肋的間距、耗能梁段加勁肋的厚度、支撐的夾角等因素的改變對d形、 k形偏心支撐鋼框架耗能的影響，前人已有一些研究，本文對這些因素的影響進行了全面系統的分析，完善了理論分析的不足；而結構高跨比、支撐剛度、支撐與梁的連接形式等因素對d形、 k形偏心支撐鋼框架破壞機理的研究以及各種因素對y形偏心支撐鋼框架破壞機理的影響，則很少有人涉及，本文對此也進行了深入系統的分析，填補了這一研究空白。
  10. The crack surfaces in the web and flange were subjected to visual examination in order to evaluate crack growth regions.

    為了估計各裂紋擴展區，對翼緣和腹板的裂紋表面進行了宏觀檢驗。
  11. To raise the critical stress of the web, we always lay some transverse stiffeners on the web, and also lay some longitudinal stiffeners sometime

    為了提高腹板的臨界應力，通常都設有腹板橫向加勁肋，有時還在梁中段加設縱向加勁肋。
  12. Then with advanced application of ainsys, author proceeded optimal design to corrugated sheet of web and get the optimal solution of corrugated sheet

    此外，利用ansys的高級應用技術，論文還對波形腹板的波形進行了優化設計，並得出了波形的最優解。
  13. Using this new web, the material and stiffening plate of web may reduce too much to reduce the main girder weight of overhead traveling crane and reduce the produced cost

    運用這種腹板，可以大大減少腹板的材料和其上的加強筋，從而使橋式起重機的主梁得以大大減輕，從而降低製造成本。
  14. In the analysis of the elastic local buckling strength of the stiffener ' s web, the elastic critical stress is analytically derived by solving the characteristic value problem involving the governing differential equation under the corresponding loading and boundary conditions

    對于加筋板中加強筋腹板的局部屈曲，則用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。
  15. The author use large - scale finite element software ansys as analyzing tool, use finite element method to comprehensively analyze the oldslabbing - web main girder and the new - corrugated - web main girder. through the analyzing, know the equivalent stress of new web is reduce 57 % than old web

    作者以大型有限元軟體ansys為工具，用有限元方法進行了新型腹板與原來的平直腹板的綜合比較分析，得出了波形腹板結構在同等條件下，等效應力比原腹板減少14左右。
  16. ( 2 ) to clarify the distribution of the vertical stress of the web under the action of the vertical tendon, a three - dimension ( 3 - d ) finite element ( fe ) model is established to calculate the stress distribution of the web under the action of one bind and binds of vertical tendons and investigated the analytical method on vertical stress, the dispersion angle of stress and the calculation of the suitable spacing between the tendons

    （ 2 ）為了研究腹板在豎向力筋作用下的應力場，本文建立了腹板的有限元模型，計算和分析了腹板在單根和多根力筋作用下的應力分佈情況，並探討了豎向應力大小的計算、豎向力筋的應力擴散角和合理間距計算等問題。
  17. Starting from virtual work principle, with the combination of fem, the author led into elastic stiffness practical formulation of bi - direction cellular slab. after comparing the bi - direction elastic stiffness formulation with the approximately stiffness formulation, the author drew such a conclusion that if the hole - rib is comparatively big, the elastic stiffness of bi - direction cellular slab calculated by approximately formulation would be comparatively small, and therefore the elastic stiffness could calculated by the formulation illustrated in this paper

    本文從虛功原理出發，結合有限元方法，給出了雙向空腹板的彈性剛度實用計算公式，並與近似剛度公式進行對比分析，並得出結論：在雙向空腹板孔間肋較大情況下，利用近似公式計算雙向空腹板的彈性剛度偏小，可按本文提出的彈性剛度公式進行計算。
  18. Second, change the diaphragm ’ s space between, retain the other thing, analyze the influence of the stress and deformation of box ? girder cross section and the beam web. based on the analysis upwards, the writer studied the rule of the influence of the stress and deformation box ? girder cross section and the beam web with different diaphragm ’ s space between. according to the results of finite element analysis, the writer puts forward some suggestions which will provide some reference for the following design

    本文利用ansys有限元分析程序，對指定斷面，不同曲率的曲箱梁，建立完備的有限元模型，分別對二個方面的問題進行了分析:其一，通過對箱梁在有無跨中橫隔板時截面頂板及腹板的變形和應力分佈的對比分析，闡述了設置跨中橫隔板的重要性;其二，在相同工況下，通過改變橫隔板的設置間距，分析對箱梁翼緣及腹板的受力影響。
  19. The author, applying the program of ansys, built a nonlinear model of rc bi - direction cellular slab, and, from the comparison of equivalent - span and equivalent - thickness solid plate, drew several important conclusions. meanwhile he also pointed out that the stiffness of cellular slab would become weaker because of the holes of cross - section which make the tare weight 40 % down comparing to solid plate, but if the weakness of tare weight was considered, the cellular slab still remained the excellent features of integration and stiffness, by which the cellular slab can be put into use of large - span

    本文利用有限元程序ansys ，建立了鋼筋混凝土雙向空腹板的非線性計算模型，並和等跨等厚度實心板進行分析對比，從而得出了一些重要結論，指出：在空腹板自重比實心板減少40左右後，空腹板的剛度雖然由於截面的開孔而削弱，但考慮自重減少后，空腹板仍表現出整體性好、剛度大的特徵，從而實現較大跨度樓板的工程應用。
  20. Experimental results show that the new cfrt - column to steel - beam joints proposed in this paper possess good earthquake resistant capacity. the infilled concrete benefit to restrain the buckling deformation of column webs, increase the strength and stiffness of the joint. the lengthened stiffener can transfer much more beam moment, make the strength of the joint increased

    試驗表明，在保證焊接質量的前提下，本文提出的新型方鋼管混凝土柱?鋼梁的節點具有良好的抗震性能；內填混凝土有利於抑制柱腹板的屈曲變形，增加節點的承載力和剛度；加勁肋長度的增加有利於傳遞梁端彎矩，使節點的承載力提高。
分享友人
分享到 Line

分享到臉書